bomag bw 213 dh 4 to bvc with attachment plate single drum roller operating and maintenance instructions 00804461 1

bomag bw 213 dh 4 to bvc with attachment plate single drum roller operating and maintenance instructions 00804461 2

bomag bw 213 dh 4 to bvc with attachment plate single drum roller operating and maintenance instructions 00804461 3

bomag bw 213 dh 4 to bvc with attachment plate single drum roller operating and maintenance instructions 00804461 4

bomag bw 213 dh 4 to bvc with attachment plate single drum roller operating and maintenance instructions 00804461 5

Bomag BW 213 DH-4 to BVC With Attachment Plate Single Drum Roller Operating and Maintenance Instructions 00804461

$20.00

Type Of Manual: Operating and Maintenance Instructions
Manual ID: 00804461
Format: PDF
Size: 4.8MB
Number of Pages: 166
Serial Number:
10158306

Category: Bomag Operator Manual PDF

Model List:
- BW 213 DH-4 Single Drum Roller
- BW 213 PDH-4 Single Drum Roller
- BVC With Attachment Plate Single Drum Roller

1. BW 213 DH4 / PDH4
2. BVC with attachment plates
3. Single drum roller
4. General notes
5. Description of indicators and control elements
6. Display and control elements Variocontrol
7. Description of indicating and control elements Variocontrol
8. Line diagram Automatic (EVIB)
9. Description of line diagram Automatic (EVIB)
10. Line diagram Manual (EVIB)
11. Description of line diagram Manual (EVIB)
12. Bar diagram (EVIB)
13. General notes
14. Tests before taking into operation
15. Starting the engine
16. Starting with jump wires
17. Driving the machine
18. Switching the vibration on and off
19. Operating the parking brake, stopping the machine
20. Shutting the engine down
21. Changing the LCDdisplay
22. Emergency exit
23. Adjusting the seat
24. Operating the hood
25. Towing in case of an engine failure
26. Transport
27. Tests before starting to operate
28. Mounting the attachment plates
29. Taking the attachment plates into service
30. Detaching the attachment plates
31. Variocontrol, selecting the operating mode
32. Measuring pass with Variocontrol
33. Finishing compaction of a track
34. Printing measuring data after completing compaction
35. Teaching distance pulses
36. Amplitude limitation (BVC only)
37. Changing the paper roll in the measuring value printer
38. Changing the printer ribbon in the measuring value printer
39. General notes on maintenance
40. Fuels and lubricants
41. Table of fuels and lubricants
42. Runningin instructions
43. Maintenance chart
44. Check the engine oil level
45. Check, clean the water separator
46. Check the fuel level
47. Check the hydraulic oil level
48. Check the coolant level
49. Checking the dust separator on the oil bath air filter
50. Checking the tire pressure
51. Clean the cooling fins on engine and hydraulic oil cooler
52. Check the oil level in the drive axle
53. Checking the oil level in left/ right wheel hubs
54. Check the oil level in the axle reduction gear
55. Check the oil level in the drum reduction gear
56. Checking the Vario exciter oil level
57. Changing engine oil and oil filter cartridges
58. Change the fuel filter cartridge
59. Draining the sludge from the fuel tank
60. Service the battery
61. Change the fuel prefilter cartridge
62. Checking, replacing the refrigerant compressor Vbelt
63. Service the air conditioning
64. Adjusting the valve clearance
65. Adjusting the control piston play
66. Checking / replacing the ribbed Vbelt
67. Check the engine mounts
68. Change the oil in the drive axle
69. Changing the oil in the wheel hubs
70. Changing the oil in the axle reduction gear
71. Change the oil in the drum reduction gear
72. Vario exciter oil change
73. Change the oil in the exciter shaft housing of the attachment plates
74. Tightening the fastening of the axle to the frame
75. Tightening the wheel nuts
76. Check the ROPS
77. Cleaning the oil bath air filter
78. Changing hydraulic oil and breather filter
79. Changing the hydraulic oil filter
80. Changing the steering oil filter
81. Changing the attachment plate oil filter
82. Change the coolant
83. Replacing the crank case ventilation valve
84. Electronic injector test EMR
85. Service the combustion air filter
86. Adjust the scrapers
87. Adjust the parking brake
88. Change the tires
89. Change the fresh air filter in the cabin
90. Tightening torques
91. Engine conservation
92. General notes
93. Reading out faults BVC/ BTM05
94. Engine
95. Preparations
96. Cabin assembly
97. Final function tests and checks

Rate this product