Bomag BF 700 C S500 Paver Service Manual 00840008

Bomag BF 700 C S500 Paver Service Manual 00840008 - Image 2

Bomag BF 700 C S500 Paver Service Manual 00840008 - Image 3

Bomag BF 700 C S500 Paver Service Manual 00840008 - Image 4

Bomag BF 700 C S500 Paver Service Manual 00840008 - Image 5

bomag bf 700 c s500 paver service manual 00840008 2

bomag bf 700 c s500 paver service manual 00840008 3

Bomag BF 700 C S500 Paver Service Manual 00840008

$30.00

Type Of Manual: Service Manual
Manual ID: 00840008
Format: PDF
Size: 32.5MB
Number of Pages: 456
Serial Number:
821892061001 and up

Category: Bomag Service Manual PDF

Model List:
- BF 700 C S500 Paver

1. Table of contents
2. General
2.1. Introduction Service Manual
2.2. Concerning your safety
2.2.1. Handling fuels and lubricants
2.2.1.1. Preliminary remarks
2.2.1.2. Safety regulations and environmental protection regulations for handling diesel fuel
2.2.1.3. Safety regulations and environmental protection regulations for handling AdBlue/DEF
2.2.1.4. Safety regulations and environmental protection regulations for handling oil
2.2.1.5. Safety regulations and environmental protection regulations for handling hydraulic oil
2.2.1.6. Safety regulations and environmental protection regulations for handling coolants
2.2.1.7. Safety regulations and environmental protection regulations for handling battery acid
2.2.2. Parking the machine in secured condition
2.3. Fuels and lubricants
2.3.1. Engine oil
2.3.1.1. Oil quality
2.3.1.2. Oil viscosity
2.3.1.3. Oil change intervals
2.3.2. Fuel
2.3.2.1. Fuel quality
2.3.2.2. Winter fuel
2.3.2.3. Storage
2.3.3. AdBlue/DEF
2.3.3.1. AdBlue/DEF quality
2.3.3.2. Low outside temperatures
2.3.3.3. Storage
2.3.3.4. Cleanliness
2.3.4. Coolant
2.3.4.1. General
2.3.4.2. Topping up coolant
2.3.4.3. Replacing coolant
2.3.5. Hydraulic oil
2.3.5.1. Mineral oil based hydraulic oil
2.3.5.2. Biodegradable hydraulic oil
2.3.6. Gear oil SAE 75W90
2.3.7. Lubrication grease
2.3.8. Hightemperature lubrication grease
2.4. List of fuels and lubricants
2.5. Repair notes for hydraulics
3. Technical data
4. Total overview of machine
4.1. Component overview electrics
4.2. Component overview wiring looms
4.3. Component overview hydraulics
5. Troubleshooting
5.1. Overviews
5.1.1. Overview Travel system
5.1.2. Overview Material Transport
5.1.3. Overview Screed Functions
5.2. Codes General Information
5.3. Fault codes
5.3.1. Foreword
5.3.2. Fault code list
5.3.3. Fault Rectification
6. Electrics
6.1. Control Units
6.1.1. Software Updating
6.2. Display
6.2.1. LCDisplay unit
6.3. Input codes
6.3.1. Resetting to factory settings
6.3.2. Travel Control (Travel Functions)
6.3.2.1. Automatic Calibration Of Currents In Travel System
6.3.2.2. Calibrating the travel system manually
6.3.2.3. Travel signal by push button for partial screed relief
6.3.2.4. Steering with toggle button for track control, should the steering encoder be defective
6.3.2.5. Changing the type of speed potentiometer
6.3.2.6. Driving against the closed brake
6.3.2.7. Activating/deactivating the screed heating in low idle speed
6.3.2.8. Activating/deactivating the cleaning function
6.3.2.9. Activating/deactivating the charge pressure relief valve
6.3.2.10. Managing settings
6.3.3. Screed control (screed functions)
6.3.3.1. Calibrating the LCSfunction
6.3.3.2. Activating/deactivating the twin LCS
6.3.3.3. Calibrating tamper pump currents
6.3.3.4. Changing the tamper start and stop ramp
6.3.3.5. Calibrating vibration pump currents
6.3.3.6. Managing settings
6.3.4. Material flow control
6.3.4.1. Activating/deactivating the hydraulic front hopper wing
6.3.4.2. Calibrating auger pump currents
6.3.4.3. Changing the auger start and stop ramp
6.3.4.4. Calibrating scraper belt pump currents
6.3.4.5. Enable/disable lifting the auger block together with the screed
6.3.4.6. Managing settings
6.3.5. Managing the fault log
6.3.6. Read out fault codes MTU
6.4. Replacement of electrical components
6.4.1. Control system
6.4.2. Travel pump
6.4.3. Pump for the auger drive
6.4.4. Pump for the scraper belt drive
6.4.5. Pump for the tamper drive
6.4.6. Pump for the vibration drive
6.4.7. Components without adjustment/teach procedure
7. Engine MTU 4R 1000 4final
7.1. Diesel engine description
7.2. Oil circuit
7.3. Cooling circuit
7.4. Fuel system
7.5. Exhaust gas cleaning
7.5.1. Exhaust gas recirculation
7.6. Engine electrics
7.6.1. Control unit MTU
8. Hydraulic system
8.1. Hydraulics fundamentals
8.2. Routing of hydraulic hoses
8.2.1. Hoses for travel functions
8.2.2. Hoses for radiator
8.2.3. Hoses for scraper belt
8.2.4. Hoses for auger
8.2.5. Hoses for tamper vibration
9. Assembly groups
9.1. Tractor
9.1.1. General
9.1.2. Travel system
9.1.3. Drivers stand
9.2. Material transport
9.2.1. Hopper
9.2.2. Scraper belt
9.2.3. Augers
9.2.4. Tunnel
9.2.5. Side plates
9.2.6. Inspection and maintenance work
9.2.6.1. Material transport
9.2.6.2. Every 250 operating hours
9.2.6.2.1. Servicing the scraper belt
9.2.6.2.2. Servicing the scraper belt drive chain
9.2.6.2.3. Servicing the auger
9.2.6.2.4. Checking scraper and rubber apron on material hopper
9.2.6.3. Every 500 operating hours
9.2.6.3.1. Checking the hydraulic lines
9.2.6.4. As required
9.2.6.4.1. Extending auger and tunnel
9.3. Screed S500
9.3.1. Precautions for safe work with raised screed
9.3.2. Description
9.3.3. Basic settings on the screed
9.3.3.1. To be observed before adjusting the screed
9.3.3.2. Basic settings screed S500/600
9.3.4. Assembling the screed extensions
9.4. Screed heating
9.4.1. Description
9.4.2. Screed heating commissioning
9.4.3. Faults in the electric heating
10. Appendix
10.1. A Wiring diagram 251
10.2. B Wiring diagram screed S500
10.3. C Hydraulic diagram BF700C

Rate this product