Yanmar C12R-A, C30R-2A, C50R-3B Crawler Carrier Operation And Maintenance Manual

Yanmar C12R-A, C30R-2A, C50R-3B Crawler Carrier Operation And Maintenance Manual - Image 2

Yanmar C12R-A, C30R-2A, C50R-3B Crawler Carrier Operation And Maintenance Manual - Image 3

Yanmar C12R-A, C30R-2A, C50R-3B Crawler Carrier Operation And Maintenance Manual - Image 4

Yanmar C12R-A, C30R-2A, C50R-3B Crawler Carrier Operation And Maintenance Manual - Image 5

yanmar c12r a c30r 2a c50r 3b crawler carrier operation and maintenance manual 2

yanmar c12r a c30r 2a c50r 3b crawler carrier operation and maintenance manual 3

Yanmar C12R-A, C30R-2A, C50R-3B Crawler Carrier Operation And Maintenance Manual

$20.00

Type Of Manual: Operation And Maintenance Manual
Number of Pages: 264
Size: 16.0MB
Format: PDF

Category: Yanmar Operator Manual PDF

Model List:
- C12R-A, C30R-2A, C50R-3B Crawler Carrier

1. Introduction
2. Safety information
3. Product overview and regulation
3.1. Intended uses
3.2. Operation license
4. Ordering replacement parts and service call
4.1. Location of machine serial number plate
4.2. Location of engine serial number plate
4.3. Location of the EPA identification plate
4.4. Ordering replacement parts and service calls
4.5. Basic precautions
4.6. Operating precautions
4.6.1. Break in period
4.6.2. Precautions before starting the engine
4.6.3. Precautions when traveling
4.6.4. Precautions when working
4.6.5. Precautions for parking
4.6.6. Precautions for transportation
4.6.7. Precautions for the battery
4.7. Precautions for servicing
4.7.1. Precautions before servicing
4.7.2. Replacing essential parts periodically
4.7.3. Precautions during servicing
4.8. Safety messages (warning labels)
4.8.1. Location of warning labels C12R-A
4.8.2. Location of warning labels C30R-2A
4.8.3. Location of warning labels C50R-3B
5. OPERATION
5.1. Identification of important parts
5.1.1. Overview of the machine C12R-A
5.1.2. Controls and switches C12R-A
5.1.3. Overview of the machine C30R-2A
5.1.4. Controls and switches C30R-2A
5.1.5. Overview of the machine C50R-3B
5.1.6. Controls and switches C50R-3B
5.2. Description of operators area for C12R-A
5.2.1. Monitor
5.2.2. Switches
5.2.3. Control levers and pedals
5.2.4. Engine hood
5.2.5. Storage compartment for the operation maintenance manual
5.2.6. Fuses
5.2.7. Fuel cap
5.2.8. Wagon support
5.3. Description of operators area for C30R-2A
5.3.1. Monitor
5.3.2. Switches
5.3.3. Control levers and pedals
5.3.4. Engine hood
5.3.5. Storage for tools and the operation maintenance manual
5.3.6. Fuse box and fusible link
5.3.7. Operators seat
5.3.8. Dump deck support stopper
5.4. Description of operators area for C50R-3B
5.4.1. Monitor
5.4.2. Switches
5.4.3. Control levers
5.4.4. Engine hood
5.4.5. Side cover
5.4.6. Battery cover
5.4.7. Cabin
5.4.8. Storage for tools and the operation maintenance manual
5.4.9. Fuse box
5.4.10. Fuel cap
5.4.11. Operators seat
5.4.12. Wagon stopper
5.5. Operating Instructions for C12R-A
5.5.1. Checking before starting the engine
5.5.2. Operating and checking instructions before starting up the engine
5.5.3. Starting up the engine
5.5.4. Operating and checking instructions after starting the engine
5.5.5. Traveling
5.5.6. Steering (turning the machine)
5.5.7. Stopping the machine
5.5.8. Dumping the wagon
5.5.9. Precautions for working
5.5.10. Precautions for going up and down a slope
5.5.11. Removal of wagon flaps
5.5.12. Parking the machine
5.5.13. Inspection requirements after completing operation
5.5.14. Stopping the engine
5.5.15. Inspection requirements after stopping the engine
5.5.16. Locking
5.5.17. Handling the rubber crawlers
5.6. Operating Instructions for C30R-2A
5.6.1. Checking before starting the engine
5.6.2. Operating and checking instructions before starting up the engine
5.6.3. Starting up the engine
5.6.4. Operating and checking instructions after starting the engine
5.6.5. Traveling
5.6.6. Steering
5.6.7. Stopping the machine
5.6.8. Dumping
5.6.9. Precautions for working
5.6.10. Precautions for going up and down a slope
5.6.11. Removal of wagon flaps
5.6.12. Parking the machine
5.6.13. Inspection requirements after completing operation
5.6.14. Stopping the engine
5.6.15. Inspection requirements after stopping the engine
5.6.16. Locking
5.6.17. Handling the rubber crawlers (for machines equipped with rubber)
5.7. Operating Instructions for C50R-3B
5.7.1. Checking before starting the engine
5.7.2. Operating and checking instructions before starting up the engine
5.7.3. Starting up the engine
5.7.4. Operating and checking instructions after starting the engine
5.7.5. Traveling
5.7.6. Steering
5.7.7. Stopping the machine
5.7.8. Dumping the wagon
5.7.9. Swinging the wagon (for the swing wagon type)
5.7.10. Precautions for working
5.7.11. Precautions for going up and down a slope
5.7.12. Removal of wagon flaps
5.7.13. Parking the machine
5.7.14. Inspection requirements after completing operation
5.7.15. Stopping the engine
5.7.16. Inspection requirements after stopping the engine
5.7.17. Locking
5.7.18. Handling the rubber crawlers
5.8. Transportation
5.8.1. Loading and unloading the machine
5.8.2. Precautions for loading the machine
5.8.3. Suspending the machine (only for C12R-A and C30-2A)
5.9. Care in cold weather and long-term storage
5.9.1. Preparing for cold weather
5.9.2. Long-term storage
5.10. Troubleshooting
5.10.1. Phenomena that are not breakdowns
5.10.2. Precautions for operation in water
5.10.3. If the battery is overdischarged
5.10.4. Troubleshooting (depending on model)
6. MAINTENANCE
6.1. Precautions for servicing
6.2. Basic servicing practices
6.2.1. Filter
6.3. Fueling, oiling and greasing based on temperature range
6.3.1. Fuel and oil
6.3.2. Cooling water
6.4. Standard tightening torque for bolts and nuts
6.4.1. Torque table
6.5. Maintenance table
6.5.1. List of periodic inspection and servicing
6.6. Procedures of maintenance for C12R-A
6.6.1. Checking the rubber crawlers
6.6.2. Replacing the rubber crawler
6.6.3. Adjusting the fan belt tension
6.6.4. Adjusting the drive belt tension
6.6.5. Checking, cleaning and replacing the air cleaner element
6.6.6. Draining the water and deposits from the fuel tank
6.6.7. Cleaning the fuel filter element (with water separator)
6.6.8. Replacing the fuel filter element
6.6.9. Replacing the pre-filter
6.6.10. Replacing the engine oil and the engine oil filter
6.6.11. Replacing the hydraulic oil and cleaning the suction filter
6.6.12. Replacing the hydraulic oil return filter
6.6.13. Adjusting the steering clutches
6.6.14. Adjusting the steering brakes
6.6.15. Adjusting the travel pedal
6.6.16. Adjusting the F/R lever
6.7. Procedures of maintenance for C30R-2A
6.7.1. Checking the rubber crawlers
6.7.2. Replacing the rubber crawler
6.7.3. Adjusting the fan belt tension
6.7.4. Checking, cleaning and replacing the air cleaner element
6.7.5. Draining the water and deposit in the fuel tank
6.7.6. Checking the water separator
6.7.7. Cleaning the water separator element
6.7.8. Cleaning / replacing the fuel filter element
6.7.9. Replacing the engine oil and the engine oil filter
6.7.10. Replacing the oil in the hydraulic oil tank and cleaning the suction filter
6.7.11. Replacing the return oil filter
6.7.12. Checking and replenishing the transfer case oil
6.7.13. Replacing the transfer case oil
6.7.14. Checking and cleaning the oil filter in the transfer case
6.7.15. Replacing the final case oil
6.7.16. Greasing the final drive
6.8. Procedures of maintenance for C50R-3B
6.8.1. Checking the rubber crawlers
6.8.2. Checking the rubber crawler tension
6.8.3. Replacing the rubber crawler
6.8.4. Adjusting the fan belt tension
6.8.5. Checking, cleaning and replacing the air cleaner
6.8.6. Draining the water and deposits from the fuel tank
6.8.7. Checking the water separator
6.8.8. Draining and cleaning the water separator
6.8.9. Cleaning / replacing the fuel filter element
6.8.10. Replacing the engine oil and the engine oil filter element
6.8.11. Replacing the hydraulic oil and cleaning the suction filter element
6.8.12. Replacing the return filter
6.8.13. Replacing the line filter element
6.8.14. Replacing the travel reduction gear oil
6.8.15. Checking and replenishing the windshield washer fluid (for cabin)
7. SPECIFICATIONS
7.1. Specifications
7.1.1. Specifications
7.1.2. Model view and working range for C12R-A
7.1.3. Model view and working range for C30R-2A
7.1.4. Model view and working range for C50R-3B
7.1.5. Noise emitted by the machines
7.1.6. Vibrations emitted by the machines
7.2. Options
7.2.1. Options
7.3. Hydraulic and wiring diagrams
7.3.1. Hydraulic diagrams
7.3.2. Wiring diagrams
7.4. Maintenance
7.5. Notes

Rate this product