Yanmar ZT370 Stern Drive Operation Manual

Yanmar ZT370 Stern Drive Operation Manual - Image 2

Yanmar ZT370 Stern Drive Operation Manual - Image 3

Yanmar ZT370 Stern Drive Operation Manual - Image 4

Yanmar ZT370 Stern Drive Operation Manual - Image 5

yanmar zt370 stern drive operation manual 2

yanmar zt370 stern drive operation manual 3

Yanmar ZT370 Stern Drive Operation Manual

$20.00

Type Of Manual: Operation Manual
Number of Pages: 60
Size: 8.0MB
Format: PDF

Category: Yanmar Operator Manual PDF

Model List:
- ZT370 Stern Drive

1. English
2. Table of Contents
3. Introduction
3.1. Record of Ownership
3.2. Safety Precautions
3.2.1. General Information
3.2.2. Before You Operate
3.2.3. During Operation and Maintenance
4. Product Overview
4.1. Overview
4.1.1. Owner/Operator Responsibilities
4.1.2. New Stern-Drive Break-In
4.1.3. Dealer/Distributor Responsibilities
4.2. Component Identification
4.3. Corrosion Protection
4.3.1. Galvanic Corrosion
4.3.2. Corrosion Control
4.3.3. Shore Power
4.3.4. Underwater Drive Coating
4.3.5. Additional Protection
4.3.6. Gear Housing Anodic Plates
4.3.7. Ventilation Plate Anode
4.3.8. Trim Cylinder Anodes
4.3.9. Propeller Shaft Anode
4.4. Features and Controls
4.4.1. Remote Controls
4.4.2. Power Trim
4.4.3. Stern-Drive Trim Angle
4.4.4. Trim and Tilt/Trailering Switch
4.4.5. Electrical System
5. Stern-Drive Operation
5.1. Propeller Selection
5.2. Installing the Propellers
5.3. Removing the Propeller
5.4. Daily Checks
5.4.1. Visual Checks
5.4.2. Check the Stern-Drive Oil Level
5.4.2.1. Fill the stern-drive with oil
5.4.3. Check the Power Trim Pump Fluid
5.4.3.1. Fill the power trim pump fluid
6. Maintenance
6.1. Periodic Maintenance
6.1.1. The Importance of Periodic Maintenance
6.1.2. Performing Periodic Maintenance
6.1.3. The Importance of Daily Checks
6.1.4. Yanmar Replacement Parts
6.1.5. Tools Required
6.1.6. Ask Your Authorized Yanmar Marine Dealer or Distributor for Help
6.2. Tightening Fasteners
6.3. Torque Charts
6.3.1. Standard Torque Values
6.3.2. Torque Specifications
6.4. Periodic Maintenance Table
6.5. General Inspection
6.6. Power Trim Pump Fluid
6.7. Periodic Maintenance Procedures
6.7.1. Checking the water inlets
6.7.2. Checking the seawater inlet hole
6.7.3. Inspecting the anodes
6.7.4. Checking the oil level
6.7.5. After Initial 50 Hours of Operation
6.7.5.1. Lubricating the engine coupler
6.7.5.2. Changing the stern-drive oil
6.7.6. Every 50 Hours of Operation
6.7.6.1. Lubricate the engine coupler
6.7.7. Every 100 Hours of Operation
6.7.7.1. Lubricating the propeller shaft and retorqueing the nut
6.7.7.2. Retorqueing the gimbal ring to steering shaft connection
6.7.7.3. Inspecting the bellows and the clamps
6.7.7.4. Checking the engine alignment
6.7.7.5. Lubricating the steering shaft bushing
6.7.7.6. Lubricating the unit bearing (gimbal housing)
6.7.7.7. Lubricating the engine coupler
6.7.7.8. Checking the circuit for loose or damaged connections
6.7.7.9. Testing the Y-CaPS unit output
6.7.7.10. Checking the steering system for loose, missing or damaged parts
6.7.7.11. Checking the remote control for loose, missing or damaged parts
6.7.7.12. Lubricating the shift cable and the linkages
6.7.8. Every 150 Hours of Operation
6.7.8.1. Changing the stern-drive oil (Light duty commercial applications only)
6.7.9. Every 250 Hours of Operation
6.7.9.1. Touching-up the stern-drive paint and spray with corrosion guard
6.7.9.2. Retorqueing the rear engine mounts
6.7.9.3. Changing the stern-drive oil
6.7.10. Every 1000 Hours of Operation
6.7.10.1. Replace of friction disc (Light duty commercial applications only)
6.7.11. Every Year
6.7.11.1. Retorqueing the gimbal ring to steering shaft connection
6.7.11.2. Inspecting the bellows and the clamps
6.7.11.3. Checking the engine alignment
6.7.11.4. Lubricating the steering shaft bushing
6.7.11.5. Lubricating the unit bearing (gimbal housing)
6.7.11.6. Lubricating the engine coupler
6.7.11.7. Checking the circuit for loose or damaged connections
6.7.11.8. Testing the Y-CaPS unit output
6.7.11.9. Checking the steering system for loose, missing or damaged parts
6.7.11.10. Checking the remote control for loose, missing or damaged parts
6.7.11.11. Lubricating the cable and the linkages
6.7.11.12. Touching-up the stern-drive paint and spray with corrosion guard
6.7.11.13. Changing the stern-drive oil
6.7.11.14. Retorqueing the rear engine mounts
6.7.11.15. Replace of friction disc (Light duty commercial applications only)
6.7.12. Every 2 Years
6.7.12.1. Replace U-joint bellows
6.7.12.2. Replace control cable bellows
7. Troubleshooting
8. Long-Term Storage
8.1. Cold Weather (Freezing Temperature), Seasonal and Extended Storage
8.1.1. Stern-Drive Lay Up
8.1.2. Stern-Drive Recommissioning
9. Specifications

Rate this product