File List:
00 0288 572 0.pdf
00 0292 957 3.pdf
00 0300 747 0.pdf
00 0301 487 0.pdf
00 0288 572 0.pdf:
TUCANO 580 / 570 / 560TUCANO 450 / 440 / 430 / 420TUCANO 430 MONTANA 4TUCANO 340 / 320
Contents
Maintenance
Overview of maintenance frequencies
Maintenance intervals
Validity of the notice
Lubricants
To be carried out before the first commissioning
Before the start of the harvest
Every 1000 operating hours
Check hopper drain gearbox oil level
Change hopper drain gearbox oil
Drain the oil
Pour the oil
00 0300 747 0.pdf:
TUCANO 430 MONTANA 4
Contents
1 About this user manual
1.1 Notes regarding the instructions
1.1.1 Validity of the notice
2 Security
2.1 Safety marking on the machine
2.1.1 Undercarriage warning pictograms
2.1.2 Power group warning pictogram
2.2 Safety devices
2.2.1 Install the safety supports on the variable height chassis
2.2.2 Remove the safety supports from the variable height chassis
3 Description of the machine
3.1 Overview and mode of operation
3.1.1 Overview of the MONTANA 4 height-adjustable chassis, front left
3.1.2 Overview of the MONTANA 4 height-adjustable chassis, rear right side
3.1.3 Operating mode of the MONTANA 4 height-adjustable chassis
3.2 Machine information
3.2.1 Variable height chassis stickers
4 Controls and displays
4.1 Cabin and driving position
4.1.1 Control console with
4.1.2
5 Technical characteristics
5.1 TUCANO 430 MONTANA 4
5.1.1 Mercedes-Benz OM 936 LA.E4 diesel engine
5.1.2 Variable height chassis
5.1.3 Tire pressure
5.1.4 Overview of drive axle track gauge
5.1.5 Steering axle track gauge overview
5.1.6 Track gauge table 01
5.1.7 Track gauge table 02
5.1.8 Track gauge table 03
5.1.9 Turning diameter
Measurement conditions
5.1.10 Hopper volume
5.1.11 Dimensions of the hopper discharge tube in working position
5.1.12 Machine dimensions
5.1.13 Machine weight
Machine weight
Weight of options
5.2 Operating consumables
5.2.1 Lubricants
5.2.2 Hydraulic oils
6 Preparing the machine
6.1 Disconnect and secure the machine
6.1.1 Disconnect and secure the machine
6.2 Enter work and maintenance stations
6.2.1 Unfold the front ladder steps
6.2.2 Enter the maintenance station of the right side driving position
Enter the maintenance station of the right side driving position
6.3 Before commissioning
6.3.1 To be carried out before the first commissioning
6.4 Prepare the machine for driving
6.4.1 Prepare for road travel
6.4.2 Prepare for movement in the field
6.5 Adjusting the machine for work
6.5.1 Set the machine to harvest corn
6.5.2 Set the corn harvest machine to cereal harvest
6.6 Power group
6.6.1 Check the anti-slip belts of the conveyor
6.6.2 Adjust the height of the feed chains
6.7 Chassis
6.7.1 Learning the MONTANA 4 end stops
6.8 Threshing bodies
6.8.1 Install the final counter-batten*
6.9 Separation
6.9.1 Install and remove the shaker cover plate*
6.10 Grain recovery
6.10.1 Getting in and out of the shaker compartment through the hopper
6.11 Assembly parts and bodywork
6.11.1 Place the weight on the machine
7.1 Driving the machine
7.1.1 Operating the machine
Move the machine forward
Brake the machine
Stop the machine
Move the machine in reverse
7.1.2 Park the machine
7.2 Chassis
7.2.1 Checking the functions of the MONTANA 4
Controlling MONTANA 4 functions on level ground
Check the operation of the MONTANA 4 on slopes
7.2.2 Bring the machine to neutral position
7.2.3 Connecting and disconnecting MONTANA 4 automatic mode
Connect automatic mode MONTANA 4
Disconnect automatic mode MONTANA 4
7.2.4 Connect the MONTANA 4 hand control
7.2.5 Connect 4-TRAC
Connect 4-TRAC manual mode
Connect 4-TRAC automatic mode
7.2.6 Disconnect 4-TRAC
7.2.7 Towing the machine
7.3 Brake
7.3.1 Coupling and uncoupling the brake pedals
7.4 Power group
7.4.1 Adjust the feed fingers
8 Maintenance
8.1 Overview of maintenance frequencies
8.1.1 Before the start of the harvest
8.1.2 After the first 100 hours of operation
8.1.3 Every 10 operating hours or daily
8.1.4 Every 50 operating hours
8.1.5 Every 100 operating hours
8.1.6 Every 500 hours of service or annually
8.2 Lubrication plan
8.2.1 Grease the left side lubrication points every 10 operating hours
8.2.2 Grease the right side lubrication points every 10 operating hours
8.2.3 Lubricate the left side lubrication points every 100 operating hours
8.2.4 Grease the right side lubrication points every 100 operating hours
8.3 Chassis
8.3.1 Check the oil level in the drive axle axle box
8.3.2 Replace the oil in the drive axle axle box
Drain the oil
Pour the oil
8.3.3 Check the oil level of the drive axle gearbox
8.3.4 Replace the drive axle gearbox oil
Drain the oil
Pour the oil
8.4 Brake
8.4.1 Cleaning the brake
8.5 Workouts
8.5.1 Setting MONTANA 4 drives
8.5.2 Remove the belt (R01)
8.5.3 Install the belt (R01)
8.5.4 Adjust the belt (R01)
8.5.5 Remove the chain (K30)
8.5.6 Install the chain (K30)
8.5.7 Adjust the chain (K30)
8.5.8 Remove the chain (K60)
8.5.9 Install the chain (K60)
8.5.10 Adjust the chain (K60)
8.6 Hydraulic system
8.6.1 Check the hydraulic oil level
8.6.2 Replacing the hydraulic oil
Drain the oil
Pour the oil
8.7 Power group
8.7.1 Adjusting the feed chains
8.7.2 Adjusting the swivel frame
00 0301 487 0.pdf:
TUCANO 580 / 570TUCANO 450 / 440 / 430 / 420TUCANO 430 MONTANA 4TUCANO 340 / 320
Contents
1 Introduction
1.1 General information
1.1.1 Validity of the notice
2 Technical characteristics
2.1 Operating consumables
2.1.1 Lubricants
3 Maintenance
3.1 Threshing bodies
3.1.1 Check the oil level of the beater reduction gearbox*
Claas Operator Manual PDF