Bomag BF 800 C Road Finisher Service Training 00891992

Bomag BF 800 C Road Finisher Service Training 00891992 - Image 2

Bomag BF 800 C Road Finisher Service Training 00891992 - Image 3

Bomag BF 800 C Road Finisher Service Training 00891992 - Image 4

Bomag BF 800 C Road Finisher Service Training 00891992 - Image 5

bomag bf 800 c road finisher service training 00891992 2

bomag bf 800 c road finisher service training 00891992 3

Bomag BF 800 C Road Finisher Service Training 00891992

$30.00

Type Of Manual: Service Training
Manual ID: 00891992
Format: PDF
Size: 39.4MB
Number of Pages: 700
Serial Number:
821837171001, 821837711001, 821837191001, 821837661001

Category: Bomag Service Manual PDF

Model List:
- BF 800 C Road Finisher

1. BF 800_C
1.1. BF 800_C
2. General
2.1. General
2.2. Introduction
2.3. General
2.4. General
2.5. Transport work with cranes and lifting tackle
2.6. Precautions and codes of conduct for welding work
2.7. Operation of highvoltage systems
2.8. Old oils
2.9. Hydraulics
2.10. Hot fuels
2.11. Synthetic rubber
2.12. Poisonous substances
2.13. Battery
2.14. Special safety regulations
2.15. The values specified in the table apply for screws
2.16. The values specified in the table apply for screws
2.17. The values specified in the table apply for screws
2.18. The values specified in the table apply for screws
2.19. The values specified in the table apply for screws
2.20. The values specified in the table apply for screws
2.21. The values specified in the table apply for screws
2.22. The values specified in the table apply for screws
2.23. The values specified in the table apply for screws
2.24. The values specified in the table apply for screws
2.25. The values specified in the table apply for screws
2.26. The values specified in the table apply for screws
2.27. The values specified in the table apply for screws
2.28. The values specified in the table apply for screws
3. Technical data
3.1. Technical data
3.2.
3.3.
4. Maintenance
4.1. Maintenance
4.2. General notes on maintenance
4.3. Fuels and lubricants
4.4. Coolant
4.5. Mineral oil based hydraulic oil
4.6. Gear oil
4.7. Lubrication grease
5. EPlan wiring diagrams
5.1. EPlan wiring diagrams
6. Engine
6.1. Engine
6.2. Checking the engine oil level
6.3. Checking the engine oil level
6.4. Changing engine oil and oil filter cartridge
6.5. Replacing the fuel prefilter cartridge, bleed the fuel system
6.6. Replace the fuel filter
6.7. Check, clean the water separator
6.8. Check the coolant level
6.9. Replace the coolant
6.10. Air filter maintenance
6.11. Air filter maintenance
6.12. Clean the cooling fins on engine and hydraulic oil cooler
6.13. Intercooler, drain off oil and condensation water
6.14. Adjust the valve clearance
6.15. Checking the ribbed Vbelt, replacing if necessary
6.16. Replace the crank case ventilation valve
6.17. Engine conservation
7. Engine electrics
7.1. Engine electrics
8. Electrics
8.1. Electrics
8.2. Service the battery, check the main battery switch
8.3. Starting the engine with jump leads
8.4. Starting with jump wires
8.5.
8.6. Component overview Electrics
8.7. View of control panel
8.8. View of control panel
8.9. View of control panel
9. Error codes general information
9.1. Error codes general information
10. Input codes
10.1. Input codes
11. Replacement of components
11.1. Replacement of components
12. Material hopper, description
12.1. Material hopper, description
13. Vibrating screed, description
13.1. Vibrating screed, description
14. Basic settings on the screed
14.1. Basic settings on the screed
14.2. Bringing the straight crossfalls to zero position
14.3. Bringing the straight crossfalls to zero position
14.4. Aligning basic screed and mobile sections
15. Assembling the screed extensions
15.1. Assembling the screed extensions
15.2. Assembling the screed extensions
15.3. Assembling the screed extensions
16. Electric screed heating, repair
16.1. Electric screed heating, repair
16.2. Faults in the electric heating
16.3. Faults in the electric heating
16.4. Faults in the electric heating
17. Travel drive, description
17.1. Travel drive, description
18. Hydraulics
18.1. Hydraulics
18.2. Component overview hydraulics
18.3. Component overview hydraulics
18.4. Variable displacement pumps, A4VG28EP to A4VG180EP
18.5. Variable displacement pumps, A4VG28EP to A4VG180EP
18.6. Travel pump viewed on the machine
18.7. Travel pump viewed on the machine
18.8. Variable displacement pumps, A10VG28/45/56 EP
18.9. Side plates viewed on the machine
18.10. Side plates viewed on the machine
18.11. Axial piston pumps, A10VO/VSO 18 to 100 DFR1
18.12. Axial piston pumps, A10VO/VSO 18 to 100 DFR1
18.13. Pump for fan drive viewed on the machine
18.14. Pump for fan drive viewed on the machine
18.15. External gear pumps
18.16. External gear pumps
18.17. Multiple gear pumps
18.18. Check the hydraulic oil level
18.19. Change hydraulic oil and hydraulic oil filter
19. Hydraulics travel circuit
19.1. Hydraulics travel circuit
19.2. Travel circuit
19.3. Travel circuit
20. Hydraulics material transport
20.1. Hydraulics material transport
20.2. Scraper belts
20.3. Scraper belts
20.4. Conveyor augers
20.5. Conveyor augers
20.6. Tamping
20.7. Tamping
20.8. Vibrate
20.9. Vibrate
21. Hydraulics Service
21.1. Hydraulics Service
21.2. Fan circuit
21.3. Fan circuit
21.4. Service (a)
21.5. Service (a)
21.6. Service (b)
21.7. Service (b)
22. Tests and adjustments
22.1. Tests and adjustments
22.2. Checking and adjusting the vibration
22.3. Checking and adjusting the vibration
22.4. Checking/adjusting tamping
22.5. Checking/adjusting the scraper belts
22.6. Checking/adjusting the augers
22.7. Checking adjusting the service pump/cylinder functions
22.8. Checking adjusting the time for screed levelling
22.9. Checking/adjusting the hopper wings
22.10. Checking/adjusting the mobile screed
23. Circuit diagrams
23.1. Circuit diagrams
24.
24.1.

Rate this product