Claas Jaguar 900-830 (493) Forage Harvesters Repair Manual ES

File List:

00 0298 080 0.pdf
00 0303 968 1.pdf
00 0305 072 0.pdf

00 0298 080 0.pdf:

JAGUAR 900 – 830
Introduction
General data
Manual validity
Using the manual
Texts and figures
Index with the structure of constructive groups
Search and find
Direction signs
Abbreviations
Technicalities
General repair instructions
Technical data
Indications for correct repair
Self-locking screws
Liquid screw insurance
Steel roller chains
connecting link
Tapered ring joints
Disassembly
Mounting
Head key joints
Disassembly
Mounting
Bearings with tension ring
Disassembly
Mounting
Bearings with tensioner sleeve
Disassembly
Mounting
Tension bushing
Disassembly
Mounting
Threadings with adjustment ring
Screw in
Non-tight joint with adjusting ring
Screw connections with sealing cone
Hydraulic hoses
Laying the hoses
Joint surface work
Replacement parts
Tightening torques
Tightening torques for normal metric threads
Tightening torques for metric fine threads
Tightening torques for hydraulic threads and air conditioning threads with sealing cone and O-ring DIN 3865
Tightening torques for hydraulic threads with adjusting ring DIN 3861
Tightening torques for threaded fittings of the SDS hydraulic system
Tightening torques for oscillating hydraulic threadings
Tightening torques for hollow screws DIN 7643
Tightening torques for threaded fittings of the SDE hydraulic system with adjustable direction
Tightening torques for brake line joints
Tightening torques for helical thread clamps
Tightening torques for spring-loaded helical thread clamps
Tire tightening torques
CCN Explanation
CCN (CLAAS Component Number)
General indications
Electrical regulations
Hydraulic regulations
CCN (CLAAS Component Number)
Security
General data
To especially take into account
Signaling of warning and alarm indications
General protection and safety rules at work
First aid
Risk of injury from hydraulic fluid
Leave the machine
Put the machine out of service
Raise the machine on supports
Adjustment and maintenance work
Welding work
03 Chassis
0330 Rear drive steering axle
Drive steering axle
Preparation for work
special tool
Technical instructions
Disassemble
shaft body
Preparation for work
special tool
Technical instructions
Preparation for work
special tool
Technical instructions
Disassemble
Conical drive
Preparation for work
special tool
Technical instructions
Disassemble
Check the play of the toothed sides
Differential
Preparation for work
special tool
Technical instructions
Disassemble
If the measured clearance is equal to the indicated clearance value (a), skip this work step!
If the measured torque equals the specified value for torque (b), skip this work step!
Bearings
Technical instructions
Disassemble
wheel hub
Preparation for work
special tool
Technical instructions
Completely remove the wheel hub
Install the complete wheel hub
Steering bars
Technical instructions
Adjust tread and steering angle
05 Address
0505 Address
Hydraulic steering cylinder (3023)
Technical instructions
Disassemble
0510 Automatic steering
AUTO PILOT steering angle sensor (B006)
Technical instructions

00 0303 968 1.pdf:

JAGUAR 990-830Chop
Introduction
General information
To especially take into account
Manual validity
Supply set
Repair kit 00 2926 032 0
A084 Generation II bedknife adjustment module (CLAAS JAGUAR 500, 496)
Transformation
Indications
Security
Sequence of work steps
Put the machine out of service
Disassembly
Remove A084 bedknife adjustment module (CLAAS JAGUAR 500, 496)
Mounting
Assemble A084 generation II bedknife adjustment module (CLAAS JAGUAR 500, 496)
Supply set
Repair kit 00 2406 842 1
A084 Generation II bedknife adjustment module (CLAAS JAGUAR 502, 499, 498)
Transformation
Indications
Security
Sequence of work steps
Put the machine out of service
Disassembly
Remove A084 Counterblade adjustment module (CLAAS JAGUAR 502, 499, 498)
Mounting
Assemble A084 generation II bedknife adjustment module (CLAAS JAGUAR 502, 499, 498)
Bedknife software, configuration and adjustment
Software update
Update A084 SBM software (bed knife adjustment module)
Configuration and backup
Check settings and backup
Bedknife Adjustment
Sharpen the blades and adjust the bedknife distance

00 0305 072 0.pdf:

JAGUAR 990-830Cooling system
Introduction
General information
Security
Manual validity
Quick navigation
Supply set
Repair kit 00 2789 091 0
XL radiator screen: Replace the perforated plate
Transformation
General security measures
Put the machine out of service
To especially take into account
Disassembly
Remove the radiator screen
Assembly 00 2789 091 0
XL radiator screen: Replace the perforated plate
Mounting
Install the radiator screen
Supply set
Repair kit 00 2789 092 0
Radiator screen M: Replace the perforated plate
Transformation
General security measures
Put the machine out of service
To especially take into account
Disassembly
Remove the radiator screen
Assembly 00 2789 092 0
Radiator screen M: Replace the perforated plate
Mounting
Install the radiator screen