Claas Quadrant 4000 (773) Balers Technical System EN

File List:

00 0290 916 2.pdf
00 0302 343 1.pdf
00 0302 565 2.pdf
00 0305 772 0.pdf
CHP-numbers for connectors CLAAS HARNESS PARTS.pdf

00 0290 916 2.pdf:

QUADRANT 4000
Table of contents
Introduction
Safety rules
Safety and hazard information
Marking of warnings and hazard prevention notes
Validity of manual
Validity of manual
CCN explanation
CCN (CLAAS Component Number)
Electric systems standard
Hydraulic system standard
CCN (CLAAS Component Number)
0410 Service brake trailed machine
Hydraulic service brake
Pneumatic service brake
Dual-line brake system trailer brake valve
Description of function
Testing and adjustment
09 Hydraulic system
0910 Pumps
Baling pressure hydraulic system pump
0920 Valves
Baling pressure control valve
Measured values table
0980 Hydraulic circuit diagram
Hydraulic circuit diagram
10 Electrical / Electronic equipment
1005 Power supply
Main power supply
Measured values table
Description of function
1012 Modules / sensors
Module pin assignment
1040 Yield measuring
Crop moisture sensor
Measured values table
Description of function
1080 Electronic circuit diagram
Introduction into circuit diagrams
Overview of designations
CLAAS cable marking
Power supply
Communication
Electric circuit diagrams
SCM00: Retrofit kit in the tractor for power supply via ISOBUS connector
SCM01 up to serial number 77300096: Power supply, CAN Bus, diagnosis and Quadrant module
SCM01 from machine number 77300097: Power supply, CAN Bus, diagnosis and Quadrant module
SCM02: Sensors
SCM03: Actuators
SCM04: Additional control unit adapter
SCM05: Baling ram load indicator
SCM06: Electric wrapping release
SCM07: Lighting
SCM08: Work lights
Connector database (chp CLAAS)
Example of representation of key numbers (CHP)
Key number (CHP)
Connector representation (CHP)
1085 Networks
Measured values table
Description of function
45 Baling system
4500 Baling system
Baling pressure control and baling ram load indicator
Measured values table
Description of function
46 Tying system
4610 Twine wrapping
Electric wrapping release
Measured values table
Description of function
Sequence diagram of wrapping and fault monitoring
4620 Knotter
Cleaning fan
Description of function
60 Crop discharge / straw discharge
6040 Bale discharge
Bale discharge
Measured values table
Description of function
DUO PAC bale stacker
Description of function
75 Central lubrication system
7505 Reservoir / Pump
Electric central lubrication system
Measured values table
Description of function
7515 Lubrication system / Lines
Central lubrication system grease distribution
92 Diagnosis
9210 Error codes machine
Fault indicators on the operating terminal
Position of components
Electric system
A Terminal / modules
E Lighting
M Motor (electric)
R Potentiometer/resistors
U Switch – External operation
V Electronic component
X Connectors
Y Solenoid coil
Z Actual value switch
Hydraulic system
1001-1999 Oil tank / filter / oil cooler
2001-2999 Pump / motor
3001-3999 Hydraulic cylinders
5001-5999 Accumulator
6001-6999 Valve, mechanically actuated
7001-7999 Valve, hydraulically actuated
9001-9999 Measuring points / Gauges

00 0302 343 1.pdf:

PROFI CAM 3
Table of contents
General information
Marking of warnings and hazard prevention notes
First-aid measures
CCN explanation
CCN (CLAAS Component Number)
Electric system standard
Hydraulic system standard
CCN (CLAAS Component Number)
10 Electrical / Electronic equipment
1030 Board computer / Indicators
Camera system
Description of function
1097 Testing / Measuring / Adjusting
Testing / measuring / adjusting the PROFI CAM
Checking the fuse in the video channel select box (C102)
Testing the video camera connector (C055)
1098 Fault / remedy
Fault / remedy PROFI CAM
The video monitor (C101) shows no image or cannot be switched on (indicator light fails to light up)
Video monitor (C102) displays a blue image either permanently or temporarily
The video monitor image is blurred
Replacing the fuse in the video channel select box (C102)
Connection and connecting cable with video camera (C055)

00 0302 565 2.pdf:

Sensor system
Table of contents
CCN explanation
CCN (CLAAS Component Number)
Electric system standard
Hydraulic system standard
CCN (CLAAS Component Number)
Introduction
Safety rules
Safety and hazard information
10 Electrical / Electronic equipment
1097 Testing / Measuring / Adjusting
Test report of the angle sensor (0011780.x)
Application of test report
Required tools
Test report of the angle sensor (0011780.x)
Testing / Measuring / Adjusting of angle sensor (0011780.x)
1. Reason for test
2. Mechanical test of angle sensor
3. Electric test with CDS
4. Electric test with multimeter
5. Mechanical test of connecting cable
Completing the machine
Test report of position and speed sensors
Application of test report
Required tools
Sensor variants
Part numbers of speed sensors
Part number of position sensor
Test report of position and speed sensors
Testing / measuring / adjusting of position and speed sensors
1. Reason for test
2. Mechanical test
3. Electric test with CDS
4a. Installation dimensions
Check of installation dimension
Installation dimensions of gearbox speed sensor (0011 799.x) and cam speed sensor (0011 810.x)
Installation dimension of position sensor (0011 815.x)
4b. Installation position
Centring of sensor
Metal-free zone
5. Electric test with multimeter
Voltage measurement
Direction of rotation and speed sensor (0011 605.x)
Measured values table
6. Mechanical test of connecting cable
Completing the machine
Test report of the urea sensor (00 0773 207 x)
Application of test report
Required tools
Parts number of the urea sensor
Test report of the urea sensor
Testing / measuring / adjusting urea sensor
1. Reason for test
2. Mechanical test
3. Mechanical test of connecting cable
4. Electric test with multimeter
5. Component test with the CDS

00 0305 772 0.pdf:

Table of contents
Introduction
Notes on the manual
Information about this Technical Systems Manual
Using the manual
Document structure based on subassemblies
Search and find
Directions
Identifying warnings
Hazard signs
Signal word
Safety rules
Safety signs and warnings
Requirement made on technical staff
Children in danger
Hazard areas of the machine
Instructors travelling along during fieldwork
Risk of injury from rotating shafts
Structural alterations of the machine
Optional equipment and spare parts
Control of running machine
Technical condition
Respecting technical limit values
Danger from machine parts that continue rotating
Keeping safety devices functional
Personal protective equipment
Wearing suitable clothing
Removing dirt and loose objects
Parking the machine safely
Unsuitable operating utilities
Safe handling of service fluids and auxiliary utilities
Environmental protection and disposal
Keeping the cab free of chemicals
Avoiding fires
Potentially fatal electric shock from overhead lines and lightning strike
Electric shock from electric system
Noise may damage your health
Pre-loaded machine parts
Liquids under pressure
Compressed air
Toxic exhaust gases
Hot surfaces
Safe access and leaving
Working only on the stopped machine
Hazards during repairs
Raised machine parts and loads
Danger from welding work
Checking and charging the battery
Preparations for cases of emergency
10 Electrical / Electronic equipment
1098 Fault / remedy
ISOBUS checklist for fault analysis
Use of the checklist
1. Fault when loading the graphical user interface of the ISOBUS implement
1.1 The graphical user interface for an ISOBUS implement (object pool) is not loaded to the terminal
1.2 Loading the graphical user interface of the ISOBUS implement is not finished or is interrupted
1.3 The graphical user interface for an ISOBUS implement is loaded to the wrong terminal
2. Fault when assigning function keys
2.1 No keys available for assigning, no AUX input available
2.2 Assigned function keys without a function or faulty
2.3 Assignment of function keys after restarting no longer available
3. Task management fault (TC BAS)
3.1 Meter readings from the implement not available or remain at zero
3.2 Import/export of iso.xml not possible/only partially possible
3.3 Missing reference tracks in import/export
3.4 Individual tasks cannot be deleted from the terminal
3.5 Folder structure task data on the USB stick
4. Section Control fault (TC SC)
4.1 TC SC at the wrong terminal
4.2 TC SC without a function/only with a partial function
4.3 Incorrect switching on or off of TC SC
5. Testing and measuring
5.1 Testing and measuring ��� terminal socket
5.2 Testing and measuring ��� ISOBUS socket
5.3 Testing and measuring ��� diagnostic socket
6. 6.1 ISOBUS check (load object pool)
6.2 ISOBUS CAN logging (assigning of function keys)
6.3 ISOBUS CAN logging (assigned key without a function)
6.4 ISOBUS CAN logging (assignment no longer available, gets lost)
6.5 ISOBUS CAN logging (in the event of a fault with task management)
6ral problems)
7. ISOBUS components/AEF compatibility/software statuses
7.1 ISOBUS components and fault description
7.2 ISOBUS functionalities
7.3 Software statuses/AEF compatibility

CHP-numbers for connectors CLAAS HARNESS PARTS.pdf:

CLAAS HARNETS
Table of contents
10 Electrical / Electronic equipment
1081 Overview of connectors
CLAAS HARNESS PARTS (CHP)