Claas Medion 330 H (931) Combines Operator Manual FR

File List:

00 0298 665 2.pdf

00 0298 665 2.pdf:

Introduction
Introduction
Contents
General advice
Driving on the road
Driving on the road – slope compensation chassis
Important
Rating plate/serial number
Nameplate
Machine number
Engine number
Cutting deck nameplate
Straw chopper
Cabin serial number
Safety tips
Safety tips
Safety stand
Extinguisher
Battery cut-off switch
Brake chock (not for all countries)
Installing the wedges
Safety stickers with warning pictograms
Technical characteristics
CLAAS MEDION 330 H
Security devices
Before commissioning
Necessary work before initial commissioning
Cabin with automatic air conditioning
Air conditioning automation
Control and indication elements
Commissioning the air conditioning automation
Cabin temperature adjustment
Manual adjustment of fan-evaporator speed
Connecting the ECON service
Disconnecting from the ECON service
REHEAT operation (remove fog from cabin windows)
Outdoor temperature display
Switching the temperature display to ˚ Fahrenheit
Heating of the foot area
Fault display, F0 temperature sensor error (passenger compartment, blue)
Fault display, error temperature sensor F1 (output, yellow)
Fault display, F2 temperature sensor error (external, red)
Cabin with air conditioning
Cabin with fan
Cabin with fan and air conditioning
Cabin with fan and heater
Heating of the foot area
Reheat system (eliminates fogging on cabin windows)
Incident, cause or possible remedy – air conditioning
Opening and closing the cabin roof
Open the cabin roof
Close the cabin roof
Steering column
Ignition lock
Driving informant
How the driving informant works
Harvest monitor informant
How the harvest informant works
Control console (up to machine no. …)
Control console (from mcine No. …)
Multifunction lever (up to machine No. …)
Multifunction lever (from machine No. …)
Central electrical system
Changing the position of the steering column
“Air-cushioned” driver’s seat (optional)
Height adjustment
Weight adjustment
Seat tilt adjustment
Seat depth adjustment
Kidney support
Armrest tilt
Horizontal adjustment of the driver’s seat
Mechanical driver’s seat (optional)
Weight adjustment
Height adjustment
Seat tilt adjustment
Seat depth adjustment
Kidney support
Armrest tilt
Horizontal adjustment of the driver’s seat
Rear ladder
Driving the combine
Engine speed selector
Start the engine
Adjusting the difficulty of maneuvering the forward control lever
Speed ​​ranges
Driving characteristics
Direction
Pedal brake
Hand brake
Stop the engine
CLAAS 4-Trac system
Manual Operation
d lighting / gangway ramp
Driving lights, working lights and mirrors
Gateway ramp
Take out the gangway ramp
Tilt compensation
Tilt compensation (up to machine No. …)
Control console (up to machine no. …)
Function check (up to machine no. …)
Tilt compensation (from machine No. …)
Control console (from machine No. …)
Function check (from machine No. …)
Adjusting the limit switches
Adjusting the front stops
Adjusting the rear stops
Hydraulic diagram (up to machine No. …)
Tilt compensation
Hydraulic diagram (from machine No. …)
Tilt compensation
Use – cutting apron
Assembly of the cutting deck
Connect the cardan shafts (up to machine No. …)
Connect the cardan shaft on both sides (on the right side – cutting deck from 6.00 m)
Connect the cardan shafts (from machine No. …)
Connect the cardan shaft on both sides (on the right side – cutting deck from 6.00 m)
Connecting hydraulic hoses
Connecting the cables
Place the crutches
Adjustments at the cutting deck
Dividers
Corn lifters
Cutting blade
Dismantling the blades
Installing the blades
Blade head height adjustment
Adjusting the blade clamps
Replacement blade
Cutting deck shoes
Reel fingers
Reel drive
Horizontal reel adjustment (mechanical)
Horizontal reel adjustment (hydraulic)
Reel variator
Feed screw
Adjusting the distance from the bottom plate
Adjusting the position of the feed fingers
Adjusting the scraper bars
Adjusting the scraper angles to the supply channel
Adjusting the position of the feed fingers
Replace blades in the field
Use – basic machine
Feed channel
Supply chains
Front tool reversing device
Adjustment of the cutting deck flexibility springs (up to machine No. …)
Adjusting the cutting height display
Adjustment of the cutting deck descent speed (to machine No. …)
Adjusting the lowering speed of the front tool (from machine No. …)
CLAAS cutting height preselection
Starting the pre-selection of cutting heights (up to machine No. …)
Starting the pre-selection of cutting heights (from machine No. …)
Display of the contact pressure of the front tool
Cutting deck clutch
Connect the threshers (up to machine No….)
Disconnect the cutting deck (up to machine No. …)
Connect the cutting deck (from machine No. …)
Disconnect the cutting deck / control panel (from machine No. …)
Disconnect the cutting apron / multifunction handle (from machine No. …)
Threshing bodies
Destoner bin
Start/stop of threshers
Connect the threshers (up to machine No. …)
Connect the threshers (from machine No….)
Disengage the threshers
Adjusting the concave
Stop screw for concave adjustment
Adjusting the concave
Adjusting the concave
Basic adjustment of the different concaves
Trimming
Drummer’s Diet
Adjusting the mixer speed (up to machine No. …)
Adjusting the mixer speed (from machine No. …)
Eliminate the beater windings
Straw puller
Anti-splash fabric
Cleaning the threshing bodies
Shakers and cleaning
Aerator shakers
Cleaning the shakers
Cockscombs/Sawtooth Separators
Cleaning box
Preparation table
Cleaning ventilation
Electrical fan speed adjustment
Adjust the ventilation direction
Adjusting the slatted grilles
Lower grilles
Dismantling the upper grilles
Mounting the upper grilles
Disassembly of the lower grilles
Mounting the lower grilles
Tightening torque of axial screw connections for upper and lower grilles
Dynamic slope compensation (3D cleaning)
Return of the oats
Flow control device
Adjustment for different crops
Adjusting sensor sensitivity
Commission the flow control device
Grain recovery
Auger and auger buckets
Elevators
Grain hopper
Hopper Covers
Emptying the hopper
Rear access ladder with safety switch (up to machine No. …)
Hopper drain tube
Connect and disconnect the hopper drain (to machine no. …)
Connecting and disconnecting the hopper drain (from machine No. …)
Evacuation hatch at the level of the hopper drain tube
Driving the hopper emptying augers
Hopper Drain Shear Bolt
Hopper fill level indicator 100%
Hopper 100% filling level indicator buzzer
Straw chopper / chaff spreader
Straw chopper
Checks to be carried out before putting the straw chopper into service
Adjusting the hash length
Cross blade adjustment
Commissioning the straw chopper
Adjusting the spreading width
Electrical adjustment of the spreading plates
Adjustment of the spreading plates
Stopping the straw chopper and adjusting to windrowing
Couple the transport trailer to the cutting deck
Grid and threshing tables
Grid table
Threshing Table
Incident, cause or remedy – basic machine
Maintenance – basic machine, cutting deck
Important maintenance tips
Important Maintenance and Safety Tips
Maintenance and lubrication table
Maintenance tables
Lubricant tables
Hydraulic system
Check the oil level (up to machine No. …)
Check the oil level (from machine No. …)
Hydraulic oil change
Replace the hydraulic oil filter on the hydrostatic pump
Replace the hydraulic oil filter on the tilt control (up to machine No….)
Replace the hydraulic oil filter on the tilt control (from machine No. …)
Filling instructions when changing hydraulic oil
Hydraulic pump adjustment
Bleed air from reel cylinders
Foot brake / brake fluid
Gearboxes
Adjusting the gearbox
Check the oil level
Oil drain
Reducers
Oil drain
Gearbox/blade drive
Oil level check / oil change
Feed channel
Tighten the supply chains
Tension the drive chain for the intermediate shaft (from machine No. …)
Tighten the feed drum drive chain
Adjusting the rotating crown
Elevator chains
Tighten the grain elevator chain
Tighten the grain elevator chain
Drive belts / drive chains – basic machine
General advice
Left drive scheme
Straight training scheme
Remove the belt (1)
Install the belt (1)
Remove the belt (2) (up to machine No. …)
Install the belt (2) (up to the machine No. …)
Remove the belt (3)
Install the belt (3)
Remove the belt (4) (up to machine No. …)
Install the belt (4) (up to machine No. …)
Remove the belt (4) (from machine No. …)
Install the belt (4) (from machine No. …)
Remove the belt (5)
Install the belt (5)
Remove the belt (6)
Install the belt (6)
Remove the belt (7)
Install the belt (7)
Remove the belt (8)
Install the belt (8)
Remove the belt (9)
Install the belt (9)
Remove the belt (10)
Install the belt (10)
Remove the belt (11)
Install the belt (11)
Remove the belt (12)
Install the belt (12)
Remove the belt (14)
Install the belt (14)
Remove the belt (15)
Install the belt (15)
Remove the belt (16)
Install the belt (16)
Remove the belt (20)
Install the belt (20)
Remove the belt (21) (up to machine No. …)
Install the belt (21) (up to the machine No. …)
Remove the belt (21) (from machine No. …)
Install the belt (21) (from machine No. …)
Remove the belt (22)
Install the belt (22)
Remove the belt (25)
Install the belt (25)
Remove the belt (26) (up to machine No. …)
Install the belt (26) (up to the machine No. …)
Remove the belt (27) (up to machine No. …)
Install the belt (27) (up to the machine No. …)
Remove the belt (28)
Install the belt (28)
Remove the belt (30)
Install the chain (30)
Remove chain (31)
Install the chain (31)
Remove chain (33)
Install the chain (33)
Remove the belt (35) (from machine No. …)
Install the belt (35) (from machine No. …)
Drive belts / drive chains – cutting deck
General advice
Cutting deck drive diagram
Tighten the blade drive belt (40)
Tighten the feed auger drive chain (41)
Tighten the reel drive chain (42)
Removing and installing reel drive belt (43)
Tighten the reel drive chain (44)
Tighten the reel drive chain (45)
Cabin / air conditioning
Cleaning the filters
Air conditioner
Clean the capacitor
Check the refrigerant level
Replace the filter dryer
Required filling quantities of refrigerant R 134 a
Maintenance work to be carried out before harvest
Extinguisher
Have the fire extinguisher checked for proper operation
Checking the shaker crankshaft speed
Sensor adjustment
Machines with on-board computer
Straw chopper
Replace articulated knives
Dismantling the blades
Installing the blades
Replace the counter blades
Winterizing Tips for Combines
Maintenance – engine
Important maintenance tips
Important tips and safety regulations
Maintenance and lubrication table
Maintenance table
Lubricant table
Maintenance – engine
Engine compartment hatch – hopper
Access from the cabin to the engine compartment
Fuel system
Fuel tank
Fuel shut-off valve
Water decanter / fuel pre-filter (additional equipment – small model)
Exploded view of the fuel pre-filter:
Water decanter / fuel pre-filter (additional equipment – large model)
Exploded view of the water decanter / fuel pre-filter:
Fuel pre-filter
Fuel Filter
Bleed the air from the fuel system
Checking the engine oil level
Engine oil change
Drain used oil
Oil filter
Filling the engine oil
Tighten the alternator V-belt
Cooling system
Cooling liquid
Engine block water drain plugs
Radiator
Fill with coolant
Overpressure (up to machine No. …)
Overpressure (from machine No….)
Anti-corrosion and anti-freeze protection
Warning sign
Cooling water temperature
Stopping an engine that has overheated
Radiator cage
Cleaning the radiator cage
Raise the radiator cage
Swivel the oil cooler upwards (to machine no. …)
Swivel the oil cooler upwards (from machine No….)
Cleaning the oil cooler
Cleaning the water radiator
Dry air filter
Alarm system
Clean the air filter suction grille
Cleaning the air filter
Removing the main air filter cartridge
Installing the main air filter cartridge
Security cartridge
electricity
Three-phase alternator
Engine problems, cause or remedy
Winterizing Tips for Engines
Engine conservation
Lubrication plan – basic machine
Lubricants and advice
Lubrication plan – slope compensation
Lubricants and advice
Alphabetical index
Lubrication plan – basic machine