File List:
00 0293 117 0.pdf
00 0293 117 0.pdf:
Foreword
Foreword
Foreword
Bibliography
Security
Maintenance
Maintenance intervals
California Recommendation 65 Warning Statement
Certified engine maintenance service
Machine performance
Security Chapter
Security Chapter
Safety instructions and stickers
stop the engine
Security support
Remove the cutting mechanism
Liquid inlet
drive shaft
Missing protective devices
General danger instructions
Pressurized air and water
Liquid inlet
Prevention against bruises and cuts
Safety supports
Prevention against burns
Prevention against fires and explosions
Pipes, tubes and hoses
Before start-up
Functioning
Road traffic
Chapter Product information
Model views and specifications
Model views and specifications
Trap key
Calculation factors
Cutting mechanism
Safety device
Weights and Measures
Identification information
Plate and film positions
Chapter Before start-up
Coupling part for machines with CLAAS AUTO-CONTOUR
Assemble the coupling piece
Chapter Management
harvest dividers
Adjust the tips of the crop divider
Basic settings of crop dividers
Replace the tips of the crop divider
Mount the supplement on the long tips of the crop divider
cutting saw
Remove the blade
Assemble the blade
Standard blade system
Adjust the standard blade system
SG3/S system and SG3 blade system
Adjust the SG3/S system and SG3 blade system
Replacement blade
Level the base of the blade
Cutting skids
Pinwheel
Reel height adjustment
Adjusting the minimum reel height
reel tines
Reel adjustment (forward and backward)
Reel drive
Horizontal adjustment of the reel
Feed auger
Feed auger height adjustment
Auger Feed Finger Adjustment
Adjusting the scraper bars
Safety device
Adjust the wiper profiles on the cutting mechanism
Change the inclination of the saw
Transformation from soy to cereal
Dismantle the soybean probes
Assemble the probes
Transform sensors and adjust them
Adjust the sensor shift lever relative to the end stops
Fix the saw
Transformation from cereal to soybeans
Transform sensors and adjust them
Adjust the sensor shift lever relative to the end stops
Assemble the soybean probes
Unlock the outer skid of the transverse swing arm
Remove the saw fixing screws
Maintenance Chapter
General instructions regarding tightening torques
Standard tightening torques for helical thread clamps
Standard tightening torques for metric unions
Tightening torques for standard threads in Nm, for hexagonal screws, cylindrical screws and hexagonal nuts
Tightening torques for fine threads in Nm, for hexagonal screws, cylindrical screws and hexagonal nuts
Maintenance and lubricant table
Maintenance table
Lubricant table
Hydraulic system
Bleeding the reel cylinders – horizontal adjustment of the reel
Blade drive
Check oil level / change oil
Adjust gearbox support
Drive belts/drive chains
Remove the blade drive belt (40)
Install the blade drive belt (40)
Tighten the feed auger drive chain (41)
Tension the reel drive chain (47)
Reel drive single contact
General notes
Remove chaff and dirt from the elastic plates
Adjust the pull spring to unload the skids
Machine – cleaning / conservation during winter
Greasing plans
Lubricants and indications
Chapter Technical Service Information
Troubleshooting
Problems in the cutting mechanism
The blade stops
Harvest material is not collected
Foreign material on the tip of the crop divider
The reel stops
The reel does not turn
Cutting mechanism without side compensation is not straight
The material flow of the cutting mechanism is not homogeneous
The endless stops
The material is wound on the ends of the reel
The material is wound in the center of the reel
The fingers of the reel touch the saw
The reel is not straight
Alphabetical index
Alphabetical index
Claas Operator Manual PDF
Claas Operator Manual PDF
Claas QUANTUM 6800-4500 GT P (615) Loader Wagons Operator Manual DE
Claas Operator Manual PDF
![](https://automanual.net/wp-content/uploads/2024/04/claas-f900-f750-f530-f525-f30-f25-f20-438-combines-operator-manual-es-1.jpg)