File List:
00 0292 837 1.pdf
00 0292 930 0.pdf
00 0295 168 6.pdf
00 0292 837 1.pdf:
OPERATOR
1 Regarding this instruction manual
1.1 Information on the instruction manual
1.1.1 Validity of the manual
1.1.2 Manual handling
1.1.3 Symbols and indications
1.1.4 Technical instructions
2 Security
2.1 Safety instructions
2.1.1 To take special account
2.1.2 Proper machine application
2.1.3 Logically foreseeable inappropriate application
2.1.4 General safety and accident prevention rules
3 Product Description
3.1 Summary and operation
3.1.1 OPERATOR Summary
3.1.2 OPERATOR operating mode
3.2 Identification plates and identification numbers
3.2.1 Spare parts and technical questions
3.2.2 OPERATOR identification plate
4 Control and display instruments
4.1 CLAAS OPERATOR
4.1.1 Terminal
4.1.2 Terminal program
4.1.3 Menu overview
4.1.4
4.1.5 Menu
4.1.6 Menu
00 0292 930 0.pdf:
QUADRANT 2200 Advantage RotoFeedQUADRANT 2200 Advantage RotoCut
1 Regarding this instruction manual
1.1 General data
1.1.1 Application of this manual
1.1.2 About this user manual
1.1.3 Technical characteristics
2 Security
2.1 General data
2.1.1 General information
2.1.2 Authorized use
2.1.3 Reasonably foreseeable misuse
2.1.4 Safety regulations
2.1.5 Symbols applicable to danger indications
2.1.6 Highway driving
2.1.7 Accident prevention
2.1.8 Waste disposal
2.1.9 Residual risks
2.2 Graphic danger symbols
2.2.1 Description
2.2.2 Location of safety stickers
2.3 Safety equipment
2.3.1 Signal lighting
2.3.2 Reflective equipment
2.3.3 Surety
2.3.4 Chocks
2.3.5 Parking brake
2.3.6 Flywheel brake
2.3.7 Locking the pick-up
2.3.8 Locking the bale exit ramp
3 Machine Description
3.1 Existing models
3.1.1 Designation of machines
3.2 Overview and functions
3.2.1 Left side
3.2.2 Right side
3.3 Work and service positions
3.3.1 General information
3.3.2 Front of the baler
3.3.3 Top of the baler
3.4 Identification plate and serial number
3.4.1 Spare parts and technical information
3.4.2 Position of the nameplates
3.4.3 Machine nameplate
3.4.4 Rudder nameplate
3.5 General operating principle
3.5.1 Bale pressing cycle
3.6 Transmission and drive
3.6.1 Power transmission
3.6.2 Friction clutch
3.6.3 Main drive
3.6.4 Rotor drive
3.6.5 Feeder drive
3.6.6 Knotter operation
3.7 Reception of the harvest
3.7.1 Pick-up
3.7.2 Reducing rollers
3.7.3 Short straw plank
3.8 Power set
3.8.1 Rotor
3.8.2 RotoCut cutting device (optional)
3.8.3 Carrier
3.9 Pressing system
3.9.1 Piston and pressing channel
3.10 Tying system
3.10.1 Tying process
3.10.2 Thread compartments
3.10.3 Thread shortage indicator
3.10.4 Needles
3.10.5 Knotters
3.10.6 Turbofan
3.11 Unloading bales
3.11.1 Control block
3.11.2 Bale unloading ramp
3.11.3 Bale unloading ramp position detector (optional)
3.11.4 Bale unloading sensor (optional)
3.11.5 Humidity sensor (optional)
3.11.6 Bale ejector
3.12 Centralized lubrication
3.12.1 General information
3.12.2 Manual centralized lubrication
3.12.3 Automatic centralized lubrication
3.12.4 Supplemental lubrication
3.13 Axis
3.13.1 General information
3.13.2 Single axis
3.13.3 Tandem axle
3.13.4 Tracking tandem axle
3.14 Service brake
3.14.1 General information
3.14.2 Pneumatic braking
3.14.3 Hydraulic braking
3.14.4 Active hydraulic braking
3.15 Hydraulic system
3.15.1 Hydraulic oil tank
3.16 Equipment
3.16.1 Ladder
3.16.2 Front ladder support
3.16.3 Stirrup
3.16.4 Electronic module
3.16.5 12 V socket
4 Control and display instruments
4.1 CLAAS OPERATOR
4.1.1 Presentation
4.1.2 Screen
4.1.3 Key identification
4.1.4 Description of the CLAAS OPERATOR Using menus
4.2 ISOBUS terminal
4.2.1 Presentation
4.2.2 General information
5 Technical data
5.1 Baler
5.1.1 General information
5.1.2 Dimensions
5.1.3 Weight
5.1.4 Hooking
5.1.5 Cardan shaft
5.1.6 Feeding and pressing
5.1.7 Tying device
5.1.8 Wheels
5.1.9 Hydraulic circuit
5.1.10 Screw tightening torques
5.1.11 Braking
5.1.12 Speed - Brake/Axis Type
5.1.13 Greasing and lubrication
5.1.14 Sound levels
5.2 Safety devices
5.2.1 Security screw
5.2.2 Overload safety
5.3 Tractor
5.3.1 Required power
5.3.2 PTO
5.3.3 Hookup
5.3.4 Electrical connections
5.3.5 Hydraulic connections
5.3.6 Hydraulic circuit and oil
5.3.7 Braking
6 Preparation of the machine
6.1 General data
6.1.1 First commissioning
6.1.2 Equipment control
6.2 Cardan shaft
6.2.1 Safety regulations
6.2.2 Cardan shaft adjustment
6.2.3 Adaptation of the cardan shaft length
6.2.4 Transation kit, 8 grooves (optional)
6.2.5 Double-joint wide-a gimbal
6.2.6 Positioning the cardan shaft
6.3 Trailer support
6.3.1 Recommendations
6.3.2 Types of fixing
6.3.3 Hitch fixing
6.3.4 Adaptation of the fork hitch/oscillating bar hitch
6.3.5 Hitching the baler to the tractor
6.3.6 Positioning the cardan shaft
6.4 Hydraulic connections
6.4.1 Location of flexible ducts
6.4.2 Sear and pick-up
6.4.3 General hydraulics of the baler
6.5 Electrical connections
6.5.1 Marking of electrical cables
6.5.2 Lights
6.5.3 Battery cable (optional)
6.5.4 Power supply to the baler and CLAAS OPERATOR
6.5.5 Baler power supply with ISOBUS cable
6.6 Service brake
6.6.1 Hydraulic brake
6.6.2 Active hydraulic brake
6.6.3 Air brake
6.7 Tied
6.7.1 Yarn quality
6.7.2 Preparation
6.7.3 Thread tensioner adjustment
6.7.4 Thread placement
6.7.5 Placing the thread in the knotters
Manual shot of a bundle
Baler equipped with mechanical tying shot
Baler equipped with electric tying trigger
6.7.6 Checking the settings
6.8 Cutting device
6.8.1 Safety regulations
6.8.2 Control
6.8.3 Placing the blades
6.8.4 Assembly of false blades (optional)
6.8.5 Unused blades and dummy blades
6.9 Machine loading
6.9.1 Lifting the baler
6.9.2 Baler stowage
7 Management
7.1 General data
7.1.1 Baler user
7.1.2 Opening doors and casings
7.2 Movements with the baler
7.2.1 Equipment control
7.2.2 Preparations for transportation
7.2.3 Road travel
7.2.4 Arrival at the field
7.2.5 Moving around the field
7.2.6 Parking
7.3 Before each use
7.3.1 Reminders
7.3.2 Cardan shaft
7.3.3 Baler maintenance
7.4 Commissioning in the field
7.4.1 Usage tips
7.4.2 Commissioning of the machine
cardan shaft
Material transfer system
After a machine stop
7.4.3 Bale unloading ramp
Manual bale unloading ramp
Hydraulic bale unloading ramp
7.4.4 Bale ejector (option)
7.4.5 Tracking axis (option)
7.5 Pick-up
7.5.1 Important
7.5.2 Oscillating pick-up wheels
7.5.3 Foldable pick-up wheels
7.5.4 Pick-up height
7.5.5 Reducing rollers
7.6 Cutting device
7.6.1 RotoCut cutting device (optional)
7.7 Bale parameters
7.7.1 Bale adjustments
Bale length adjustment
Baler equipped with mechanical tying shot
Baler equipped with electric tying trigger
7.8 CLAAS OPERATOR
7.8.1 Pressing pressure
7.8.2 Bale length
7.8.3 Automatic greasing
7.8.4 Counters Menu
7.8.5 Faults
7.8.6 Manual triggering of the tying process
7.8.7 Pressing channel filling indicator *
7.8.8 Blade activation/deactivation (RotoCut option)
7.8.9 Cutting frame (RotoCut option)
7.8.10 Pressing process
7.9 Unclogging the baler
7.9.1 How to avoid traffic jams?
7.9.2 Safety regulations
7.9.3 Pick-up jam
7.9.4 Jam of the reduction rollers
7.9.5 Feed rotor jam (RotoFeed option)
Rotor unclogging
7.9.6 Cutting rotor jam (RotoCut option)
7.10 After use
7.10.1 Reminders
7.10.2 Baler protection
7.10.3 Disconnecting the baler
7.10.4 Daily checks
7.10.5 Daily cleaning
8 Incident and solution
8.1 Tied
8.1.1 Origin of tying problems
8.1.2 Resolution of tying problems
8.2 Centralized lubrication
8.2.1 Resolution of centralized lubrication problems
8.3 CLAAS OPERATOR
8.3.1 Faults displayed on the control terminal
8.3.2 Electrical circuit
8.3.3 PTO failure
8.3.4 Transfer system
8.3.5 Bale unloading ramp
8.3.6 Thread missing fault
8.3.7 Tying failures
8.4 Electrical/electronic installation
8.4.1 Electrical circuit faults
9 Maintenance
9.1 General maintenance instructions
9.1.1 Maintenance and safety tips
9.1.2 Wheels and tires
9.1.3 Brakes
9.1.4 Hydraulic circuit
9.1.5 Chains
9.1.6 Crimping and tying device
9.1.7 Cardan shaft
9.1.8 Hitch
9.1.9 Cutting device
9.1.10 Protection devices
9.1.11 Screws and nuts
9.1.12 Lubrication and greasing
9.1.13 Inductive sensors
9.1.14 Welding work
9.1.15 Spare parts
9.2 Lubricant tables
9.2.1 Lubricants
9.3 Maintenance tables
9.3.1 Maintenance operations before harvest
9.3.2 Maintenance operations after the first 10 hours of service
9.3.3 Maintenance operations after the first 50 hours of service
9.3.4 Maintenance operations after the first 100 hours of service
9.3.5 Maintenance operations after the first 250 hours of service
9.3.6 Maintenance operations every 5 hours of service or every day
9.3.7 Maintenance operations every 10 hours of service or every day
9.3.8 Maintenance operations every 50 hours of service
9.3.9 Maintenance operations every 100 hours of service
9.3.10 Maintenance operations every 250 hours of service
9.3.11 Maintenance operations every 15,000 bales
9.3.12 Annual maintenance operations or every 500 hours of service
9.3.13 Maintenance operations if necessary
9.4 Basic settings
9.4.1 Initial calibration of the baler
9.4.2 Counterblades
Bedknife adjustment
9.5 Gear maintenance operations
9.5.1 Main drive box
9.5.2 Fixing the main drive box
9.5.3 Elastomeric damping stops
9.5.4 Rudder angle transmission box
9.5.5 Feeder drive box
9.5.6 Top rotor angle transmission
9.5.7 Rotor and pick-up drive box
9.5.8 Knotter drive box
9.5.9 Flywheel brake
9.6 Maintenance operations on the clutch
9.6.1 Freewheel Friction Clutch
9.6.2 Main drive locking screw
9.7 Axle and wheel maintenance operations
9.7.1 Single axis
9.7.2 Tandem axle
9.7.3 Tracking tandem axle
9.7.4 Wheel tightening check
9.7.5 Replacing the wheels
9.7.6 Wheel hub
9.7.7 Tire check
9.8 Brake maintenance operations
9.8.1 Hydraulic and active hydraulic braking
9.8.2 Pneumatic braking
9.8.3 Replacing the brake linings
9.9 Hydraulic system maintenance operations
9.9.1 Hydraulic tank
9.9.2 Hydraulic pressure accumulator
9.10 Pick-up maintenance operations
9.10.1 Double worm screw pick-up (depending on equipment)
9.10.2 Pick-up with through worm screw (depending on equipment)
9.11 Tying maintenance operations
9.11.1 Start manual tying
9.11.2 Needles
Needle height
High dead center of the needles:
Needles – piston position:
Check the needle/piston position
Modify the position of the knotter drive box
Modify the position of the cardan shaft
Checking Piston Safety Timing
Fork adjustment (12)
Replacing a needle
Needle brake:
9.11.3 Replacing the needle brake plates
Remove a needle brake
Disassembling a needle brake
Install a needle brake
Install a needle brake
9.11.4 Thread tensioner adjustment
9.11.5 Knotter settings
9.11.6 Tying actuator
9.11.7 Knotter shaft security screw
9.11.8 Replacing the knotter brake plates
Remove the brake from the knotters
Remove the brake from the knotters
Install the knotter brake
9.12 Hitch device maintenance operations
9.12.1 Checking the attachment hole fixation
9.12.2 Checking the rudder head fixation
9.13 Maintenance operations of the centralized lubrication system
9.13.1 Manual centralized lubrication (option)
9.13.2 Automatic centralized lubrication (option)
9.14 Greasing scheme
9.14.1 Greasing intervals
9.14.2 Cardan shaft
9.14.3 Greasing points – 5 h
9.14.4 Greasing points – 10 h
9.14.5 Greasing points – 50 h
9.14.6 Grease points – 100 h
9.14.7 Grease points – 250 h
9.15 Hibernation
9.15.1 General information
9.15.2 Cleaning
9.15.3 Greasing
9.15.4 Maintenance
9.15.5 Storage
10 Decommissioning and waste disposal
10.1 General data
10.1.1 Decommissioning and waste disposal
11 EC declaration of conformity
11.1 General data
11.1.1 Declaration of conformity for CE
00 0295 168 6.pdf:
QUADRANT 2200 Advantage RotoFeedQUADRANT 2200 Advantage RotoCut
1 Regarding this instruction manual
1.1 General data
1.1.1 Validity of the manual
1.1.2 About this user manual
1.1.3 Technical characteristics
2 Security
2.1 General data
2.1.1 General information
2.1.2 Authorized use
2.1.3 Reasonably foreseeable misuse
2.1.4 Safety regulations
2.1.5 Symbols applicable to danger indications
2.1.6 Highway driving
2.1.7 Accident prevention
2.1.8 Waste disposal
2.1.9 Residual risks
2.2 Graphic danger symbols
2.2.1 Description
2.2.2 Location of safety stickers
2.3 Safety equipment
2.3.1 Signal lighting
2.3.2 Reflective equipment
2.3.3 Surety
2.3.4 Chocks
2.3.5 Parking brake
2.3.6 Flywheel brake
2.3.7 Locking the pick-up
2.3.8 Locking the bale exit ramp
3 Machine Description
3.1 Existing models
3.1.1 Designation of machines
3.2 Overview and functions
3.2.1 Left side
3.2.2 Right side
3.3 Work and service positions
3.3.1 General information
3.3.2 Front of the baler
3.3.3 Top of the baler
3.4 Identification plate and serial number
3.4.1 Spare parts and technical information
3.4.2 Position of the nameplates
3.4.3 Machine nameplate
3.4.4 Rudder nameplate
3.5 General operating principle
3.5.1 Bale pressing cycle
3.6 Control terminal
3.6.1 Control terminal
3.6.2 ISOBUS connection
3.7 Transmission and drive
3.7.1 Power transmission
3.7.2 Friction clutch
3.7.3 Main drive
3.7.4 Rotor drive
3.7.5 Feeder drive
3.7.6 Knotter operation
3.8 Reception of the harvest
3.8.1 Pick-up
3.8.2 Reducing rollers
3.8.3 Short straw plank
3.9 Power set
3.9.1 Rotor
3.9.2 RotoCut cutting device (optional)
3.9.3 Carrier
3.10 Pressing system
3.10.1 Piston and pressing channel
3.11 Tying system
3.11.1 Tying process
3.11.2 Thread compartments
3.11.3 Thread shortage indicator
3.11.4 Needles
3.11.5 Knotters
3.11.6 Turbofan
3.12 Unloading bales
3.12.1 Control block
3.12.2 Bale unloading ramp
3.12.3 Bale unloading ramp position detector (optional)
3.12.4 Bale unloading sensor (optional)
3.12.5 Humidity sensor (optional)
3.12.6 Bale ejector
3.13 Centralized lubrication
3.13.1 General information
3.13.2 Manual centralized lubrication
3.13.3 Automatic centralized lubrication
3.13.4 Supplementary lubrication
3.14 Axis
3.14.1 General information
3.14.2 Single axis
3.14.3 Tandem axle
3.14.4 Tracking tandem axle
3.15 Service brake
3.15.1 General information
3.15.2 Pneumatic braking
3.15.3 Hydraulic braking
3.15.4 Active hydraulic braking
3.16 Hydraulic system
3.16.1 Hydraulic oil tank
3.17 Equipment
3.17.1 Ladder
3.17.2 Front ladder support
3.17.3 Stirrup
3.17.4 Electronic module
3.17.5 12 V socket
4 Control and display instruments
4.1 CLAAS Medium Terminal
4.1.1 Presentation
4.1.2 Screen
4.1.3 Key identification
4.1.4 Home page
4.1.5 Description of the menus
4.2 ISOBUS terminal
4.2.1 Presentation
4.2.2 General information
4.2.3 Screen
4.2.4 Description of the menus Using the ISOBUS terminal
5 Technical data
5.1 Baler
5.1.1 General information
5.1.2 Dimensions
5.1.3 Weight
5.1.4 Hooking
5.1.5 Cardan shaft
5.1.6 Feeding and pressing
5.1.7 Tying device
5.1.8 Wheels
5.1.9 Hydraulic circuit
5.1.10 Screw tightening torques
5.1.11 Braking
5.1.12 Speed - Brake/Axis Type
5.1.13 Greasing and lubrication
5.1.14 Sound levels
5.2 Safety devices
5.2.1 Security screw
5.2.2 Overload safety
5.3 Tractor
5.3.1 Required power
5.3.2 PTO
5.3.3 Hookup
5.3.4 Electrical connections
5.3.5 Hydraulic connections
5.3.6 Hydraulic circuit and oil
5.3.7 Braking
6 Preparation of the machine
6.neral data
6.1.1 First commissioning
6.1.2 Equipment control
6.2 Cardan shaft
6.2.1 Safety regulations
6.2.2 Cardan shafjustment
6.2.3 Adaptation of the cardan shaft length
6.2.4 Transformation kit, 8 grooves (optional)
6.2.5 Double-joint wide-angle gimbal
6.2.6 Positioning the cardan shaft
6.3 Trailer support
6.3.1 Recommendations
6.3.2 Types of fixing
6.3.3 Hitch fixing
6.3.4 Adaptation of the fork hitch/oscillating bar hitch
6.3.5 Hitching the baler to the tractor
6.3.6 Positioning the cardan shaft
6.4 Hydraulic connections
6.4.1 Location of flexible ducts
6.4.2 Sear and pick-up
6.4.3 General hydraulics of the baler
6.5 Electrical connections
6.5.1 Marking of electrical cables
6.5.2 Lights
6.5.3 Battery cable (optional)
6.5.4 Power supply to the CLAAS Medium Terminal and the baler
6.5.5 Baler power supply with ISOBUS cable
6.6 Service brake
6.6.1 Hydraulic brake
6.6.2 Active hydraulic brake
6.6.3 Air brake
6.7 Tied
6.7.1 Yarn quality
6.7.2 Preparation
6.7.3 Thread tensioner adjustment
6.7.4 Thread placement
6.7.5 Placing the thread in the knotters
Manual activation of a bundle
Baler equipped with mechanical tying activation
Baler equipped with electric tying activation
6.7.6 Checking the settings
6.8 Cutting device
6.8.1 Safety regulations
6.8.2 Control
6.8.3 Placing the blades
6.8.4 Assembly of false blades (optional)
6.8.5 Unused blades and dummy blades
6.9 Machine loading
6.9.1 Lifting the baler
6.9.2 Baler stowage
7 Management
7.1 General data
7.1.1 Baler user
7.1.2 Opening doors and casings
7.2 Movements with the baler
7.2.1 Equipment control
7.2.2 Preparations for transportation
7.2.3 Road travel
7.2.4 Arrival at the field
7.2.5 Moving around the field
7.2.6 Parking
7.3 Before each use
7.3.1 Reminders
7.3.2 Cardan shaft
7.3.3 Baler maintenance
7.4 Commissioning in the field
7.4.1 Usage tips
7.4.2 Commissioning of the machine
cardan shaft
Material transfer system
After a machine stop
7.4.3 Bale unloading ramp
Manual bale unloading ramp
Hydraulic bale unloading ramp
7.4.4 Bale ejector (option)
7.4.5 Tracking axis (option)
7.5 Pick-up
7.5.1 Important
7.5.2 Pick-up wheels
7.5.3 Pick-up height
7.5.4 Reducing rollers
7.6 Cutting device
7.6.1 RotoCut cutting device (optional)
7.7 Bale parameters
7.7.1 Bale adjustments
Bale length adjustment
Baler equipped with mechanical tying activation
Baler equipped with electric tying activation
7.8 CLAAS Medium Terminal
7.8.1 Pressing pressure (RotoCut option)
7.8.2 Activation / deactivation of the blades (RotoCut option)
7.8.3 Cutting frame (RotoCut option)
7.8.4 Counters Menu (RotoCut option)
7.8.5 Faults
7.8.6 Pressing process
7.8.7 Manual activation of the tying process (optional)
7.8.8 Automatic lubrication (depending on equipment)
7.8.9 Bale length adjustment
7.8.10 Sound
7.9 ISOBUS terminal
7.9.1 Pressing pressure (RotoCut option)
7.9.2 Activation / deactivation of the blades (RotoCut option)
7.9.3 Cutting frame (RotoCut option)
7.9.4 Counters Menu
Maintenance indicator reset
7.9.5 Faults
7.9.6 Pressing process
7.9.7 Manual activation of the tying process (optional)
7.9.8 Automatic lubrication
7.9.9 Bale length adjustment
7.10 Unclogging the baler
7.10.1 How to avoid traffic jams?
7.10.2 Safety regulations
7.10.3 Pick-up jam
7.10.4 Jam of the reduction rollers
7.10.5 Feed rotor jam (RotoFeed option)
Rotor unclogging
7.10.6 Cutting rotor jam (RotoCut option)
7.11 After use
7.11.1 Reminders
7.11.2 Baler protection
7.11.3 Disconnecting the baler
7.11.4 Daily checks
7.11.5 Daily cleaning
8 Incident and solution
8.1 Tied
8.1.1 Origin of tying problems
8.1.2 Resolution of tying problems
8.2 Centralized lubrication
8.2.1 Resolution of centralized lubrication problems
8.3 CLAAS Medium Terminal
8.3.1 Faults displayed on the control terminal
8.3.2 Electrical circuit
8.3.3 PTO failure
8.3.4 Transfer system
8.3.5 Bale unloading ramp
8.3.6 Thread missing fault
8.3.7 Tying failures
8.4 ISOBUS terminal
8.4.1 Electrical circuit
8.4.2 Main drive and system
8.4.3 Transfer system
8.4.4 Bale unloading ramp
8.4.5 Lack of thread
8.4.6 Tying failures
8.5 Electrical/electronic installation
8.5.1 Electrical circuit faults
9 Maintenance
9.1 General maintenance instructions
9.1.1 Maintenance and safety tips
9.1.2 Wheels and tires
9.1.3 Brakes
9.1.4 Hydraulic circuit
9.1.5 Chains
9.1.6 Crimping and tying device
9.1.7 Cardan shaft
9.1.8 Hitch
9.1.9 Cutting device
9.1.10 Protection devices
9.1.11 Screws and nuts
9.1.12 Lubrication and greasing
9.1.13 Inductive sensors
9.1.14 Welding work
9.1.15 Spare parts
9.2 Lubricant tables
9.2.1 Lubricants
9.3 Maintenance tables
9.3.1 Maintenance operations before harvest
9.3.2 Maintenance operations after the first 10 hours of service
9.3.3 Maintenance operations after the first 50 hours of service
9.3.4 Maintenance operations after the first 100 hours of service
9.3.5 Maintenance operations after the first 250 hours of service
9.3.6 Maintenance operations every 5 hours of service or every day
9.3.7 Maintenance operations every 10 hours of service or every day
9.3.8 Maintenance operations every 50 hours of service
9.3.9 Maintenance operations every 100 hours of service
9.3.10 Maintenance operations every 250 hours of service
9.3.11 Maintenance operations every 15,000 bales
9.3.12 Annual maintenance operations or every 500 hours of service
9.3.13 Maintenance operations if necessary
9.4 Basic settings
9.4.1 Initial calibration of the baler
9.4.2 Counterblades
Bedknife adjustment
9.5 Gear maintenance operations
9.5.1 Main drive box
9.5.2 Fixing the main drive box
9.5.3 Elastomeric damping stops
9.5.4 Rudder angle transmission box
9.5.5 Feeder drive box
9.5.6 Top rotor angle transmission
9.5.7 Rotor and pick-up drive box
9.5.8 Knotter drive box
9.5.9 Flywheel brake
9.6 Maintenance operations on the clutch
9.6.1 Freewheel Friction Clutch
9.6.2 Main drive locking screw
9.7 Axle and wheel maintenance operations
9.7.1 Single axis
9.7.2 Tandem axle
9.7.3 Tracking tandem axle
9.7.4 Wheel tightening check
9.7.5 Changing the wheels
9.7.6 Wheel hub
9.7.7 Tire check
9.8 Brake maintenance operations
9.8.1 Hydraulic and active hydraulic braking
9.8.2 Pneumatic braking
9.8.3 Replacing the brake linings
9.9 Hydraulic system maintenance operations
9.9.1 Hydraulic tank
9.9.2 Hydraulic pressure accumulator
9.10 Pick-up maintenance operations
9.10.1 Double worm screw pick-up (depending on equipment)
9.10.2 Pick-up with through worm screw (depending on equipment)
9.11 Tying maintenance operations
9.11.1 Start manual tying
9.11.2 Needles
Needle height
High dead center of the needles:
Needles – piston position:
Check the needle/piston position
Modify the position of the knotter drive box
Modify the position of the cardan shaft
Checking Piston Safety Timing
Fork adjustment (12)
Replacing a needle
Needle brake:
9.11.3 Replacing the needle brake plates
Remove a needle brake
Disassembling a needle brake
Install a needle brake
Install a needle brake
9.11.4 Thread tensioner adjustment
9.11.5 Knotter settings
9.11.6 Tying actuator
9.11.7 Knotter shaft security screw
9.11.8 Replacing the knotter brake plates
Remove the brake from the knotters
Remove the brake from the knotters
Install the knotter brake
9.12 Hitch device maintenance operations
9.12.1 Checking the attachment hole fixation
9.12.2 Checking the rudder head fixation
9.13 Maintenance operations of the centralized lubrication system
9.13.1 Manual centralized lubrication (option)
9.13.2 Automatic centralized lubrication (option)
9.14 Greasing scheme
9.14.1 Greasing intervals
9.14.2 Cardan shaft
9.14.3 Greasing points – 5 h
9.14.4 Greasing points – 10 h
9.14.5 Greasing points – 50 h
9.14.6 Grease points – 100 h
9.14.7 Grease points – 250 h
9.15 Hibernation
9.15.1 General information
9.15.2 Cleaning
9.15.3 Greasing
9.15.4 Maintenance
9.15.5 Storage
10 Decommissioning and waste disposal
10.1 General data
10.1.1 Decommissioning and waste disposal
11 EC declaration of conformity
11.1 General data
11.1.1 Declaration of conformity for CE
11.1.2 Declaration of conformity for CE
Claas Operator Manual PDF
Claas QUANTUM 6800-4500 GT P (615) Loader Wagons Operator Manual DE
Claas Operator Manual PDF
Claas Operator Manual PDF
![](https://automanual.net/wp-content/uploads/2024/04/claas-quadrant-2200-advantage-756-baler-operator-manual-es-1.jpg)