File List:
00 0291 105 4.pdf
00 0291 105 4.pdf:
LINER 4000
Introduction
Safety instructions
Safety and danger instructions
CCN Explanation
CCN (CLAAS Component Number)
General indications
Electrical regulations
Hydraulic regulations
CCN (CLAAS Component Number)
04 Brake
0410 Trailed machine service brake
Hydraulic service brake
single axis
Pneumatic service brake
single axis
Trailer brake valve, two-pipe brake
Function Description
Check and adjustment
08 Drives
0808 Main drive
Main drive
Table of measured values
Function Description
09 Hydraulic
0900 General instructions for the hydraulic installation
oil feed
Function Description
0920 Valves
LINER 4000 valve block
0980 Hydraulic connection diagram
LINER 4000 hydraulic connection diagram
10 Install. electrical/electronic
1012 Modules / sensors
CLAAS CONTROL UNIT module (A020)
Pin occupation
1080 Electronic connection diagram
LINER 4000 electrical connection diagrams
SCM 01 – Power supply / CAN-Bus
Denominations
SCM 02a – ISO-Bus connection
Denominations
SCM 02b – Control unit – COMMUNICATOR
Denominations
SCM 03 – Chassis
Denominations
SCM 04 – Front rotors
Denominations
SCM 05 – Rear rotors
Denominations
SCM 06a – Standard advance lighting
Denominations
SCM 06b – Advance lighting with contour lighting
Denominations
SCM 06c – Standard forward lighting with work lighting connection
Denominations
SCM 06d – Advance lighting with contour lighting and connection of work lighting
Denominations
SCM 07 – Lighting for work
Denominations
1081 Plug summary
Socket database (chp CLAAS)
Example of key number representation (CHP)
Key number (CHP)
Plug Representation (CHP)
1085 Networks
Table of measured values
Function Description
20 Reception of the harvest
2025 Pick holder / elastic picks
Raking height
Table of measured values
Function Description
60 Deposit the material / deposit the straw
6030 Harvest unloading / row placement / row former
Working width
Denominations
Table of measured values
Function Description
Row width
Table of measured values
Function Description
92 Diagnosis
9230 ISO Error Codes
FMI fault code (Failure Mode Indicator)
General indications
FMI 00 (signal too large)
FMI 01 (signal too small)
IMF 02 (implausible signal)
FMI 03 (voltage too high)
FMI 04 (voltage too low)
FMI 05 (current too low)
FMI 06 (current too high)
FMI 07 (mechanical failure)
FMI 08 (frequency signal defective)
IMF 09 (communication failure)
FMI 10 (signal change too fast)
IMF 11 (multiple failure)
FMI 12 (defective ECU)
FMI 13 (signal outside calibration range)
IMF 16 (non-existent parameter)
FMI 17 (ECU not responding)
FMI 18 (power supply failure)
FMI 19 (software requirements not met)
IMF 95 (no signal change)
FMI 96 (CAN-Bus system defective)
IMF 97 (implausible state)
IMF 98 (warning)
IMF 99 (Info)
LINER 4000 error codes (type G05)
99 total machine
9925 Transport position / working position
Transport position / working position
Table of measured values
Function Description
9997 Check / measure / adjust
Chassis position sensor (B284)
Adjustment
Front rotor position sensors (B285, B286)
Adjustment
Rear rotor position sensors (B287, B288)
Adjustment
Locking control sensor (B289)
Adjustment
Location of components
Hydraulic installation
1000 Oil tank / oil filter / oil radiator
3000 Hydraulic Cylinders
6000 Valves – mechanically actuated
7000 Valves – hydraulically actuated
8000 Couplings/connections
Electrical installation
To Terminal/modules
B Sensors
K Relays
R Potentiometer/ resistors
X Pluggable connections
and electromagnetic coil
Claas Technical System PDF
Claas Technical System PDF
Claas RANGER 928, 925, 920 und PLUS (510) Telehandlers Technical System DE
Claas Technical System PDF
Claas QUANTUM 3800 K 3500 P-K-S (613) Loader Wagons Technical System DE
Claas Technical System PDF
Claas QUANTUM 6800-4500 GT P (615) Loader Wagons Technical System DE
Claas Technical System PDF
Claas QUANTUM 5500 S S16 S18 4500 S (614) Loader Wagons Technical System DE
![](https://automanual.net/wp-content/uploads/2024/04/claas-liner-4000-g05-swathers-technical-system-es-1.jpg)