bomag bw 226 dh 4 single drum roller operating and maintenance instructions 00804041 1

bomag bw 226 dh 4 single drum roller operating and maintenance instructions 00804041 2

bomag bw 226 dh 4 single drum roller operating and maintenance instructions 00804041 3

bomag bw 226 dh 4 single drum roller operating and maintenance instructions 00804041 4

bomag bw 226 dh 4 single drum roller operating and maintenance instructions 00804041 5

Bomag BW 226 DH-4 Single Drum Roller Operating and Maintenance Instructions 00804041

$20.00

Type Of Manual: Operating and Maintenance Instructions
Manual ID: 00804041
Format: PDF
Size: 8.8MB
Number of Pages: 192
Serial Number:
861582361001 and up

Category: Bomag Operator Manual PDF

Model List:
- BW 226 DH-4 Single Drum Roller

1. Table of contents
2. Introduction
2.1. Foreword
2.2. Machine type plate and engine type plate
3. Technical data
4. Safety regulations
5. Display and control elements
5.1. General notes
5.2. Description of indicators and control elements
5.3. Display and control elements BTM
5.4. Description of indicating and control elements BTM
5.5. Line diagram (EVIB)only BTM prof
5.6. Description of line diagram (EVIB)only BTM prof
6. Operation
6.1. General
6.2. Tests before taking into operation
6.3. Electronic immobilizerOptional equipment
6.4. Adjusting the drivers seat
6.5. Starting the engine
6.6. Driving the machine
6.7. Stopping the machine, operating the parking brake
6.8. Shutting down the engine
6.9. Switching the vibration on and off
6.10. What to do in events of emergency
6.11. Adjusting the steering wheel
6.12. Operating the heating / air conditioning system
6.13. Operating the hood
6.14. LCDisplay changing display fields
6.15. LCDisplay changing settings
6.16. BTM 05 settings before startupOptional equipment
6.17. Measuring pass with BTMOptional equipment
6.18. Finishing compaction of a track
6.19. Printing measuring data after completing compactiononly BTM prof
6.20. Changing the paper roll in the measuring value printeronly BTM prof
6.21. Changing the printer ribbon in the measuring value printeronly BTM prof
6.22. Towing when an engine failure has occurred
6.23. Loading/transport
7. Maintenance
7.1. General notes on maintenance
7.2. Fuels and lubricants
7.2.1. Engine oil
7.2.1.1. Oil quality
7.2.1.2. Oil viscosity
7.2.1.3. Oil change intervals
7.2.2. Fuel
7.2.2.1. Fuel quality
7.2.2.2. Winter fuel
7.2.2.3. Storage
7.2.3. Coolant
7.2.3.1. General
7.2.3.2. Water quality
7.2.3.3. Cooling system protection agent
7.2.4. Hydraulic oil
7.2.4.1. Mineral oil based hydraulic oil
7.2.4.2. Biodegradable hydraulic oil
7.2.5. Gear oil SAE 80W140
7.2.6. Gear oil SAE 75W90
7.3. List of fuels and lubricants
7.4. Runningin instructions
7.4.1. General
7.4.2. After 250 operating hours
7.4.3. After 500 operating hours
7.4.4. After 1000 operating hours
7.5. Maintenance table
7.6. Every 10 operating hours
7.6.1. Check the engine oil level
7.6.2. Checking the fuel level
7.6.3. Check the coolant level
7.6.4. Check the hydraulic oil level
7.7. Every 250 operating hours
7.7.1. Check the tire pressure
7.7.2. Clean the cooling fins on engine and hydraulic oil cooler
7.7.3. Check the oil level in the drive axle
7.7.4. Check the oil level in the wheel hubs
7.7.5. Check the oil level in the axle reduction gear
7.7.6. Check the oil level in the drum reduction gear
7.7.7. Check the oil level in the vibration bearings
7.7.8. Check the parking brake
7.7.9. Check, replace the refrigerant compressor Vbeltoptional equipment
7.8. Every 500 operating hours
7.8.1. Change engine oil and oil filter cartridge
7.8.2. Checking, cleaning the water separator
7.8.3. Draining the sludge from the fuel tank
7.8.4. Battery service
7.8.5. Servicing the air conditioning systemoptional equipment
7.8.6. Cleaning the circulation air filter for the heatingOptional equipment
7.8.7. Changing the bypass filterOptional equipment
7.9. Every 1000 operating hours
7.9.1. Checking / replacing the ribbed Vbelt
7.9.2. Replace the fuel filter cartridge
7.9.3. Change the fuel prefilter cartridge
7.9.4. Check the engine mounts
7.9.5. Checking the engine pillow blocks
7.9.6. Changing the oil in the vibration bearings
7.9.7. Changing the oil in the drum reduction gear
7.9.8. Changing the oil in the drive axle
7.9.9. Changing the oil in the wheel hubs
7.9.10. Changing the oil in the axle reduction gear
7.9.11. Retightening the fastening of the axle on the frame
7.9.12. Tighten the wheel nuts
7.9.13. Check the ROPS
7.9.14. Check the travel control
7.10. Every 2000 operating hours
7.10.1. Adjust the valve clearance
7.10.2. Changing hydraulic oil and breather filter
7.10.3. Changing the hydraulic oil filter
7.10.4. Changing the coolant
7.11. Every 3000 operating hours
7.11.1. Replacing ribbed Vbelt and idler pulley
7.12. Every 6000 operating hours
7.12.1. Replace the injection valves
7.12.2. Replacing the crank case ventilation valve
7.13. As required
7.13.1. Air filter maintenance
7.13.2. Retightening the padfoot shell
7.13.3. Adjust the scrapers
7.13.4. Clean the machine
7.13.5. Change the tires
7.13.6. Change the fresh air filter in the cabin
7.13.7. Fill the provision tank for the windscreen washer systemOptional equipment
7.13.8. Tightening torques
7.13.9. Engine conservation
8. Trouble shooting
8.1. Preliminary remarks
8.2. Starting the engine with jump leads
8.3. Reading out faults BVC/BTM05
8.4. Fuse assignment
8.4.1. Notes on safety
8.4.2. Central electrics
8.4.3. Main fuses
8.4.4. Fuse, cabin
8.5. Engine problems
9. Cabin assembly before initial commissioning
9.1. Preparations
9.2. Cabin assembly
9.3. Final function tests and checks
10. Disposal
10.1. Final shutdown of machine

Rate this product