File List:
00 0290 143 2.pdf
00 0292 437 0.pdf
00 0292 634 0.pdf
00 0292 903 0.pdf
00 0299 846 1.pdf
00 0300 374 1.pdf
00 0303 568 0.pdf
00 0299 846 1.pdf:
Introduction
Introduction
Table of contents
Table of contents
General Information
Vehicle type approval
Important information
Identification plate / Serial number
Safety rules
Safety rules
Safety locks
Feed rake safety locks
Reel safety lock
Safety decals with pictorials
Specifications
Weights / Dimensions / Safety devices
Additional weights
Prior to operation
Carry out prior to initial operation
Driving lights / Cutterbar cylinder
Driving lights for road use
Changing the driving lights (up to serial no. …)
Changing the driving lights (from serial no. …)
Safety lighting rail on the cutterbar
Removing the transport fixtures
Third cutterbar cylinder
Adjusting the cutterbar floatation springs
Accessory equipment
Additional headlights
Fitting the switches and the additional headlights
Installing the push buttons for switching
Mounting the additional headlights on both sides
Adjusting the additional headlights
Operation
Cutterbar skids
Adjusting the cutterbar skids
Cutting angle adjustment
Adjusting the cutting angle
Mounting the spacer bar
Mounting the coupling brackets
Locking the coupling lug after fitting the cutterbar
Unlocking the coupling lug before removing the cutterbar
Mounting the shaft extension
Mounting the extension to the intermediate drive shaft (LEXION 530 – 510)
Fitting the cutterbar
Tilting the cutterbar from the transport position
Installing and removing the cutterbar
Installing the cutterbar when folded in (cutterbar in the transport position)
Locking the cutterbar at top and bottom on both sides
Connecting the universal coupling
Changing the cutterbar from transport position to working position
Fitting the universal drive shafts LEXION MONTANA (from serial no. 71300231)
Removing standard universal drive shafts
Installing the universal drive shaft for LEXION MONTANA
Changing the cutterbar from working position to transport position
Aligning the cutterbar / removing the cutterbar
Aligning the cutterbar (machines without Auto-Contour)
Removing the cutterbar
Adjustments on the cutterbar
Crop dividers
Outer deflector
Adjusting the dividers
Crop lifters
Removing the knife
Installing the knife
Adjusting the knife height
Aligning the knife clips
Spare knife
Adjusting the reel height
Fine height adjustment of the reel
Reel drive
Reel fore and aft adjustment
Feed auger
Adjusting the clearance to the cutterbar bottom plate
Height adjustment of the feed auger
Adjusting the intake finger position
Safety feature
Cutterbar skids
Malfunction, possible cause and/or remedy
Maintenance
Maintenance schedules and lubricants charts
Maintenance schedule
Lubricants chart
Transmissions
Knife drive transmission
Spring-loaded cylinders / Drive chains / Inductive sensors
Adjusting the spring-loaded cylinders for knife drives
Tensioning the drive chains
Tensioning the reel drive chain
Cleaning the guide rails of the locking cylinder
Aligning the double fingers
Adjusting the reel limit switch
Adjusting the locking pawl at the centre reel guide
Cleaning the spaces of the supporting arm bearings
Cleaning the coupling lug areas
Suggestions for winter storage
Lubrication chart
Lubricants and notes
Claas Assembly Instruction PDF
Claas LEXION 630 MONTANA (C52) Combine Assembly Instruction DE
Claas Assembly Instruction PDF
Claas Assembly Instruction PDF
Claas Assembly Instruction PDF
Claas Assembly Instruction PDF
Claas Assembly Instruction PDF
Claas Assembly Instruction PDF
Claas Assembly Instruction PDF
![](https://automanual.net/wp-content/uploads/2024/04/claas-c540-c450-rabatabil-lexion-706-combines-assembly-instruction-en-1.jpg)