Support
Email
admin@automanual.net
Follow us
Clark Perkins 700 Series Workshop Manual
Clark Perkins 700 Series Workshop Manual - Image 2
Clark Perkins 700 Series Workshop Manual - Image 3
Clark Perkins 700 Series Workshop Manual - Image 4
Clark Perkins 700 Series Workshop Manual - Image 5
clark perkins 700 series workshop manual 2
clark perkins 700 series workshop manual 3
clark perkins 700 series workshop manual 4
clark perkins 700 series workshop manual 5

Clark Perkins 700 Series Workshop Manual

$40.00

  • Type Of Manual: Workshop Manual
  • Format: PDF
  • Size: 16.0MB
  • Number of Pages: 200
Category:
  • Model List:

    • Perkins 700 Series
  • 1. USERS HANDBOOK
  • 1.1. General information
  • 1.1.1. Title page
  • 1.1.2. Introduction
  • 1.1.3. Contents
  • 1.1.4. How to care for your engine
  • 1.1.5. Safety precautions
  • 1.1.6. Engine identification
  • 1.1.7. Perkins companies
  • 1.2. Engine Views
  • 1.2.1. Introduction
  • 1.2.2. Location of engine parts
  • 1.3. Operation Instructions
  • 1.3.1. How to start a cold engine in cold conditions
  • 1.3.2. How to start a cold engine in temperate conditions
  • 1.3.3. How to stop the engine
  • 1.3.4. Adjustment of engine speed range
  • 1.3.5. Runningin
  • 1.3.6. How to start the engine
  • 1.3.7. Engine operation at idle speed
  • 1.3.8. Altitude
  • 1.3.9. Angle of tilt
  • 1.4. Preventive Maintenance
  • 1.4.1. Preventive maintenance periods
  • 1.4.2. Schedules
  • 1.4.3. How to drain the cooling system
  • 1.4.4. How to check the specific gravity of the coolant
  • 1.4.5. How to check the drive belt
  • 1.4.6. How to adjust the belt tension
  • 1.4.7. How to renew the element / canister of the fuel filter
  • 1.4.8. Atomiser fault
  • 1.4.9. How to renew an atomiser UA and UC engines
  • 1.4.10. How to renew an atomiser UB engines
  • 1.4.11. How to eliminate air from the fuel system
  • 1.4.12. How to renew the lubricating oil
  • 1.4.13. How to renew the canister of the lubricating oil filter
  • 1.4.14. How to renew the engine breather assembly UA and UB engines
  • 1.4.15. Air filter
  • 1.4.16. How to set the valve tip clearances
  • 1.5. Engine Fluids
  • 1.5.1. Fuel specification
  • 1.5.2. Lubricating oil specification
  • 1.5.3. Coolant specification
  • 1.6. Fault Diagnosis
  • 1.6.1. Problems and possible causes
  • 1.6.2. List of possible causes
  • 1.7. Engine Preservation
  • 1.7.1. Introduction
  • 1.7.2. Procedure
  • 1.8. Parts and Service
  • 1.8.1. Introduction
  • 1.8.2. Service literature
  • 1.8.3. Training
  • 1.8.4. POWERPART recommended consumable products
  • 1.9. General Data
  • 2. WORKSHOP MANUAL
  • 2.1. How to use this manual
  • 2.2. Foreword
  • 2.3. Contents
  • 2.4. Section 10 General Information
  • 2.4.1. Consumable products.
  • 2.4.2. Engine identification location
  • 2.4.3. Engine views naturally aspirated engine
  • 2.4.4. Engine views turbocharged engine
  • 2.4.5. Compression test data
  • 2.5. Section 11 Specifcations
  • 2.5.1. Specifications
  • 2.5.2. Recommended torque tensions
  • 2.5.3. Data and dimensions
  • 2.6. Section 12 Cylinder Head Assembly
  • 2.6.1. Rocker cover to remove and to fit
  • 2.6.2. Rocker assembly (latest engine) to remove and to fit
  • 2.6.3. Rocker assembly (earlier engines) to remove and to fit
  • 2.6.4. Rocker shaft (latest engines) to dismantle, to inspect and to assemble
  • 2.6.5. Rocker shaft (earlier engines) to dismantle, to inspect and to assemble
  • 2.6.6. Valve tip clearance to check
  • 2.6.7. Valve springs (with cylinder head fitted) to remove and to fit
  • 2.6.8. Exhaust / Induction manifolds and gaskets to remove and to fit
  • 2.6.9. Cylinder head setscrews to remove and to fit
  • 2.6.10. Cylinder head gasket to remove and to fit
  • 2.6.11. Valve and valve springs to remove and to fit
  • 2.6.12. Valve stem to inspect
  • 2.6.13. Valve depth to check
  • 2.6.14. Valve guides to check
  • 2.6.15. Valve guides to remove and to fit
  • 2.6.16. Valve seats to correct
  • 2.6.17. Valve seat insert to fit
  • 2.6.18. Cylinder head to check the distortion of the lower face
  • 2.7. Section 13 Connecting Rod Assembly
  • 2.7.1. Big end bearing and cap to remove and to fit
  • 2.7.2. Piston and connecting rod to dismantle and assemble
  • 2.7.3. Piston and piston ring inspection
  • 2.7.4. Piston and piston ring to inspect
  • 2.7.5. Piston and connecting rod to fit
  • 2.7.6. Connecting rod to check for bend and to inspect
  • 2.7.7. Connecting rod to check the length and to inspect
  • 2.7.8. Small end bush to remove and to fit
  • 2.7.9. To check the piston height above the cylinder block
  • 2.7.10. Piston cooling jets (UC engines) to remove and to fit and to align
  • 2.8. Section 14 Crankshaft Assembly
  • 2.8.1. Crankshaft pulley to remove and to fit
  • 2.8.2. Crankshaft pulley to fit a wear sleeve
  • 2.8.3. Rear oil seal to remove
  • 2.8.4. Rear oil seal to fit
  • 2.8.5. Thrust washers and crankshaft endfloat to inspect
  • 2.8.6. Thrust washers to remove and to fit
  • 2.8.7. Main bearing caps (with crankshaft in position) to remove and to fit
  • 2.8.8. Main bearings to inspect
  • 2.8.9. Main bearing caps (front and rear) to remove
  • 2.8.10. Main bearing caps (front and rear) to fit
  • 2.8.11. Crankshaft to remove
  • 2.8.12. Crankshaft to fit
  • 2.8.13. Crankshaft to inspect and to overhaul
  • 2.8.14. Wearsleeve to fit
  • 2.9. Section 15 Timing Case and Drive Assembly
  • 2.9.1. Tamper proof screws
  • 2.9.2. Timing case to remove and to fit
  • 2.9.3. Timing case to fit
  • 2.9.4. Timing case to renew
  • 2.9.5. Front oil seal to remove and to fit
  • 2.9.6. Idler gear to remove
  • 2.9.7. Idler gear bushes to remove and to fit
  • 2.9.8. Idler gear hub to remove and to fit
  • 2.9.9. Camshaft assembly for the fuel injection pump to remove and to fit
  • 2.9.10. Camshaft assembly and tappets for the valves to remove and to fit
  • 2.9.11. Camshaft assembly for the valves to remove and to fit
  • 2.9.12. Crankshaft gear to remove and to fit
  • 2.9.13. Backplate to remove and to fit
  • 2.10. Section 16 Cylinder Block Assembly
  • 2.10.1. Cylinder block bores to inspect
  • 2.10.2. Camshaft bush to renew
  • 2.11. Section 17 Engine Timing
  • 2.11.1. To set accurately number 1 piston to TDC on the compression stroke
  • 2.11.2. To set accurately number 1 piston to TDC on the compression stroke
  • 2.11.3. To check valve timing
  • 2.11.4. Fuel injection pump timing
  • 2.12. Section 18 Turbo charger
  • 2.12.1. Turbocharger to remove and to fit
  • 2.12.2. To clean the impeller and compressor casing
  • 2.12.3. Engine breather assembly to renew
  • 2.13. Section 19 Lubrication System
  • 2.13.1. Oil filter canister to renew
  • 2.13.2. Engine lubricating oil to renew
  • 2.13.3. Filter head and oil cooler to remove and fit
  • 2.13.4. Sump to remove and to fit
  • 2.13.5. Oil strainer and suction pipe to remove and fit
  • 2.13.6. Lubricating oil pump to renew
  • 2.13.7. Lubrication oil pump to inspect
  • 2.13.8. Relief valve to remove, to fit and to renew
  • 2.14. Section 20 Fuel System
  • 2.14.1. Fuel filter element to renew
  • 2.14.2. Atomiser fault to inspect
  • 2.14.3. High pressure fuel pipes to remove and to fit
  • 2.14.4. Leak off rail to remove and to fit
  • 2.14.5. Atomisers to remove and to fit
  • 2.14.6. Fuel lift pump to remove and to fit
  • 2.14.7. Fuel lift pump to test
  • 2.14.8. Fuel injection pump to remove and to fit
  • 2.14.9. To eliminate air from fuel system
  • 2.14.10. Governor weight assembly to remove and to fit
  • 2.14.11. Speed control lever assembly to remove and to fit
  • 2.14.12. Speed control lever assembly to renew
  • 2.14.13. To change a plain bush to a threaded bush
  • 2.14.14. Fuel injection pump linkage to remove and to fit
  • 2.14.15. Fuel injection pump linkage to renew
  • 2.14.16. To record the maximum fuel position of the fuel control rack
  • 2.14.17. How to use the reference setting for maximum fuel
  • 2.15. Section 21 Cooling System
  • 2.15.1. To drain and to fill
  • 2.15.2. Thermostat to remove and to fit
  • 2.15.3. Thermostat to test
  • 2.15.4. Fan to remove and to fit
  • 2.15.5. Coolant pump to remove and to fit
  • 2.15.6. Oil cooler to remove and to fit
  • 2.16. Section 22 Flywheel System
  • 2.16.1. Flywheel to remove and to fit
  • 2.16.2. Flywheel to inspect
  • 2.16.3. Starter ring to remove and to fit
  • 2.16.4. Flywheel housing to remove and to fit
  • 2.17. Section 23 Electrical Equipment
  • 2.17.1. Drive belt to remove and to fit
  • 2.17.2. Alternator to remove and to fit
  • 2.17.3. Glowplugs (starting aid) to remove and to fit
  • 2.17.4. Glowplugs (starting aid) to check
  • 2.17.5. Starter motor to remove, to fit and to test
  • 2.17.6. Electrical stop solenoid to remove and to fit
  • 2.18. Section 24 Auxiliary Equipment
  • 2.18.1. Power takeoff assembly to remove and to fit
  • 2.18.2. Power takeoff assembly to dismantle and to assemble
  • 2.19. Section 25 Special Equipment
  • 2.19.1. List of special tools
Rate this product