Bomag BM 2200-75 Electric Training 00840141

Bomag BM 2200-75 Electric Training 00840141 - Image 2

Bomag BM 2200-75 Electric Training 00840141 - Image 3

Bomag BM 2200-75 Electric Training 00840141 - Image 4

Bomag BM 2200-75 Electric Training 00840141 - Image 5

bomag bm 2200 75 electric training 00840141 2

bomag bm 2200 75 electric training 00840141 3

Bomag BM 2200-75 Electric Training 00840141

$30.00

Type Of Manual: Electric Training
Manual ID: 00840141
Format: PDF
Size: 9.1MB
Number of Pages: 94
Serial Number:
101888011001 and up

Category: Bomag Service Manual PDF

Model List:
- BM 2200-75

1. Table of contents
2. Training of electric system
2.1. Display
2.1.1. Measuring value screens
2.1.2. Service access
2.1.3. Teaching and learning procedures
2.1.4. Configurations
2.1.5. Actuator test
2.1.6. Showing/deleting the fault log
2.1.7. Warnings
2.1.8. Update of display software
2.1.9. Starting up the display without machine identification
2.1.10. Running system functions
2.1.10.1. Belt for milling drum drive
2.1.10.2. Extraction system
2.1.10.3. Height limitation lifting columns
2.1.10.4. Pause function setting
2.1.10.5. Standby function setting
2.2. Procedures for commissioning the machine
2.2.1. Closing the parking brake
2.2.2. Activating the starter
2.2.3. Deactivating monitoring of the belt drive cover
2.2.4. Resetting levelling
2.2.5. Input codes
2.3. Teaching and learning procedures
2.3.1. Lifting column adjustment learning function
2.3.2. Steering setting zero position
2.3.3. Steering learning function
2.3.4. Travel system learning
2.3.5. Adjusting levelling
2.3.6. Zeroing the lifting column heights
2.4. Configurations
2.4.1. Activating/deactivating configurations
2.5. Replacement of components
2.5.1. Introduction
2.5.2. Replacement of the ESX control
2.5.3. Replacement of engine components
2.5.4. Replacing components without an adjustment procedure
2.6. CAN BUS overview
2.7. Levelling control commissioning
2.7.1. Preliminary remarks and safety notes
2.7.2. Control unit for levelling system
2.7.2.1. Buttons and displays
2.7.2.2. Display
2.7.2.3. Navigating through the menus
2.7.3. Preparations for levelling
2.7.3.1. Setting the screen contrast
2.7.3.2. Sensor selection for control circuits left and right
2.7.3.3. Zero balancing
2.7.4. Working with levelling system
2.7.4.1. Setting the nominal value
2.7.4.2. Adjusting actual value equals nominal value
2.7.4.3. Lifting up and cutting in
2.7.5. Adapting the control speed
2.7.6. Adjusting the control window
2.7.6.1. Adjusting the control window equally for all distance sensors
2.7.6.2. Adjusting the rope sensor control window
2.7.6.3. Adjusting the crossslope sensor control window
2.7.7. Changing measurement units
2.7.7.1. Changing rope sensor measurement units
2.7.7.2. Changing crossslope sensor measurement units
2.7.8. Changing the deadband
2.7.9. Changing the work mode
2.7.10. Configuration menu
2.7.10.1. Hydraulic calibration
2.7.10.1.1. Calibrating MIN pulse
2.7.10.1.2. Calibrating MAX pulse
2.7.10.2. Editing the information lines for the activation message
2.7.11. Inspection and troubleshooting

Rate this product