Claas Disco 210 Rc (624) Mower Operator Manual ES

File List:

00 0295 066 2.pdf

00 0295 066 2.pdf:

DISC 210 RC
1 Regarding this instruction manual
1.1 Information regarding the instruction manual
1.1.1 General instructions
1.1.2 Manual handling
Direction signs
1.1.3 Validity of the manual
1.1.4 Symbols and indications
1.1.5 Technical instructions
2 Security
2.1 Safety instructions
2.1.1 To take special account
2.1.2 Qualification of piloting and maintenance personnel
2.1.3 Proper machine application
2.1.4 Logically foreseeable inappropriate application
2.1.5 Protection and safety standards at work
2.1.6 First aid measures
2.1.7 Risk of injury from hydraulic fluids
2.2 Safety instructions on the machine
2.2.1 Warning symbols
2.2.2 Position of warning symbols
3 Machine Description
3.1 Summary and operation
3.1.1 Summary DISCO 210 RC
3.1.2 DISCO 210 RC operating mode
3.2 Optional machine equipment
3.2.1 High cut skates
3.2.2 Screw-on wear pads
3.2.3 Insertable fork for cardan shaft 8 components
3.2.4 Protection bar
3.2.5 Hydraulic connection parts 1 components
3.2.6 Support for warning signs
3.3 Identification plates and vehicle identification number
3.3.1 Nameplate position
3.3.2 Mower identification plate explanation
3.3.3 Spare parts and technical queries
4 Control and display instruments
4.1 Mounting frame
4.1.1 Stopcock
4.2 Mower unit
4.2.1 Traction cables
4.3 Conditioner
4.3.1 Crutch nut
5 Technical data
5.1 DISC 210 RC – Type 624
5.1.1 Measurements
5.1.2 Weights
5.1.3 Requirements for the tractor
5.1.4 Model
5.1.5 Acoustic intensity level
5.1.6 Inputs and filling quantities
6 Preparation of the machine
6.1 Prepare the tractor
6.1.1 Axle loads, minimum counterbalance, total weight
6.1.2 Calculate the minimum front counterbalance
6.1.3 Calculate the minimum rear counterweight
6.1.4 Calculate the actual front axle load
6.1.5 Calculate the actual total weight
6.1.6 Calculate the real rear axle load.
6.1.7 Calculation table
6.2 Adapt the machine
6.2.1 Adapt the lower bar bolt
6.2.2 Cardan shaft – check the length
6.2.3 Cardan shaft – adapt the length
6.2.4 Mount the cardan shaft to the machine
6.3 Hooking up the machine
6.3.1 Attach the support to three points
6.3.2 Assemble the cardan shaft
6.3.3 Connect the hydraulic pipes
6.3.4 Place the support leg upwards
6.3.5 Place the pull ropes
6.4 Unhook the machine
6.4.1 Prepare for disassembly
6.4.2 Remove the support leg
6.4.3 Remove the pull ropes
6.4.4 Uncouple the hydraulic pipes
6.4.5 Dismantle the cardan shaft
QS Closure
6.4.6 Unhook the three-point support
6.5 Machine loading
6.5.1 Load/unload the machine
7 Management
7.1 General security measures
7.1.1 Take into account before handling
7.2 Driving on the road
7.2.1 Road traffic
7.2.2 Machine marking for road traffic
7.3 Settings for use at work
7.3.1 Adjust the support to three points
7.3.2 Adjust mower discharge
7.3.3 Adjust cutting height
7.3.4 Adjust swath width
7.3.5 Adjust the roller conditioner
7.3.6 Mowing without roller conditioner
7.3.7 Fixing the crash protection
7.3.8 Retension crash protection
7.4 Use at work
7.4.1 Take into account during field trips
7.4.2 Place in transport position
7.4.3 Turn to working position
7.4.4 Using the machine
7.4.5 Mowing technique
7.4.6 Position at the ends of the plot
7.4.7 Instructions for mowing
7.4.8 Difficult harvest conditions
7.4.9 Recommendation regarding environmental protection
8 Incident and solution
8.1 causes and solution
8.1.1 General warning instructions
8.1.2 General fault and solution
9 Maintenance
9.1 Maintenance instructions
9.1.1 General warning instructions
9.1.2 Electrical installation
9.1.3 Protection devices
9.1.4 Spare parts
9.1.5 Imbalance
9.1.6 Pressurized air and water
9.1.7 Prevention against burns
9.1.8 Oil
9.1.9 Prevention against fires and explosions
9.1.10 Pipes, tubes and hoses
9.2 Summary of maintenance intervals
9.2.1 Management of maintenance intervals
9.2.2 before starting the harvest
9.2.3 After the first 5 hours of service
9.2.4 After the first 10 hours of service
9.2.5 After the first 50 hours of service
9.2.6 Every 20 hours of service
9.2.7 Every 100 hours of service
9.2.8 Every 200 hours of service
9.2.9 Every 250 hours of service
9.2.10 Every 500 hours of service or annually
9.2.11 if necessary
9.2.12 After harvest
9.3 General maintenance work
9.3.1 Clean the machine
9.3.2 Maintain the machine
9.3.3 Fixing material
9.4 Gear maintenance work
9.4.1 Check the main gear oil level
9.4.2 Change main gear oil
9.4.3 Check the bevel gear oil level
9.4.4 Change bevel gear oil
9.5 Cardan shaft maintenance work
9.5.1 Maintain the cardan shafts
9.5.2 Roller conditioning cardan shaft
9.6 Hydraulic installation maintenance work
9.6.1 Hydraulic installation
9.6.2 Hydraulic hoses
9.6.3 Hydraulic cylinders
9.7 Maintenance work on the mowing device
9.7.1 Check the oil level in the cutter bar
9.7.2 Change the cutter bar oil
9.7.3 Change the blades
Change bolted blades
9.7.4 Check the mower blade support
9.7.5 Maintenance of mower discs
Clean the drain hole
9.7.6 Change the mower discs
9.7.7 Assembling the bevel pinion units
9.7.8 Adjust the protection device
Protective canvas support, front
9.8 Roller conditioning maintenance work
9.8.1 Tension the drive belts
9.8.2 Adjust the roller conditioner
Adjust the draft spring
Adjust synchronized gear
Adjust the distance of the rollers
9.9 Maintenance work mounting chassis
9.9.1 Adjust cutter bar discharge
9.10 Greasing scheme
9.10.1 Greasing points – 20 h
9.10.2 Grease points – 100 h
9.10.3 Grease points – 250 h
10 Decommissioning and waste disposal
10.1 General data
10.1.1 End of operational life and waste disposal
11 EU declaration of conformity
11.1 DISC 210 RC – Type 624
11.1.1 EC declaration of conformity
12 Technical dictionary and abbreviations
12.1 Terms and explanations
12.1.1 Technical vocabulary
12.1.2 Abbreviations