Claas Talos 240-210 (A39) Tractors Repair Manual EN

File List:

00 1145 868 0.pdf
00 1150 411 1.pdf

00 1145 868 0.pdf:

TALOS 240-230-220-210
Table of contents
Introduction
General Information
Using the repair manual
Scope of the repair manual
General repair instructions
Technical specifications
Cause of damage
Spare parts
Diesel engine
Generator
Welding work
Drive belt/drive chains
Tapered ring assemblies
Self-locking bolts with microencapsulated glue
Threadlock
Lock collar bearing
Collet bearing
Screwed unions with cutting rings on the hydraulic pipes
Progressive ring bolt connectors on hydraulic pipes
Double flare unions screwed onto the hydraulic pipes
Flexible hydraulic hoses
Advice for economical repairs
Torque settings
Standardised tightening torques for metric threaded screws
Tightening torques for DIN 3865 hydraulic unions
Technical specifications
Lubricants
CCN explanation
CCN (CLAAS Component Number)
Electric system standard
Overview
Hydraulic system standard
Overview
CCN Index
General Information
Important note
Identification of warning and danger signs
General Safety and Accident Prevention Regulations
Leaving the machine
Adjusting and maintenance work
Risk of injury through hydraulic liquid
Air conditioner
Hydraulic accumulators
First aid measures
Battery isolating switch
Jacking up the machine
Putting the machine out of operation
01 Engine
0102 Complete component
Introduction
General notes
General notes on the electrical circuit
Conversion between the main units of measurement of the international system and the units derived from current usage
General points
Engine views – TALOS 210-220-230
General engine service
Special tool
General features
Assembly play
Tightening torques
Engine peripherals – TALOS 210-220-230
Removing/refitting the engine peripherals
Engine peripherals – TALOS 240
Removing/refitting the engine peripherals
0110 Engine housing
Separating the engine from the clutch housing
0115 Engine unit
Repairing the cylinder block
Checks and measurements
Removing the connecting rods / pistons / crankshaft and camshaft – TALOS 210-220- 230
Crankshaft – TALOS 210-220-230
Measuring the journals and crank pins
Fitting the crankshaft bearings
Refitting the crankshaft
Checking the crankshaft axial play
Connecting rod/piston assembly – TALOS 210-220-230
Special tool
Piston pin
Conditions required for correct coupling of the pin and piston
Connecting rods
Fitting the connecting rod/piston assembly – Coupling the connecting rod/piston
Fitting the piston rings
Fitting the connecting rod/piston assemblies in the liners
Fitting the connecting rod caps and crank pins
Piston protrusion measurement
Balancing system using counter-rotating weights – TALOS 210-220-230
Removing the connecting rods / pistons / crankshaft and camshaft – TALOS 240
Crankshaft – TALOS 240
Measuring the journals and crank pins
Replacing the oil pump control drive pinion
Fitting the crankshaft bearings
Refitting the crankshaft
Checking the crankshaft axial play
Connecting rod/piston assembly – TALOS 240
Special tool
Piston pin
Conditions required for correct coupling of the pin and piston
Connecting rods
Fitting the connecting rod/piston assembly – Coupling the connecting rod/piston
Fitting the piston rings
Fitting the connecting rod/piston assemblies in the liners
Fitting the connecting rod caps and crank pins
Piston protrusion measurement
0120 Cylinder head / Valves / Idler gear
Timing – TALOS 210-220-230
Special tools
Camshaft
Checking the cam lift and the alignment of the shaft cylinders
Replacing the rings
Pushrods
Fitting the pushrods – Camshaft
Cylinder head – TALOS 210-220-230
Special tools
Removing the valves
Checking the cylinder head supporting surface
Valve guide
Valve seats
Fitting the cylinder head
Timing – TALOS 240
Special tools
Camshaft
Checking the cam lift and the alignment of the shaft cylinders
Replacing the rings
Pushrods
Fitting the pushrods – Camshaft
Cylinder head – TALOS 240
Special tool
Removing the valves
Checking the cylinder head sealing
Checking the cylinder head supporting surface
Valve guide
Valve seats
Valve springs
Fitting the cylinder head
0125 Injection – / Fuel system
Fuel supply – TALOS 210­220­230
General points
Schematidgram
Hose diagram
Operating principle
Injection pump
Injection system – TALOS 210-220-230
Special tools
Removing/refitting the injection pump
BOSCH VE 4/12 F pump
Checking the static advance of the injection pump on the engine at top dead centre on cylinder 1
Fuel supply – TALOS 240
General points
Hose diagram
Operating principle
Injection pump
Priming pump
Fuel filter
Injection system – TALOS 240
Special tools
Removing/refitting the injection pump
0130 Lubricating oil system
Engine lubrication – TALOS 210-220-230
Oil pump
Oil vapour recycling
Removing the blow-by on the cylinder head cover
Refitting the blow-by
Oil pressure switch
Engine lubrication – TALOS 240
Oil vapour recycling
Oil pressure switch
0135 Cooling system
Cooling system – TALOS 210­220­230
Description
Water pump
Thermostat
Coolant temperature sensor
ola temperature sensor for KSB
Heat exchanger
Cooling system – TALOS 240
Description
Coolant temperature sensor
Coolant temperature sensor for KSB
Solenoid on supply pump
0145 Air intake
Turbocharging – TALOS 210-220-230
Turbocharging – TALOS 240
Cold starting assistance – TALOS 240
Preheating resistor
0165 Exhaust gas treatment
External EGR – TALOS 210-220-230
Operation
Air temperature and pressure sensor
EGR solenoid valve
02 Gearbox / Clutch / Universal drive shaft
0202 Complete component
Transmission general view
Removing/refitting the transmission
Transmission inspection
Transmission – Cross-sectional view
Tightening torques
Separating the clutch housing from the central casing
Separating the central casing from the rear axle casing
0215 Mechanical clutch
Clutch inspection and repair
Special tools
Description
Clutch – Cross-sectional view
Faults and solutions
Removing the clutch housing
Separating the clutch from the shock absorber
Clutch disc inspection
Refitting the clutch disc and the shock absorber
Refitting the clutch and the shock absorber
Removing the clutch release fork and bearing
Clutch release bearing inspection and fitting
Clutch and brake fluid level
Bleeding the clutch
0218 Clutch control
Clutch master cylinder and lever
Clutch pedal
Setting the clutch pedal
Setting the clutch pedal pressure
0220 Mechanical reverser
Description
Mechanical reverser – Cross-sectional views
Drive train
Removing the reverser
0222 Hydraulical reverser
PSS reverser
PSS reverser assembly – Cross-sectional view
Faults and solutions
PSS reverser – Cross-sectional view
PSS reverser – General view
PSS reverser assembly – Cross-sectional view
PSS reverser – Views
Removing the PSS reverser
Removing the reverse idler gear
Remove the clutch housing cover
PSS reverser hydraulic components
PSS reverser hydraulic hoses
PSS reverser control valve
Cleaning the PSS reverser filter
0228 Reverser control
Reverser lever
Reverser lever – Cross-sectional view
Mechanical reverser control
Mechanical reverser control – Cross-sectional view
View of reverser synchro and associated parts
Removing the mechanical reverser synchro
Checking for wear on the reverser synchro
PSS hydraulic reverser control
Description
Drive train
0230 Mechanical gearbox
Gearbox – Cross-sectional view
Removing the power take-off clutch and the gearbox
Range box
Range box – Cross-sectional views
Removing the gearbox
Creeper range (depending on equipment)
Creeper range assembly – Cross-sectional view
Removing the creeper range
0238 Gearbox control
Gear lever
Description
Gear lever – Cross-sectional view
Drive train
Range selector lever
Operation
Range selector lever – Cross-sectional view
3rd range operation (H)
Drive train
Creeper range control lever
Cross-sectional view
Operation
Drive train
0240 Rear axle housing
Repairing the axle tubes
Axle tube – Cross-sectional views
Removing the axle tube
0242 Differential
Rear differential locking system
Special tools
Rear differential lock – General view
Description
Removing the rear differential
Rear differential lock hydraulic device
Removing the drive pinion shaft
Refitting the drive pinion shaft
Setting the clearance between the teeth and the drag torque
0252 Electro-hydraulical front axle drive
4-wheel drive transmission
4-wheel drive transmission – Cross-sectional view
Operation
4-wheel drive transmission components
03 Chassis
0325 Driven steering axle, front
Front axle general view
View of the front axle
Tightening torques
Removing/refitting the front axle
Separating the front axle
View of the complete coupling bar
Adjusting and refitting the coupling bars
Repairing the wheel reduction gear
Wheel reduction gear – Cross-sectional view
Description
Wheel hub components
Repairing the wheel hub
Front axle differential
Front axle and drive pinion differential – Cross- sectional view
Repairing the front axle differential
04 Brake
0405 Service brake
Service brakes
Service brake system components
Rear brakes
Removing the service brakes
Cross-sectional view of the brake mechanism
Bleeding the brake hydraulic circuit
Adjust the brake pedal clearances
0415 Parking brake
Handbrake:
Handbrake components
Operation
Removing the handbrake
05 Steering
0505 Steering
General view of the steering system
Steering system components
Steering operating diagram – Neutral position
Oil flow diagram – Turned to the right/Turned to the left
Faults and solutions
Repairing the steering gearbox
Steering gearbox – Exploded view
Removing the steering gearbox
Repairing the steering gearbox
Inspection and refitting
06 Lift device
0605 Rear power lift
Rear hydraulic lifting system
CAN bus diagram
Rear hydraulic linkage electronic control system sensors
Electronic control for rear hydraulic linkage (multifunction armrest)
User controls
Hydraulic linkage cover
Cross-sectional views
Tightening torques
Removing the linkage cover
Linkage control valve
Cross-sectional view
Hydraulic diagram
Throughput adjustment
Proportional solenoid valves
Calibrating the lower linkage stop
Adjusting the upper connecting rod
Calibrating the position control lever lower limit
Setting the power take-off automatic disengagement point
08 Drives
0802 Rear PTO
Rear power take-off system
Power take-off proportional to ground speed
User controls
Removing the power take-off proportional to ground speed
Rear power take-off system – View of components
Rear power take-off speed selector lever
Power take-off speed selection – Cross-sectional view
Removing the rear power take-off
09 Hydraulic system
0915 Hydraulic lines
Description of the hydraulic system
Special tools
Hydraulic components
Hydraulic circuit components
Hydraulic system diagram (mechanically controlled linkage)
Hydraulic system diagram (electrohydraulically controlled linkage)
Low pressure circuit
Transmission electrohydraulic control block
Electrohydraulic control block diagram
Hydraulic clutch
Service brakes
Independent power take-off clutch – Cross- sectional view
Oil cooler bypass
0920 Valves
Auxiliary spool valves
Auxiliary spool valve control levers
Quick connections
Front electrohydraulic block and controls (depending on equipment)
Front electrohydraulic block
Operation of the multifunction lever
Multifunction lever assembly – electrohydraulic block
Hydraulic diagrams
10 Electrical / Electronic equipment
1012 Modules / sensors
Key for function diagrams and installation diagrams
Special tools
REH rear linkage module – A058
Rear linkage and transmission module – A164
Wiring for connectors A and B
EGR module – A165
TALOS 210-220-230
Engine speed sensor
TALOS 210-220-230
TALOS 240
1015 Wiring harnesses
Key for function diagrams and installation diagrams
Special tools
Harness identification
Connectors
Harness 1 – Engine harness
TALOS 210 and 230 engines
TALOS 220 engine
TALOS 240 engine
Starting in cold weather
Harness 2 – Front lighting harness
Harness 3 – Internal EGR harness
Injection pump harness (Bosch pump) – TALOS 210-220-230
Harness 4 – Main harness
Main harness – Cab version
Main harness – Platform version
Harness 5 – Linkage harness
With mechanically controlled linkage
With electrohydraulically controlled linkage
Harness 6 – Cab harness
Cab harness
Air conditioning
Harness 8 – Transmission and electrohydraulic linkage harness – Options
PSS reverser and electrohydraulic range (TALOS 240)
1080 Electronic circuit diagram
Key for function diagrams and installation diagrams
Special tools
Differential lock
4-wheel drive transmission
Power take-off
Ignition
Stopping the engine – Cold starting
Starter / Alternator
Engine oil pressure switch
Tachometer / Thermometer
Fuel level
Clock / Terminal
Lighting
Indicators / Hazard warning lights
Transmission oil temperature sensor
Air conditioning / Indicators
Windscreen wiper / Windscreen washer / Audio / Cigarette lighter
Work lights / Overhead lights
12 Cab / Operator’s platform
1210 Cab
Separating the cab
Diagnosis by fault codes
Error codes
Introduction
Error code display
List of error codes
Position of components
Electric system
Location of components
A058 Rear linkage module (REH) – A164 Rear linkage and transmission module
A165 EGR module (TALOS 220)
A166 4-wheel drive and differential module
B117 Steering angle sensor
B144 Force sensor potentiometer
B334 Rear linkage position sensor potentiometer
B407 Working depth sensor potentiometer
Z219 Reverse gear switch
Flashing unit
Ignition relay
Main harness connectors
Electrohydraulically controlled linkage harness connectors
Electrohydraulically controlled linkage connectors
Sensors in the engine
TALOS 240 engine

00 1150 411 1.pdf:

TALOS 240-230-220-210
Table of contents
Introduction
General information
Using this repair manual
Scope of the repair manual
General repair instructions
Technical specifications
Cause of damage
Spare parts
Diesel engine
Alternator
Welding work
Drive belt/drive chains
Tapered ring assemblies
Self-locking bolts with microencapsulated glue
Threadlock
Lock collar bearing
Collet bearing
Threaded unions with cutting rings on the hydraulic hoses
Threaded unions with progressive rings on the hydraulic hoses
Threaded double flare unions on the hydraulic hoses
Flexible hydraulic pipes
Advice for economical repairs
Tightening torques
Tightening torques for NF E25-030-1 2007-12-01 standard metric threads
Technical specifications
Lubricants
CCN explanation
CCN (CLAAS Component Number)
Electric systems standard
Overview
Hydraulic system standard
Overview
CCN Index
General information
Important
Identification of warning and danger signs
General safety and accident prevention regulations
Leaving the machine
Adjusting and maintenance work
Danger of injury from hydraulic liquid
Air conditioner
Hydraulic accumulators
First aid measures
Battery isolating switch
Safety routines
Putting the machine out of operation
01 Engine
0102 Complete component
Introduction
Assistance operation
General notes
General notes on the electrical circuit
Earth and shielding
Conversion between the main units of measurement of the international system and the units derived from current usage
General points
Engine views – TALOS 240
Engine views – TALOS 230
Engine views – TALOS 220
Engine views – TALOS 210
General engine service
Special tool
General specifications
Assembly play
Tightening torques
TALOS 230-220-210
TALOS 240
Removing the engine
Removing the cab
Removing the fuel tank
Right-hand side of engine
Left-hand side of engine
Left-hand section
Rear section
Front section
Removing the engine peripherals
Removing the radiator
Removing the engine frame
Separating the engine
Engine peripherals – TALOS 230-220-210
Versions with or without EGR
Locating top dead centre on cylinder 1
Timing gear train housing
Refitting the rear end components
Refitting the flywheel
Refitting the front end components
Calibration
Piston protrusion measurement
Version without “EGR”
Version with “EGR”
Checks and inspections
Engine peripherals – TALOS 240
Removing/fitting the engine peripherals
Introduction
Special tools
Removing the engine peripherals
Fitting the engine peripherals
Adjusting the rocker clearance
Removing and refitting the injection Locating top dead centre
Checks and inspections
0115 Engine unit
Repairing the cylinder block
Checks and measurement Checking the supporting surface of the cylinder head on the cylinder block
Removing the connecting rods/pistons/crankshaft and camshaft
Crankshaft
Measuring the journals and crank pins
Table of values measured
Main crankshaft tolerances
Replacing the oil pump drive pinion
Fitting the crankshaft bearings
Measuring the journal play
Checking the crankshaft axial play
Connecting rod/piston assembly
Special tool
Main dimensions of the piston, pins and rings
Piston pin
Conditions required for correct coupling of the pin and piston
Piston rings
Fitting the connecting rod/piston assembly – Coupling the connecting rod/piston
TALOS 240
TALOS 230-220-210
Fitting the piston rings
Fitting the connecting rod/piston assemblies in the liners
Measuring the connecting rod axial play
Piston protrusion measurement
0120 Cylinder head / Valves / Idler gear
Special tools
Camshaft
Main dimensions of the camshaft bearings
Checking the cam lift and the alignment of the shaft cylinders
Main dimensions of the camshaft bearings and seat
Replacing the rings
Pushrods
Fitting the pushrods – Camshaft
Cylinder head
Special tools
Removing the valves
Checking the cylinder head sealing
Checking the cylinder head supporting surface
Main dimensions of the intake and exhaust valves
Decarbonising, checking and rectifying the valves
Checking the clearance between the valve stem and the valve guide – centring the valves
Valve guide
Replacing the valve guide
Valve seats
Main dimensions of the valve seats – in mm
Rectifying/replacing the valve seats
Valve springs
Fitting the cylinder head
0125 Injection – / Fuel system
Fuel supply – TALOS 210220230
General points
Schematic diagram
Hose diagram
Operating principle
Injection pump
Supply phase
Flow phase
End of flow phase
Stopping the engine
LDA device (adaptation of the flow according to the load)
Priming pump
Fuel filter
Injection system – TALOS 210-220-230
Special tools
Removing/refitting the injection pump
Preliminary operations
BOSCH VE 4/12 F pump
Refitting
Checking the static advance of the injection pump on the engine at top dead centre on cylinder 1
Prerequisites
Fuel supply – TALOS 240
General points
Hose diagram
Operating principle
Injection pump
Priming pump
Fuel filter
Injection system – TALOS 240
Special tools
Removing/fitting the injection pump
Preliminary operations
Locating top dead centre
0130 Lubricating oil system
Engine lubrication – TALOS 230-220-210
Oil pump
Oil filter
Oil vapour recycling
Removing the blow-by on the cylinder head cover
Refitting the blow-by
Oil pressure switch
Engine lubrication – TALOS 240
Oil vapour recycling
Oil pressure switch
Specifications
0135 Cooling system
Cooling system – TALOS 210220230
Description
Water pump
Thermostat
Coolant temperature sensor
Coolant temperature sensor for the cold advance system.
Heat exchanger
Cooling system – TALOS 240
Description
Coolant temperature sensor
Specifications
Coolant temperature sensor for the cold advance system.
Specifications
Solenoid on supply pump
0145 Air intake
Turbocharging – TALOS 210-220-230
Turbocharging – TALOS 240
Cold starting assistance – TALOS 240
Preheating resistor
Specifications
0165 Exhaust gas aftertreatment
External EGR – TALOS 210-220-230
Operation
Air temperature and pressure sensor
EGR solenoid valve
02 Gearbox / Clutch / Universal drive shaft
0202 Complete component
Technical specifications
Transmission – General information
Transmission with mechanical reverser – Cross-sectional view
Transmission with Power Shuttle System – Cross-sectional view
Tightening torques
Transmission inspection
Removing/refitting the transmission
Faults and solutions
Removing the clutch housing
Removing the central casing
Removing the linkage cover
0215 Mechanical clutch
Clutch inspection and repair
Special tools
Description
Clutch – Cross-sectional view
Faults and solutions
Disassembling/assembling the clutch
Assembly
Mechanical clutch
Clutch and brake fluid levels
Bleeding the clutch
0218 Clutch control
Clutch master cylinder and lever
Clutch release bearing and clutch fork
Clutch pedal
Adjusting the clutch pedal clearance (mechanical clutch)
Setting the clutch pedal pressure force
0220 Mechanical reverser
0222 Hydraulical reverser
PSS reverser – Operation
Removing the PSS module
Reverser clutch
Components
Removing
Removing the Power Shuttle System reverser clutch components
Slow/fast gear clutch
Components
Removing
0228 Reverser control
Mechanical reverser control
Mechanical reverser control – Cross-sectional view
Drive train
View of reverser synchro and associated parts
Removing the mechanical reverser synchro
Checking for wear on the reverser synchro
PSS hydraulic reverser control
Description
Drive train
0230 Mechanical gearbox
Gearbox – Cross-sectional view
Range box
Range box – Cross-sectional views
Creeper range (depending on equipment)
Creeper range assembly – Cross-sectional view
Transmission – Removing the central casing components
Transmission – Removing the axle casing components
0238 Gearbox control
Gear lever
Description
Gear lever – Cross-sectional view
Drive train
Gear range control
Operation
Cross-sectional view
Range selector lever – Cross-sectional view
Drive train
Creeper range control
Operation
Cross-sectional view
Drive train
0240 Rear axle housing
Repairing the axle tubes
Axle tube – Cross-sectional views
Removing the axle tube
0242 Differential
Rear differential locking system
Special tools
Rear differential lock – General view
Description
Removing the rear differential
Rear differential lock hydraulic device
Removing the drive pinion shaft
Refitting the drive pinion shaft
Setting the clearance between the teeth and the drag torque
0252 Electro-hydraulical front axle drive
4-wheel drive transmission
Drive train
Operation
4-wheel drive transmission components
03 Chassis
0325 Driven steering axle, front
Taesan Machinery front axle
View of the front axle
Description
Tightening torques
Removing/fitting the front axle
Separating the front axle
View of the complete coupling bar
Adjusting and fitting the coupling bars
Repairing the wheel reduction gear
Wheel reduction gear – Cross-sectional view
Description
Wheel hub components
Repairing the wheel hub
Setting the clearance between the teeth (between the crown wheel and the stub axle)
Repairing the pivot
Setting the clearance between the teeth (between the 17-tooth bevel pinion and the wheel shaft)
Front axle differential
Front axle and drive pinion differential – Cross-sectional view
Setting the position of the drive pinion shaft
Preloading the drive pinion bearing
Repairing the front axle differential
Setting the clearance between the teeth (between the drive pinion and the crown wheel)
0325 Driven steering axle, front
CARRARO front axle
View of the front axle
Description
Characteristics of the limited slip differential discs
Front axle
Wheel hubs and reducer
Exploded view
Special tool
Preliminary operations
Wheel pivots
Exploded view
Preparation for work
Special tool
Preliminary operations
Exploded view
Preliminary operations
Drive pinion sealing ring
Exploded view
Special tool
Wheel shafts
Exploded view
Preparation for work
Special tool
Preliminary operations
Differential – Removal and fitting operations
Exploded view
Preparation for work
Special tool
Preliminary operations
Adjustment
Checking the contact imprint of the differential teeth
Differential (LS) – Removal and fitting operation
Exploded view
Preliminary operations
Disassembly
Assembly
Differential (ML) – Removal and fitting operation
Exploded view
Preliminary operations
Disassembly
Assembly
Differential lock
Exploded view
Preliminary operations
Drive pinion
Exploded view
Preparation for work
Special tools
Preliminary operations
04 Brake
0405 Service brake
Service brakes – General information
Specifications
Faults and solutions
Service brakes
Removing the service brakes
Master cylinder
Bleeding the brake hydraulic circuit
Adjusting brake pedal clearance
0415 Parking brake
Handbrake
Handbrake components
Removing the handbrake
Removing the handbrake components
05 Steering
0505 Steering
Steering system – General information
Steering system components
Description
Tightening torques
Steering operating diagrams
Neutral position
Turned to the right/left
Turned to the right (1)
Turned to the left (2)
Faults and solutions
Steering unit
Removing/fitting the steering unit
Removing/refitting the steering gearbox
Steering actuator – Taesan Machinery front axle
Cross-section
Removing the steering actuator
Refitting the steering actuator
Steering actuator – Carraro front axle
Exploded view of the steering actuator
Preliminary operations before operating on the steering actuator
Removing the steering actuator
Repairing the steering actuator
Fitting the steering actuator
Adjusting the fixed front axle alignment
Preparation for work
Adjusting the fixed front axle alignment
06 Lift device
0605 Rear power lift
Description of the mechanically-controlled hydraulic linkage
Operating principle
Components
Description
Oil flow
Neutral position
Raising position
Lowering position
Linkage control valve
Linkage control valve hydraulic diagram
Specifications
Connections
Linkage controls
Raising the rear linkage
Lowering the rear linkage
Force control
Automatic lifting
Removing/fitting the mechanically-controlled hydraulic linkage cover
Components
Mechanically-controlled hydraulic linkage control valve
Description of the electronically-controlled hydraulic linkage
CAN bus diagram
Rear hydraulic linkage electronic control system sensors
Electronic control for rear hydraulic linkage (multifunction armrest)
User controls
Working depth control
Linkage cover – Components
Description
Hydraulic diagram
Throughput adjustment
Linkage control valve
Oil flow
Neutral position
Raising position
Lowering position
Proportional solenoid valves
Throughput adjustment
Removing/refitting the electronically-controlled hydraulic linkage cover
Electro-hydraulic linkage control valve
Rear hydraulic linkage – Faults and solutions
Calibrating the lower linkage stop
Adjusting the upper connecting rod
Calibrating the position control lever lower limit
Setting the power take-off automatic disengagement point
08 Drives
0802 Rear PTO
Rear power take-off system
Power take-off proportional to ground speed
User controls
Removing the power take-off proportional to ground speed
Rear power take-off system – View of components
Rear power take-off speed selector lever
Power take-off speed selection – Cross-sectional view