File List:
00 1174 322 X.pdf
00 1175 997 X.pdf
00 1178 451 X.pdf
00 1178 682 X.pdf
00 1174 322 X.pdf:
ELIOS 210Stage V
CCN (CLAAS Component Number)
CCN Explanation
CCN (CLAAS Component Number)
General indications
Electrical regulations
Hydraulic regulations
CCN Index
Introduction
Manual validity
Validity of this diagnostic manual
01 Engine
0125 Fuel/injection system
fuel supply circuit
Measurement value table
Function Description
Hydraulic diagram of the fuel supply circuit
Fuel supply pressure control
fuel injection circuit
Measurement value table
Function Description
Calibration of the accelerator pedal sensor «B153» and the engine speed adjustment sensor «B154»
Calibration of CLAAS POWER MANAGEMENT sensors
Hydraulic diagram of tuel injection circuit
fuel return circuit
engine wiring
Power readiheets
Work preparation
Unit Conversions
Calculation formula
0130 Lubricating oil system
Engine lubrication circuit
Measurement value table
Function Description
Hydraulic diagram of the engine lubrication circuit
Engine lubrication pressure control
0135 Cooling system
Engine cooling circuit
Measurement value table
Function Description
Engine thermostat control
0140 Exhaust gas system
Engine exhaust circuit
Measurement value table
Function Description
Exhaust gas and recycled exhaust gas circuit diagram
Checking the “EGR” cooler
0145 Air suction
Engine air intake circuit
Measurement value table
Function Description
0150 Engine coupled parts
Engine start
Measurement value table
Function Description
0155 Engine adjustment
Engine speed setpoint
Measurement value table
ction Description
0165 Exhaust gas aftertreatment
Engine aftertreatment system
Measurement value table
Function Description
Automatic regeneration
Regeneration when stopped or in service
0198 Incident / solution
18F-2 — Oxygen sensor failure
18F-3 — Oxygen Sensor Circuit (B539) Shorted
18F-4 — “B539” oxygen sensor circuit shorted
601-2 — “B539” oxygen sensor circuit open
602-2 — “B539” oxygen sensor circuit open
605-3 — Oxygen sensor failure
606-2 — “B539” oxygen sensor circuit open
607-3 — Oxygen sensor failure
607-4 — Oxygen sensor failure
609-2 Control module: internal error
60A-4 — Oxygen sensor failure
60B-3 — “B539” oxygen sensor circuit shorted
60B-4 — “B539” oxygen sensor circuit shorted
60C-3 — Oxygen sensor failure
60C-4 — Oxygen sensor failure
02 Gears / clutch / cardan shaft
0202 Complete component
Transmission kinematics
Transmission 12 + or
24+24 transmission with hydraulic doubler
24+12 transmission with hydraulic ransmission with hydraulic shuttle and hydraulic rear PTO clutch
Preponderance
0220 Mechanical investment
mechanical inverter
0222 Hydraulic inversion
REVERSHIFT hydraulic reverser
Measurement value table
Function Description
Clutch pedal operation and adjustment
“TCU A057” Transmission Control Module Interface Menu
Tractor model configuration
Clutch Pedal Calibration Menu
Error messages that may be displayed during the calibration procedure
Clutch pressure sensor calibration menu
Error messages that may be displayed during the calibration procedure
Lever progressiveness adjustment menu
Pedal progression adjustment menu
Hydraulic duplicator progressivity adjustment menu
Limp Home function activation menu
Help menu for the diagnosis of “Revershift”plicator control and the clutch pedal
Checking the supply pressure of the hydraulic shuttle clutches
0230 Mechanical gear
Mechanicaator, speeds and mechanical ranges
0234 Load Switching Gear
«Twinshift» hydraulic duplicator
0242 Differential
Rear differential lock
Measurement value table
Operating law
Checking Differential Supply Pressure
0252 Electrohydraulic drive of the front axle
Traction on the four wheels
Measurement value table
Operating law
Checking the four-wheel drive power take-off supply pressure
03 Chassis
steering axis
Traction on the four wheels
04 Brake
0405 Service brake
Service brake
0425 Hydraulic Trailer Brake
Hydraulic Trailer Brake
Measurement value table
05 Address
0505 Address
Main address
Checking the steering pressure relief valve «7026»
Control of the opening pressure of the anti-shock valves «7153»
06 Lifting device
0605 Rear linkage
Mechanical rear hydrauft
neutral position
Lowering position
Rise position
Checking the rear linkage shock valve
Electronic rear lift
elevattributor
Rear Linkage Calibration Procedure
Shock valve pressure adjustment
Preliminary operations
special tool
Adjustment
08 Drives
0802 Rear PTO
Electrohydraulically controlled rear PTO
Operating law
Checking the power take-off brake supply pressure
Checking the power take-off clutch pressure
Mechanically controlled rear PTO
Operating law
09 Hydraulics
0910 Bombs
2-pump hydraulic circuit
3-pump hydraulic circuit
Control of the flow rate of the steering hydraulic pump «2018»
Checking the flow rate of the auxiliary hydraulic pump «2027»
Checking the flow rate of the hydraulic pump «2015» (elevator)
0915 Hydraulic pipes
Transmission hydraulic circuit 12-12
24-24 transmission hydraulic circuit with mechanical duplicator
24-24 transmission hyc circuit with “TWINSHIFT” hydraulic doubler
Transmission hydraulic circuit 24-12 «REVERSHIFT»
0920 Valves
Hydraulic circuit with two pumps aibutors
Hydraulic circuit with two pumps and three distributors
Hydraulic circuit with two pumps and three distributors with flow regulator in the middle
Hydraulic circuit of three pumps and three distributors with flow regulator in the middle
Hydraulic circuit of three pumps and electrohydraulic distributors
0935 Hydraulic system control/supervision
Hydraulic system monitoring
Measurement value table
0980 Hydraulic connection diagram
Transmission hydraulic circuit diagram 12-12
Drawing of the hydraulic circuit of the 24-24 transmission with mechanical duplicator
Diagram of the hydraulic circuit of the 24-24 transmission with «TWINSHIFT» hydraulic duplicator
Transmission hydraulic circuit diagram 24-12 «REVERSHIFT»
10 Install. electrical/electronic
1010 Central electrical systnt engine fuse box
Fuse assignment
Relay assignment
Main fuse box
Dashboard fuses
Right pillar fuse box
Fuse assignment
Left pillar rel Relay assignment
Right console fuse box (rear linkage and electrohydraulic distributors)
Fuse assignment
Relay assignment
Relay assignment
Mass points
1012 Modules / sensors
Module overview
A015 Engine management module
A057 Transmission control module
A058 Elevator module
A060 Hydraulic system control module
A101 Control panel module
A101 Control panel module (tractor with mechanical rear power take-off)
A101 Control panel module (tractor with hydraulic rear PTO)
A117, A118, A119, A120 Distributors 1, 2, 3, 4
A147 Rear linkage control panel
A174 Multifunction Control Module
1015 Cable sets
Cable set
W22 – Ground cable
Connector List
W45-1 – Positive Launch Cable
Connector List
engine wiring
W02 – Motor wiring
Connector List
Cab and platform wiring
W04 – Cab roof wiring
Connector List
W04-3 – Front windshield washer motor wiring
Connector List
W04-4 – Cab roof power wiring
Connector List
W16 – H4 lighting wiring
Connector List
W17 – Rotating Flashing Light Wiring (Platform)
Connector List
W19 – Front wiper wiring
Connector List
W25 – Gearbox +/- control wiring
Connector List
W29 – Control panel wiring (tractor with mechanical inverter)
Connector List
W29 – Control panel wiring (tractor with REVERSHIFT)
Connector List
W31 – Right console wiring (tractor with mechanical shuttle)
Connector List
W31 – Right console wiring (tractor with REVERSHIFT)
Connector List
W35 – Rotating flasher retrofit wiring
Connector List
W36 – Cab roof, heating and air conditioning wiring
Connector List
Front wiring
W05 – Hood wiring
Connector List
W05-1 – Hood-Dashboard connection wiring
Connector List
W33 – Front power take-off wiring
Connector List
W33 -1 – Front power take-off connection wiring to the solenoid valve
Connector List
Rear linkage and distributor wiring
W10 – Rear linkage control wiring (with electrohydraulic distributors)
Connector List
W10-1 – Wiring of the electrohydraulic distributors
Connector List
W10-2 – Distributor Control Power Wiring
Connector List
W10-3 – Rear Linkage Up/Down Switch Wiring
Connector List
W11 – Rear linkage control wiring (without electrohydraulic distributors)
Connector List
W11-1 – Rear linkage wiring (without electrohydraulic distributors)
Connector List
W11-3 – Rear linkage external control wiring
Connector List
transmission wiring
W06 – Trailer brake wiring
Connector List
W30 – Main wiring (tractor with mechanical inverter)
Connector List
Main wiring (tractor with REVERSHIFT)
Connector List
1080 Electrical connection diagram
SCM02 Road signs
SCM02-01 Rotating flashing light (platform version)
Component List
Wiring list
SCM02-01 Rotating flashing light (cab version)
Component List
Wiring list
SCM02-02 Driving lights and acoustic warning
Component List
Wiring list
SCM02-03 Position, turn signal and brake lights (platform version)
Component List
Wiring list
SCM02-03 Position, turn signal and brake lights (cab version)
Component List
Wiring list
SCM04 Elevator, electrohydraulic distributors and power take-off
SCM04-01 Rear linkage (with electrohydraulic distributors)
Component List
Wiring list
SCM04-01 Rear linkage (without electrohydraulic distributors)
Component List
Wiring list
SCM04-02 Front and rear power take-off (mechanical rear power take-off)
Component List
Wiring list
SCM04-02 Front and rear power take-off (hydraulic rear power take-off)
Component List
Wiring list
SCM06 Transmission
SCM06-01 Four Wheel Drive and Differential
Component List
Wiring list
SCM06-02 REVERSHIFT and TWINSHIFT
Component List
Wiring list
SCM06-03 Mechanical duplicator
Component List
Wiring list
SCM07 Accessories
SCM07-01 Cabin roof
Component List
Wiring list
SCM10 CAN Network
SCM10-01 CAN network (tractor with mechanical inverter)
Component List
Wiring list
SCM10-01 CAN Network (tractor with REVERSHIFT)
Component List
Wiring list
SCM11 Power
SCM11-01 Power supply (tractor with mechanical inverter)
Component List
Wiring list
SCM11-01 Power (tractor with REVERSHIFT)
Component List
Wiring list
SCM12 Tractor connections. Tools
SCM12-01 Power socket (tractor with mechanical inverter)
Component List
Wiring list
SCM12-01 Power outlet (tractor with REVERSHIFT)
Component List
Wiring list
SCM13 Braking system
SCM13-01 Pneumatic braking system
Component List
Wiring list
SCM18 Engine
SCM18-01 Engine
Component List
Wiring list
SCM18-02 Engine Controls (Tractor with Mechanical Inverter)
Component List
Wiring list
SCM18-02 Engine Controls (Tractor with REVERSHIFT)
Component List
Wiring list
SCM19 Dashboard
SCM19-01 Instrument panel
Component List
Wiring list
1085 Networks
CAN bus network architecture
CAN bus network
Location of CAN bus resistors
92 Diagnosis
Presentation of error codes
Introduction
Viewing error codes
Description
«CCN», «SPN» and «IMF» standard
IMF 00 (too important signal)
FMI 01 (signal too low)
IMF 02 (impla signal)
FMI 03 (voltage too high)
FMI 04 (voltage too low)
FMI 05 (current too low)
FMI 06 (current too high)
FMI 07 (mechanical error)
(incorrect frequency signal)
IMF 09 (communication error)
FMI 10 (signal change too fast)
IMF 11 (multiple errors)
FMI 12 (“ECU” defective)
FMI 13 (out of calibration range signal)
IMF 16 (non-existent parameter)
FMI 17 (ECU not responding)
FMI 18 (power supply error)
FMI 19 (software conditions not satisfied)
FMI 95 (no signal modification)
FMI 96 (defective CAN bus system)
IMF 97 (implausible state)
IMF 98 (warning)
IMF 99 (Info)
9210 Machine Error Codes
Conversion table of the codes indicated on the dashboard screen
List of error codes
Diagnostic sheets
Checking the circuits. recommendations
0x30c – B153 accelerator pedalsor error
0x30d – B153 accelerator pedal sensor error
0x30e – B153 accelerator pedal sensor error
0x30f – Engine speed adjustment sensor error B154
0x310 – Engine d adjustment sensor error B154
0x313 – Engine speed adjustment sensor error B154
0x314 – Right brake pedal contactor error Z127
0x315 – Four Wheel Drive Switch Error S001
0x316 – Z234 Four Wheel Drive Oil Pressure Switch Error
0x317 – Z234 Four Wheel Drive Oil Pressure Switch Error
0x318 – Differential lock switch error S094
0x319 – Z235 differential oil pressure switch error
0x31a – Z235 differential oil pressure switch error
0x31b – Engine RPM memory button error 1 S178
0x31c – Engine speed switch error + S188
0x31d – Engine speed switch error – S189
0x31e – Engine RPM memory button error 2 S179
0x31f – Hydraulic duplicator error
0x320 – Gearbox +/- control error C089
0x321 – Gearbox +/- control error C089
0x322 – PTO brake solenoid valve error Y338
0x323 – Rear PTO clutch solenoid valve error Y325
0x324 – Control module: internal error
0x325 – Rear PTO “on/off” switch error S114
0x326 – 540 rpm PTO switch error connected Z1 0x327 – 540 rpm PTO switch error connected Z161
0x328 – 540 rpm PTO switch error connected Z161
0x329 – 540-1000 rpm PTO contactor error Z208
0x32a – 540-1000 rpm PTO contactor error Z208
0x32b – 540-1000 rpm PTO contactor error Z208
0x32c – PTO speed selection error
0x32d – Proportional PTO contactor error not activated Z210
0x32e – Proportional PTO contactor error not activated Z210
0x32f – Proportional PTO contactor error not activated Z210
0x330 – Proportional PTO contactor error Z162
0x331 – Proportional PTO contactor error Z162
0x332 – Proportional PTO contactor error Z162
0x333 – PTO speed selection error
0x334 – Error of the «CLAAS Power Management» sensors B047 and B228
0x335 – “CLAAS Power Management” sensor error B047
0x336 – “CLAAS Power Manage error B228
0x337 – Z175 PTO oil pressure switch error
0x338 – Z175 PTO Oil Pressure Switch Error
0x339 – PTO brake solenoid valve error Y338
0x33a – Rear PTO clutch solene error Y325
0x33b – PTO clutch control pressure error
0x33c – Rear PTO RPM sensor error B142
0x350 – Left brake pedal contactor error Z126
0x352 – Writing error in the internal memory of the A101 control panel module
0x593 – Internal fault of the A101 control panel module
0x594 – Dashboard module (DBD) A101 failure
0x596 – Internal fault of the A101 control panel module
0x597 – CAN bus error
0x598 – Dashboard module (DBD) A101 failure
0x599 – Four-wheel drive automation switch error S335
0x59a – B117 steering angle sensor error
0x59b – B227 theoretical forward speed sensor error
0x59c – Front PTO relay error
0x59d – PTO Safety Disable Switch Error S334
0x626a – Hydraulic oil temperature too high
0x7100 – Clutch pedal sensor B361 output voltage too high
0x7101 – Clutch pedal sensor B361 output voltage too low
0x7102 – Clutch pedal sensor B361 output signal too low
0x7103 – Clutch pedal sensor B361 output signal too high
0x7104 – B361 clutch pedal sensor signals and approach contactor activation not synchronized
0x7105 – B383 reverse clutch pressure sensor output signal greater than 5 V
0x7106 – B383 reverse clutch pressure sensor output signal less than 0.2 V
0x7107 – Supply voltage of pressure sensors B383, B384 and B385 above 5.5 V
0x7108 – Supply voltage of pressure sensors B383, B384 and B385 below 4.5 V
0x7109 – Slow forward clutch pressure sensor output signal B384 greater than 5 V
0x710a – Absence of electrical signal from the reverse lever under torque C073 or no presence of the driver in the seat (depending on equipment)
0x710b – Forward and reverse signals sent simultaneously by the shuttle lever under torque C073
0x710c – Forward and neutral position signals sent simultaneously by the shuttle lever under torque C073
0x710d – Reverse and neutral position signals sent simultaneously by the shuttle lever under torque C073
0x710e – Forward, reverse and neutral position signals sent simultaneously by the shuttle lever under torque C073
0x7110 – Slow forward clutch pressure sensor output signal B384 less than 0.2 V
0x7111 – B385 fast forward clutch pressure sensor output signal greater than 5 V
0x7112 – Fast forward clutch pressure sensor output signal B385 less than 0.2 V
0x7114 – Pressure in the reverse clutch less than 0.25 bar during pressurization
0x7115 – Reverse clutch pressure greater than 0.9 bar when reverse clutch is not powered
0x7116 – Reference values of the reverse clutch solenoid valve Y233 outside the ranges of use
0x7119 – Current return of the reverse solenoid valve Y233 has not been detected when it receives power
0x711a – Detection of intensity return of the reverse solenoid valve Y233 when it does not receive power
0x711b – Reverse clutch soid valve Y233: difference between the measured current and the reference current
0x711d – Abnormal reverse clutch slippage
0x711e – Reverse clutch: 0.5 bar difference between the measureessure and the reference pressure
0x7120 – Transmission Control Module (TCU) Failure A057
0x7120 – Transmission Control Module (TCU) Failure A057
0x7120 – Transmission Control Module (TCU) Failure A057
0x7120 – Transmission Control Module (TCU) Failure A057
0x7120 – Dashboard module (DBD) A101 failure
0x7122 – Transmission control module (TCU) A057 supply voltage less than 9 V
0x7123 – A057 transmission control module (TCU) supply voltage greater than 16 V
0x7124 – Corruption of flash memory calibration parameters
0x7125 – CAN bus error
0x7127 – Oil temperature below − 20 °C
0x7129 – Hydraulic oil temperature sensor B123 signal too high
0x712a – Hydraulic oil temperature sensor B123 signal too low
0x712b – Intermediate gearbox speed sensor failure B229
0x7 – Gearbox speed intermediate sensor signal failure B229
0x712e – Excessive slip in fast forward clutch
0x712f – Excessive slip in slow forward clutch
0x713e – Overcurrent on all transmisn control module (TCU) outputs A057
0x7145 – Transmission Control Module (TCU) Power Error A057
0x7146 – CAN bus communication error
0x7147 – CAN bus communication error
0x7212 – Detection of overcurrent in the supply of the transmission safety solenoid valve Y506
0x7214 – Overcurrent detection in the return of the transmission safety solenoid valve Y506 or in the return of the rear PTO clutch solenoid valve Y325
0x7215 – Pressure in the fast forward clutch less than 0.25 bar during pressurization
0x7216 – Fast forward clutch pressure greater than 0.9 bar when fast forward clutch is not powered
0x7217 – Reference values of the fast forward clutch solenoid valve Y507 outside the ranges of use
0x7218 – Current return of the fast forward clutch solenoid valve Y507 has not detected when it receives power
0x7219 – Detection of intensity return of the fast forward clutch solenoid valve Y507 when it does not receive power
0x721a – Fast forward clutch solenoid valve : difference between the measured current and the reference current
0x721b – Fast forward clutch: 0.5 bar difference between the measured pressure and the reference pressure
0x721c – Overcurrent detection in the fast forward clutch solenoid valve Y507 or in the reverse clutch solenoid valve Y233
0x721d. Pressure in the slow forward clutch less than 0.25 bar during pressurization
0x721e. Inching clutch pressure greater than 0.9 bar when inching clutch is not powered
0x721f. Reference values of the slow forward clutch solenoid valve Y508 outside the ranges of use
0x7225 – Overcurrent detection in the slow forward clutch solenoid valve Y508
0x7226. No current return of the slow forward clutch solenoid valve Y508 has been detected when it receives power
0x7227 – Intensity rn detection of the slow forward clutch solenoid valve Y508 when it does not receive power
0x722a. Slow forward clutch solenoid valve Y508: difference between the measured current and the reference curre 0x722b. Slow forward clutch: 0.5 bar difference between the measured pressure and the reference pressure
0x722e – Filter differential pressure detection when engine is running and transmission oil temperature is above 20°C
0x722f – Z102 Filter Bypass Pressure Switch Failure
0x7233 – Low pressure circuit contactor Z184 detects a pressure lower than 7 bar
0x7236 – Low pressure circuit contactor Z184 detects pressure when engine is off
0x7237 – Low pressure circuit contactor Z184 detects pressure when the engine is started and the transmission safety solenoid valve Y506 is not powered
0x7239 – Transmission control module (TCU) failure A057
0x723b – Transmission control module internal memory write error
9220 Diesel Engine Error Codes (J1939)
Description
Engine Manaement Module Error Code List “A015”
Location of components
Electrical installation
To Terminal. Modules
B Sensors
C Electrical, electronic devices
and lighting
G Voltage source
H Sing device. Light indicator
M Motor (electric)
R Potentiometers. Resistors
S Switches. Switches (control in cabin)
T Switches. Terminal control
U Switches. External controls
V Electronic components
W Antenna
X Connections
and electromagnetic coil
Z Actual value switches
00 1175 997 X.pdf:
Technical systems
CCN Explanation
CCN (CLAAS Component Number)
General indications
Electrical regulations
Hydraulic regulations
CCN (CLAAS Component Number)
Introduction
Manual validity
Validity of diagnostic manual
01 Engine
0125 Fuel/injection system
fuel supply circuit
Measurement value table
Function Description
Hydraulic diagram of the fuel supply circuit
Fuel supply pressure control
Checking fuel pressures
fuel injection circuit
Measurement value table
Function Description
Hydraulic diagram of the fuel injection circuit
fuel return circuit
engine wiring
0130 Lubricating oil system
Engine lubrication circuit
Measurement value table
Function Description
Hydraulic diagram of the engine lubrication circuit
Engine lubrication pressure control
0135 Cooling system
Engine cooling circuit
Measurement value table
Function Description
Engine thermostat control
0140 Exhaust gas system
Engine exhaust circuit
Measurement value table
Function Description
Exhaust gas and recycled exhaust gas circuit diagram
Checking the “EGR” cooler
0145 Air suction
Ee air intake circuit
Measurement value table
Function Description
0150 Engine coupled parts
Engine start
Measurement value table
Function Description
0155 Engine adjustment
Engine speed setpoint
Measurement value table
Function Description
Calibration of the accelerator pedal sensor «B153» and the engine speed adjustensor «B154»
0165 Exhaust gas aftertreatment
Engine aftertreatment system
Function Description
Principle diagram of the urea circuit
AdBlue® and exhaust gas circulation
Engine power reduction
Automatic regeneration
Regeneration when stopped or in service
02 Gears / clutch / cardan shaft
0202 Complete component
Transmission kinematics
Transmission 24+24 mechanical reverser, mechanical duplicator
24 + 12 transmission with hydraulic shuttle, hydraulic doubler and mechanical rear PTO clutch
24 + 12 transmission with hydraulic shuttle, hydraulic doubler and hydraulic reO clutch
Preponderance
0220 Mechanical investment
mechanical inverter
0222 Hydraulic inversion
REVERSHIFT hydraulic reverser
Measurement value table
Function Description
Clutch pedal operation and adjustment
“TCU A057” Transmission Control Module Interface Menu
Tractor model configuration
Clutch pedal calibrati Error messages that may be displayed during the calibration procedure
Calibration of clutch pressure sensors
Error messages that may be displayed during the calibration procedure
Lever progressiveness adjustment menu
Pedal progression adjustment menu
Hydraulic duplicator progressivity adjustment menu
Limp Home function activation menu
Help menu for the diagnosis of “Revershift”, the duplicator control and the clutch pedal
Checking the supply pressure of the hydraulic shuttle clutches
0230 Mechanical gear
Mechanical duplicator, speeds and mechanical ranges
0242 Diff
Rear differential lock
Measurement value table
Operating law
Checking Differential Supply Pressure
0252 Electrohydraulic drive of the front axle
Traction on the four wheels
Measurement value table
Operating law
Checking the four-wheel drive power take-off supply pressure
03 Chassis
0325 Front drive steering axle
Traction on the fourels
04 Brake
0405 Service brake
Service brake
0425 Hydraulic Trailer Brake
Hydraulic Trailer Brake
Presentation of the hydraulic trailer braking system block (XXXXI)
Function Description
Hydraulic diagram of the hydraulic trailer braking system block (XXXXI)
Hydraulic Trailer Braking System Block Pressure Chart (XXXXI)
Operating laws
Degraded mode
05 Address
0505 Address
Main address
Checking the steering pressure relief valve «7026»
Control of the opening pressure of the anti-shock valves «7153»
06 Lifting device
0605 Rear linkage
Mechanical rear hydic lift
neutral position
Lowering position
Rise position
Shock valve pressure adjustment
Preliminary operations
special tool
Adjustment
08 Drives
0802 Rear PTO
Electrohydraulically controlled rear PTO
Operating law
Checking the power take-off brake supply pressure
Checking the power take-off clutch pressure
Mechanly controlled rear PTO
Operating law
09 Hydraulics
0910 Bombs
Hydraulic circuit of two pumps
Three-pump hydraulic circuit
0915 Hydraulic pipes
Transmission hydraulic circuit 24-24 and 12-12 (mechanical reverser and mechanical duplicator)
Transmission Hydraulic Circuit 24-12 REVERSHIFT
0920 Valves
Mechanical auxiliary distributors
Rear mechanical auxiliary distributors
Multifunction hydraulic block
Function Description
0935 Hydraulic system control/supervision
Hydraulic system monitoring
Measurement value table
0980 Hydraulic connection diagram
Hydraulic transmission circuit 24-24 and 12-12 mechanical
Transmission Hydraulic Circuit 24-12 REVERSHIFT and TWINSHIFT with Hydraulic Clutch Rear PTO
Hydraulic circuit of two pumps
Hydraulic circuit of three pumps, mechanical control distributors
10 Install. electrical/electronic
1010 Central electrical system
Front engine fuse box
Main fuse and relay box
Tractor with REVERSHIFT hydraulic shuttle
Fuse assignment
Relay assignment
Tractor with mechanical inverter
Fuse assignment
Relay assignment
Right pillar fuse box
Cab left pillar relays
Dashboard relay
Mass points
1012 Modules / sensors
A015 Engine management module
Denomination
Module Connections
A057 Transmission control module
A101 Control panel module
A101 Control panel module (transmission with mechanical inverter)
A101 Control panel module (transmission with REVERSHIFT inverter)
1015 Cable sets
Cable set
W22 – Ground cable
Connector List
W45 – Motor electrical supply wiring
Connector List
W45-1 – Positive Launch Cable
Connector List
W45-2 – Displaced terminal cable
Connector List
cab wiring
W04 – Cab roof wiring – Main
Connector List
W04-3 – Windshield washer pump wiring
Connector List
W04-4 – Cabin Top Power Wiring
Connector List
W12 – Rear fin wiring
Connector List
W16 – H4 lighting wiring
Connector List
W19 – Front wiper wiring
Connector List
W31 – Right console wiring (transmission with REVERSHIFT inverter)
Connector List
W31 – Right console wiring (transmission with mechanical shuttle)
Connector List
W33_2 – Front power take-off control wiring
Connector List
W35 – Rotating flashing light wiring
Connector List
engine wiring
W02 – Motor wiring
Connector List
W08 – Air conditioning wiring (engine part)
Connector List
Front wiring
W05 – Hood wiring
Connector List
W33_1 – Front power take-off solenoid valve wiring
Connector List
Dashboard wiring harness
W29 – Dashboard wiring (transmission with REVERSHIFT inverter)
Connector List
W29 – Dashboard wiring (transmission with mechanical shuttle)
Connector List
W29_1 – Brake pedal wiring
Connector List
transmission wiring
W06 – Trailer brake wiring
Connector List
W30 – Transmission wiring (transmission with REVERSHIFT inverter)
Connector List
W30 – Transmission wiring (transmission with mechanical shuttle)
Connector List
1080 Electrical connection diagram
Help for using electrical diagrams
Use of links
Color code of electrical cables
Tractor equipped with a REVERSHIFT inverter transmission
SCM06-01 Transmission 1/2 (control part)
Component List
Wiring list
Claas Technical System PDF
Claas Technical System PDF
Claas S900-S450 SOJA LEXION TUCANO (440) Combine Technical System DE
Claas Technical System PDF