Claas Tucano 460 (837) Combines Technical System EN

File List:

00 0291 027 2.pdf
00 0302 343 1.pdf
CHP-numbers for connectors CLAAS HARNESS PARTS.pdf

00 0291 027 2.pdf:

MB OM460LAMB OM502LAMB OM906LAMB OM926LA
Table of contents
CCN explanation
CCN (CLAAS Component Number)
Electric systems standard
Overview
Hydraulic system standard
Overview
CCN (CLAAS Component Number)
Introduction
Safety rules
Safety and hazard precautions
Validity of manual
Validity of manual
01 Engine
0125 Injection / Fuel system
Injection / fuel system PLD
PLD injection system
Description of function
Pumping phases of plug-on pump
Description of function
Control of plug-on pump
Description of function
Classification of plug-on pumps
Example of a plug-on pump identification plate
Elements in example of plug-on pump identification plate
Fuel low-pressure measurement
Special tool
Preparation of fuel low-pressure measurement
Description of function
Measuring values, fuel low-pressure (downstream of fuel filter)
0155 Engine control
Diesel engine monitoring, diesel engine (MB TIER 3) TUCANO, JAGUAR
Measured values table
Description of function
Diesel engine monitoring, diesel engine (MB TIER 3) LEXION
Measured values table
Description of function
Diesel engine monitoring, diesel engine (MB TIER 4i) TUCANO, JAGUAR
Measured values table
Description of function
Limitation of torque in case of lack of urea
Description of function
Limitation of torque in case of insufficient urea quality
Description of function
Torque limitation after exceeding the time with system faults
Description of function
Diesel engine monitoring, diesel engine (MB TIER 4i) LEXION
Measured values table
Description of function
Limitation of torque in case of lack of urea
Description of function
Limitation of torque in case of insufficient urea quality
Description of function
Torque limitation after exceeding the time with system faults
Description of function
0165 Exhaust gas aftertreatment
Compressed-air system of MB TIER 4i (LEXION, TUCANO)
Description of function
Air dryer with integrated pressure controller
Description of function
Compressed air system MB TIER 4i (JAGUAR)
Description of function
Air dryer with integrated pressure controller
Description of function
SCR system – Urea heating and injection
Description of function
Combined filling level / urea temperature sensor
Description of function
Urea pump unit
Description of function
Reduction catalyst temperature sensors
Description of function
Dosing unit
Description of function
NOx sensor
Description of function
Combined intake air humidity and temperature sensor
Description of function
10 Electrical / Electronic equipment
1012 Modules / sensors
Module overview – MB (OM460LA, 502LA, 906LA, 926LA)
Key to diagram
Module A015 – Electronic engine control (ECM) – MB TIER 4i
Connector X1
Key to diagram
Module pin assignment, connector X1
Connector X2, sheet 1 of 2, 6-cylinder inline and V8 engine
Module pin assignment, connector X2 sheet 1 of 2
Connector X2, sheet 2 of 2, 6-cylinder inline engine
Module pin assignment, connector X2 sheet 2 of 2, 6-cylinder inline engine
Connector X2, sheet 2 of 2, V8 engine
Module pin assignment, connector X2 sheet 2 of 2, V8 engine
Module A017 – Engine adaptation module (ADM) – MB TIER 3
Key to diagram
Key to diagram
Module A017 – Engine adaptation module (ADM) – MB TIER 4i
Key to diagram
Key to diagram
Module A032 – Reduction catalyst (SCR) – MB TIER4i
Key to diagram
Key to diagram
Sensors MB OM460LA
Figure of sensors
Sensors on MB 502LA
Figure of sensors
Sensors on MB OM 906LA, OM 926LA
Figure of sensors
1085 Networks
BUS system (CAN) – engine and machine
Description of function
92 Diagnosis
Diagnosis by fault codes
9220 Error codes engine (J1939)
FMI failure code (Failure Mode Indicator)
FMI failure code (Failure Mode Indicator)
FMI 00 (Signal too high)
FMI 01 (Signal too low)
FMI 02 (Erratic signal)
FMI 03 (Voltage too high)
FMI 04 (Voltage too low)
FMI 05 (Current too low)
FMI 06 (Current too high)
FMI 07 (Mechanical failure)
FMI 08 (Abnormal frequency signal)
FMI 09 (Communication error)
FMI 10 (Rate of signal change too fast)
FMI 11 (multiple faults)
FMI 12 (ECU defective)
FMI 13 (Signal outside of calibration range)
FMI 16 (Parameter not available)
FMI 17 (ECU not responding)
FMI 18 (Power supply failure)
FMI 19 (Software conditions not met)
FMI 95 (no signal change)
FMI 96 (CAN Bus system defective)
FMI 97 (Erratic condition)
FMI 98 (Warning)
FMI 99 (Info)
Fault codes
Diesel engine J1939 (MB) fault code list
Description of function

00 0302 343 1.pdf:

PROFI CAM 3
Table of contents
General information
Marking of warnings and hazard prevention notes
First-aid measures
CCN explanation
CCN (CLAAS Component Number)
Electric system standard
Overview
Hydraulic system standard
Overview
CCN (CLAAS Component Number)
10 Electrical / Electronic equipment
1030 Board computer / Indicators
Camera system
Description of function
1097 Testing / Measuring / Adjusting
Testing / measuring / adjusting the PROFI CAM
Checking the fuse in the video channel select box (C102)
Testing the video camera connector (C055)
1098 Fault / remedy
Fault / remedy PROFI CAM
The video monitor (C101) shows no image or cannot be switched on (indicator light fails to light up)
Video monitor (C102) displays a blue image either permanently or temporarily
The video monitor image is blurred
Replacing the fuse in the video channel select box (C102)
Connection and connecting cable with video camera (C055)

CHP-numbers for connectors CLAAS HARNESS PARTS.pdf:

CLAAS HARNESS PARTS
Table of contents
10 Electrical / Electronic equipment
1081 Overview of connectors
CLAAS HARNESS PARTS (CHP)