komatsu ae50 am50 series electric lift truck shop manual bba12c1 04 1

komatsu ae50 am50 series electric lift truck shop manual bba12c1 04 2 1

komatsu ae50 am50 series electric lift truck shop manual bba12c1 04 3 1

komatsu ae50 am50 series electric lift truck shop manual bba12c1 04 4

komatsu ae50 am50 series electric lift truck shop manual bba12c1 04 5

Komatsu AE50, AM50 Series Electric Lift Truck Shop Manual BBA12C1-04

$40.00

Type Of Manual: Shop Manual
Manual ID: BBA12C1-04
Format: PDF
Size: 20.7MB
Number of Pages: 452

Category: Komatsu Shop Manual PDF

Model List:
- AE50 Series Electric Lift Truck
- AM50 Series Electric Lift Truck

1. COVER
2. SECTION INDEX
3. GENERAL AND SPECIFICATIONS
3.1. OUTSIDE VIEW
3.2. SPECIFICATIONS
3.3. PERIODIC REPLACEMENT OF CONSUMABLE PARTS
3.4. SAFETY ITEMS FOR MAINTENANCE
3.5. STANDARD TIGHTENING TORQUE FOR BOLTS
3.6. STANDARD TIGHTENING TORQUE FOR PIPE JOINTS
3.7. HOW TO USE LOCTITE
4. TESTING AND ADJUSTING
4.1. SERVICE DATA
4.2. METHOD OF RELEASING THE PRESSURE IN THE HYDRAULIC PIPING
4.3. LIFT INTERRUPT FUNCTION
4.4. METER PANEL
4.5. OPERATION OF METER PANEL
4.6. BATTERY
4.7. FUSE
4.8. TRANSFER CASE
4.9. ADJUSTMENT OF WET TYPE BRAKE AND PARKING BRAKE
4.10. WET TYPE BRAKE
4.11. HYDRAULIC OIL TANK
4.12. MAST
4.13. FINGER BAR
4.14. NATURALLY DESCENDING AMOUNT OF HYDRAULIC OIL CYLINDER,MEASUREMENT OF NATURALLY FORWARD TILTING AMOUNT
4.15. AIR BLEEDING
4.16. LIST OF LUBRICANT AND GREASE
5. REMOVAL AND INSTALLATION
5.1. UNIT LOCATION DIAGRAM
5.2. UNIT MASS
5.3. DRAWING OF DISASSEMBLY/ASSEMBLY
5.4. HYDRAULIC PUMP AND PUMP MOTOR
6. DISASSEMBLY AND ASSEMBLY
6.1. DRIVE AXLE
6.2. TRANSFER
6.3. BRAKE WHEEL CYLINDER
6.4. BRAKE MASTER CYLINDER
6.5. STEERING GEAR BOX
6.6. ORBITROL
6.7. POWER STEERING CYLINDER
7. MAINTENANCE STANDARD
7.1. DRIVE AXLE
7.2. BRAKE MASTER CYLINDER
7.3. MAST, FINGER BAR, FORK
7.4. DRIVE MOTOR
7.5. PUMP MOTOR
8. STRUCTURE AND FUNCTION
8.1. BRAKE
8.2. HYDRAULIC CIRCUIT DIAGRAM
8.3. CONTROL VALVE
9. TROUBLESHOOTING
9.1. DIAGNOSIS TOOL
9.2. CONFIGURATION PARTS, SENSOR, UNIT LOCATION DRAWING
9.3. LOCATION DRAWING
9.4. HARNESS LIST
9.5. LOCATION OF CPU BOARD CONNECTOR
9.6. OVERVIEW OF ABNORMAL CODE
9.7. PREPARATION FOR VOLTAGE CHECK AND CURRENT CHECK
9.8. INPUT / OUTPUT SIGNAL OF CONTROLLER
9.9. ABNORMAL CODE LIST
9.10. DIAGNOSTIC PROCEDURE BY ABNORMAL CODE
9.11. DIAGNOSTIC PROCEDURE BY METER DISPLAY TROUBLE CODE
9.12. TROUBLE WITHOUT ABNORMAL DISPLAY
9.13. PROPORTIONAL SOLENOID VALVE CONTROLLER
9.14. ADJUSTMENT PROCEDURE OF TILT AUTOMATIC HORIZONTAL (OPTION)
9.15. METER PANEL
10. YEARLY INSPECTION CRITERIA
10.1. Motor
10.2. Control Equipment
10.3. Battery
10.4. Power Transfer Equipment
10.5. Traveling equipment
10.6. Steering equipment
10.7. Braking equipment
10.8. Cargo handling equipment
10.9. Hydraulic equipment
10.10. Body, Safety Equipment, etc
10.11. Total test
11. CONVERSION TABLE
11.1. Millimeters to Inches
11.2. Inches to Millimeters
11.3. Cubic meters to Cubic yards
11.4. Cubic yards to Cubic meters
11.5. Liter to U.S. Gallon
11.6. Gallon to Liter
11.7. Liter to U.K. Gallon
11.8. Gallon to Liter
11.9. Kilogram to Pound
11.10. Pound to Kilogram
11.11. kg/cm2 to Ib/in2
11.12. kgm to ft. Ib
11.13. Temperature
12. APPENDIX
12.1. A9799310 (INPUT CAP PRESSFITTING JIG)
12.2. A9799320 (INPUT OIL SEAL PRESSFITTING JIG)
12.3. A9799330 (INPUT HUB BEARING PRESSFITTING JIG)
12.4. A9799710 (INPUT GEAR/BEARING PRESSFITTING JIG)
12.5. A9799720 (MULTIPLE DISC ALIGNMENT JIG)
12.6. A9799730 (MULTIPLE HOLDER CLEARANCE ALIGNING JIG)
12.7. A9799740 (3WHEEL REAR AXLE PRESSFITTING JIG)
12.8. A9799760 (3WHEEL REAR AXLE SENSOR ALIGNMENT JIG)
12.9. SERVICE TOOL CONFIGURATION
12.10. ELECTRIC WIRING DIAGRAM

Rate this product