File List:
00 0300 825 1.pdf
00 0300 825 1.pdf:
DISC 9200 C AS
Introduction
Safety instructions
Safety and danger instructions
Manual validity
CCN Explanation
CCN (CLAAS Component Number)
General indications
Electrical regulations
Hydraulic regulations
CCN (CLAAS Component Number)
09 Hydraulic
0900 General instructions for the hydraulic installation
Hydraulic functions
Function description – connection to the tractor hydraulic system
0920 Valves
Valve block I DISCO 9200 C AS
Additional lift valve block
0980 Hydraulic connection diagram
DISCO 9200 C AS hydraulic connection diagram
Hydraulic connection diagram DISCO 9200 C AS with own on-board hydraulic system
10 Install. electrical/electronic
1012 Modules / sensors
Module A068 – mower control
Denominations
Denominations
Hydraulic oil temperature sensor (B123)
Function Description
Adjustment
Pin occupation
Table of measured values
Support pressure sensor, left side arm (B183)
Function Description
Adjustment
Table of measured values
Support pressure sensor, right side arm (B184)
Function Description
Adjustment
Table of measured values
Mower revolution speed sensor – front center (B198)
Function Description
Adjustment
Pin occupation
Table of measured values
Mower revolution speed sensor – center left (B201)
Function Description
Adjustment
Pin occupation
Table of measured values
Mower revolution speed sensor – center right (B202)
Function Description
Adjustment
Pin occupation
Table of measured values
Left mower position sensor (B276)
Function Description
Adjustment
Pin occupation
Table of measured values
Right mower position sensor (B277)
Function Description
Adjustment
Pin occupation
Table of measured values
Mower pressure sensor (B296)
Function Description
Adjustment
Table of measured values
Left swath belt lowering stop sensor (B400)
Function Description
Adjustment
Pin occupation
Table of measured values
Right swath belt lowering stop sensor (B401)
Function Description
Adjustment
Pin occupation
Table of measured values
1080 Electronic connection diagram
Electrical connection diagram DISCO 9200 C AS
SCM 01 – Power supply / CAN Bus
Denominations
SCM 03 – Hydraulic functions
Denominations
SCM 04 – Left outgoing unit
Denominations
SCM 05 – Right outgoing unit
Denominations
SCM 06 – Front mower unit
Denominations
SCM 07a – Lighting
Denominations
SCM 07b – LED Lighting
Denominations
SCM 08 – Self-feeding of the tapes
Denominations
SCM 09 – Options
Denominations
SCM 10 – Plug summary
1081 Plug summary
Socket database (chp CLAAS)
Example of key number representation (CHP)
Key number (CHP)
Plug Representation (CHP)
1085 Networks
General indications
75 Central lubrication
7515 Lubrication/piping equipment
Central lubrication system
Table of measured values
Function Description
Absorption and transport phase
Denomination
Main pump components
Denomination
LED error indications
Central lubrication system plan
Grease points
92 Diagnosis
9230 ISO Error Codes
FMI fault code (Failure Mode Indicator)
General indications
FMI 00 (signal too large)
FMI 01 (signal too small)
IMF 02 (implausible signal)
FMI 03 (voltage too high)
FMI 04 (voltage too low)
FMI 05 (current too low)
FMI 06 (current too high)
FMI 07 (mechanical failure)
FMI 08 (frequency signal defective)
IMF 09 (communication failure)
FMI 10 (signal change too fast)
IMF 11 (multiple failure)
FMI 12 (defective ECU)
FMI 13 (signal outside calibration range)
IMF 16 (non-existent parameter)
FMI 17 (ECU not responding)
FMI 18 (power supply failure)
FMI 19 (software requirements not met)
IMF 95 (no signal change)
FMI 96 (CAN-Bus system defective)
IMF 97 (implausible state)
IMF 98 (warning)
IMF 99 (Info)
DISCO 9200 C AS error codes
DTC (Diagnostic Trouble Code) Summary
Location of components
Hydraulic installation
1000 Oil tank / oil filter / oil radiator
2000 Pump/motor
3000 Hydraulic Cylinders
5000 Pressure accumulators
6000 Valves with mechanical drive
9000 Measuring points / indicator instruments
Electrical installation
To Terminal/modules
B Sensors
and lighting
and electromagnetic coils
Claas Technical System PDF
Claas Technical System PDF
Claas QUANTUM 6800-4500 GT P (615) Loader Wagons Technical System DE
Claas Technical System PDF
Claas Technical System PDF
Claas Technical System PDF
Claas Technical System PDF
Claas QUANTUM 3800 K 3500 P-K-S (613) Loader Wagons Technical System DE