Claas Tucano 450-440 (L35) Combines Operator Manual ES

File List:

00 0302 531 2.pdf
00 0302 637 6.pdf

00 0302 531 2.pdf:

TUCANO 580 / 570 / 560TUCANO 450 / 430MONTANA
1. Introduction
1.1 Information regarding the instruction manual
1.1.1 Validity of the manual
2 Security
2.1 Safety instructions on the machine
2.1.1 Cab hazard graphic symbols
2.1.2 Graphic danger symbols of the power supply unit
3 Machine Description
3.1 Summary and operation
3.1.1 MONTANA Summary
3.2 Identification plates and identification numbers
3.2.1 Drive axle identification plate
4 Control and display instruments
4.1 Cabin and driving position
4.1.1 Control desk
4.1.2 MONTANA command field
5 Technical data
5.1 TUCANO 580 / 570 / 560 / 450 / 430 MONTANA
5.1.1 Machine dimensions
5.1.2 Machine weights
Machine weight
Option weight
5.1.3 Measurements of the grain tank discharge pipe in working position
5.1.4 Turning diameter
Measurement conditions
5.1.5 Sound pressure level and vibrations
5.1.6 Diesel engine of the machine
5.1.7 Mercedes-Benz OM 936 LA.E5 diesel engine
5.1.8 Hydrostatic propulsion
5.1.9 Leveling chassis
5.1.10 Summary of drive axle track widths
5.1.11 Summary of steering axle track widths
5.1.12 Track width table 01
5.1.13 Track width table 02
5.1.14 Track width table 03
5.1.15 Track width table 04
5.1.16 Track width table 05
5.1.17 Track width table 06
5.1.18 Track width table 07
5.1.19 Brake
5.1.20 Mercedes-Benz OM 936 LA.E5 diesel engine battery
5.1.21 Width of the shelling cylinder of the machine
5.1.22 Machine threshing system
5.1.23 Threshing units with APS threshing system
5.1.24 Machine separation system
5.1.25 Rotor separation system
5.1.26 Shaker separation system
5.1.27 Cleaning
5.1.28 Unloading of the harvest and unloading of the straw
5.1.29 Grain tank volume
5.1.30 Grain tank discharge performance
5.1.31 Central lubrication system*
5.2 Inputs
5.2.1 Lubricants
5.2.2 Hydraulic oils
6 Preparation of the machine
6.1 Turn off the machine and secure it
6.1.1 Turn off the machine and secure it
6.2 Prepare the machine for driving
6.2.1 Prepare for road traffic
6.2.2 Prepare the field trip
6.3 Power supply unit
6.3.1 Check the anti-slip strips on the feed channel
6.4 Chassis
6.4.1 Raise the machine on supports
6.4.2 Remove and install the wheels
Remove the wheels
Mount the wheels
Learn impulses per 100 m
6.4.3 Procedure to follow for adjusting the track width of the steering axle
6.4.4 Changing the steering axle from transport position to working position
6.4.5 Raise the machine on supports to tilt the steering axle
6.4.6 Adjust the track width of the steering axle
6.4.7 Adjust the track width of the steering axle
6.4.8 Select the holes in the adjustment body
6.5 Assembly and body parts
6.5.1 Mount additional weight to the machine
6.5.2 Mounting the additional weights for folding heads
7 Management
7.1 Driving the machine
7.1.1 Driving the machine
Drive the machine forward
Brake the machine
Stop the machine
Drive the machine in reverse
7.2 Head
7.2.1 Adjust the cutting angle
7.3 Chassis
7.3.1 Select MONTANA operating mode
7.3.2 Lower the machine to the transport position
7.3.3 Control MONTANA functions
Control MONTANA functions on flat ground
7.3.4 Switching MONTANA automatic operation on and off
Connect MONTANA automatic operation
Disconnecting automatic operation of MONTANA
7.3.5 Connecting and disconnecting the MONTANA manual control
7.3.6 Shift into gear
7.3.7 Switching OVERDRIVE* operating mode on and off
7.3.8 Engaging and disengaging the differential lock
7.3.9 Towing the machine from the danger zone
7.4 Brake
7.4.1 Engaging and disengaging the brake pedals
8 Incident and solution
8.1 Chassis
8.1.1 Chassis fault summary
8.2 Electrical and electronic system
8.2.1 Summary of MONTANA automatic operation malfunctions
9 Maintenance
9.1 Summary of maintenance intervals
9.1.1 Before starting the harvest
9.1.2 After the first 100 hours of service
9.1.3 After the first 500 hours of service
9.1.4 Every 10 hours of service or daily
9.1.5 Every 50 hours of service
9.1.6 Every 100 hours of service
9.1.7 Every 250 hours of service
9.1.8 Every 500 hours of service
9.1.9 Every 500 hours of service or annually
9.1.10 Every 1000 hours of service
9.1.11 Annually
9.2 Greasing scheme
9.2.1 Grease the grease fittings every 100 operating hours on the left
9.2.2 Grease the lubrication points every 100 operating hours on the right
9.2.3 Lubricate the left grease points annually
9.2.4 Lubricate the right grease points annually
9.3 Chassis
9.3.1 Remove and install the MONTANA drive axle reinforcement plate
9.3.2 Lubricate the rolling crowns with balls of the wheel connecting rods in compliance with lubrication standards
9.3.3 Check the oil level of the drive axle gearbox
9.3.4 Change the drive axle gearbox oil
Drain oil
Fill oil
9.3.5 Check the oil level of the drive axle carrier
9.3.6 Change the oil in the drive axle carriers
Drain oil
Fill oil
9.3.7 Check the oil level of the connecting rods of the drive axle wheels
9.3.8 Change the oil in the connecting rods of the drive axle wheels
Drain oil
Fill oil
9.4 Brake
9.4.1 Check the brake cylinder bleeder
9.5 Hydraulic installation
9.5.1 Check the hydraulic oil level
9.5.2 Change hydraulic oil and filters
Drain oil
Fill oil
9.6 Power supply unit
9.6.1 Bleed the hydraulic cylinder of the headstock transverse adjustment