Bomag BW 226 BVC-5 Single Drum Roller Operating and Maintenance Instructions 00820176

Bomag BW 226 BVC-5 Single Drum Roller Operating and Maintenance Instructions 00820176 - Image 2

Bomag BW 226 BVC-5 Single Drum Roller Operating and Maintenance Instructions 00820176 - Image 3

Bomag BW 226 BVC-5 Single Drum Roller Operating and Maintenance Instructions 00820176 - Image 4

Bomag BW 226 BVC-5 Single Drum Roller Operating and Maintenance Instructions 00820176 - Image 5

bomag bw 226 bvc 5 single drum roller operating and maintenance instructions 00820176 2

bomag bw 226 bvc 5 single drum roller operating and maintenance instructions 00820176 3

Bomag BW 226 BVC-5 Single Drum Roller Operating and Maintenance Instructions 00820176

$20.00

Type Of Manual: Operating and Maintenance Instructions
Manual ID: 00820176
Format: PDF
Size: 4.7MB
Number of Pages: 244
Serial Number:
101586441001 and up

Category: Bomag Operator Manual PDF

Model List:
- BW 226 BVC-5 Single Drum Roller

1. Table of contents
2. Introduction
2.1. Foreword
2.2. Machine type plate and engine type plate
3. Technical data
3.1. Noise and vibration data
3.1.1. Noise data
3.1.2. Vibration data
4. Concerning your safety
4.1. General prerequisites
4.1.1. General
4.1.2. Explanation of signal words used
4.1.3. Personal protective equipment
4.1.4. Intended use
4.1.5. Improper use
4.2. Definition of responsible persons
4.2.1. Operating company
4.2.2. Expert / qualified person
4.2.3. Driver / operator
4.3. Fundamentals for safe operation
4.3.1. Remaining dangers, remaining risks
4.3.2. Regular safety inspections
4.3.3. Modifications and alterations to the machine
4.3.4. Damage, defects, misuse of safety devices
4.3.5. Roll Over Protective Structure (ROPS)
4.4. Handling fuels and lubricants
4.4.1. Preliminary remarks
4.4.2. Safety regulations and environmental protection regulations for handling diesel fuel
4.4.3. Safety regulations and environmental protection regulations for handling oil
4.4.4. Safety regulations and environmental protection regulations for handling hydraulic oil
4.4.5. Safety regulations and environmental protection regulations for handling coolants
4.4.6. Safety regulations and environmental protection regulations for handling battery acid
4.5. Load/transport the machine
4.6. Startup procedure
4.6.1. Prior to starting up
4.6.2. Starting the engine
4.6.3. Starting the engine with jump leads
4.7. Driving the machine, working operation
4.7.1. Persons in the danger area
4.7.2. Driving the machine
4.7.3. Driving on gradients and slopes
4.7.4. Crossslope
4.7.5. Working with vibration
4.7.6. Parking the machine
4.8. Refuelling
4.9. Emergency procedures
4.9.1. Actuating the emergency stop switch
4.9.2. Disconnecting the battery
4.9.3. Towing the machine
4.10. Maintenance work
4.10.1. Preliminary remarks
4.10.2. Work on hydraulic lines
4.10.3. Working on the engine
4.10.4. Maintenance work on electric components and battery
4.10.5. Working on the air conditioning
4.10.6. Working on wheels and tyres
4.10.7. Cleaning work
4.10.8. After maintenance work
4.11. Repair
4.12. Stickers and signage
5. Indicators and control elements
5.1. Drivers stand
5.1.1. Instrument cluster
5.1.2. Operating console
5.1.3. Arm console
5.2. Cabin
5.2.1. Control panel, cabin
5.2.2. Heating / air conditioning
5.2.3. 12 V DIN socket
5.2.4. Monitor for reversing camera
5.2.5. Fire extinguisher
5.3. Engine compartment
5.3.1. Main battery switch
5.4. Outside of machine
5.4.1. Reversing camera
6. Checks prior to start up
6.1. Notes on safety
6.2. Visual inspections and function tests
6.3. Checking the engine oil level
6.4. Checking the fuel level, topping up fuel
6.4.1. Checking the fuel level
6.4.2. Refuelling
6.5. Checking the hydraulic oil level
6.6. Checking the coolant level
6.7. Checking wheels and tyres
7. Operation
7.1. Settingup the work place
7.1.1. Adjusting the drivers seat
7.1.2. Swivelling the drivers seat
7.1.3. Adjust the steering wheel
7.2. Electronic immobilizer
7.3. Starting the engine
7.4. Travel operation
7.4.1. Preliminary remarks and safety notes
7.4.2. Driving the machine
7.4.3. Applying the parking brake
7.4.4. Notes on travel operation
7.5. Working with vibration
7.5.1. Preliminary remarks and safety notes
7.5.2. Vibration in automatic operation
7.5.3. Vibration in manual mode
7.6. Measuring pass with BVC
7.6.1. Line chart (EVIB) Automatic/manual operation
7.7. Parking the machine in secured condition
7.8. Operating the heating / air conditioning system
7.9. ECOSTOP
7.10. Emergency procedures
7.10.1. Actuating the emergency stop switch
7.10.2. Disconnecting the battery
7.10.3. Towing the machine
7.10.4. After towing
8. Loading / transporting the machine
8.1. Prepare for transport
8.2. Loading the machine
8.3. Lashing the machine to the transport vehicle
8.4. Loading by crane
8.5. After transport
9. Maintenance
9.1. Preliminary remarks and safety notes
9.2. Preparations / concluding work
9.2.1. Open and secure the engine hood
9.2.2. Engaging / releasing the articulation lock
9.3. Fuels and lubricants
9.3.1. Engine oil
9.3.2. Fuel
9.3.3. Coolant
9.3.4. Hydraulic oil
9.3.5. Gear oil SAE 75W90
9.3.6. Gear oil SAE 80W140
9.4. List of fuels and lubricants
9.5. Runningin instructions
9.5.1. General
9.5.2. After 250 operating hours
9.5.3. After 500 operating hours
9.5.4. After 1000 operating hours
9.6. Maintenance Table
9.7. Every 250 operating hours
9.7.1. Cleaning the radiator module
9.7.2. Checking, tensioning the Vbelt for the generator system
9.7.3. Checking the oil level in the drive axle
9.7.4. Checking the oil level in the drive axle reduction gear
9.7.5. Checking the oil level in the wheel hubs
9.7.6. Checking the oil level in the exciter housing
9.7.7. Checking the oil level in the drum drive reduction gear
9.7.8. Changing the fresh air filter in the cabin
9.7.9. Check the parking brake
9.8. Every 500 operating hours
9.8.1. Change engine oil and oil filter cartridge
9.8.2. Replacing the fuel filter, bleeding the fuel system
9.8.3. Checking the antifreeze concentration and the condition of the coolant
9.8.4. Checking the hydraulic lines
9.8.5. Servicing the battery, checking the main battery isolation
9.8.6. Servicing the air conditioning system
9.9. Every 1000 operating hours
9.9.1. Checking the ribbed Vbelt
9.9.2. Replacing the air conditioning compressor Vbelts
9.9.3. Checking the engine mounts
9.9.4. Replacing the hydraulic oil filter
9.9.5. Change the oil in the drive axle
9.9.6. Change the oil in the drum drive reduction gear
9.9.7. Changing the oil in the wheel hubs
9.9.8. Change the oil in the exciter housing
9.9.9. Change the oil in the drum drive reduction gear
9.9.10. Retightening the fastening of the axle on the frame
9.9.11. Retightening the wheel nuts
9.9.12. Checking the ROPS
9.9.13. Checking the travel control
9.9.14. Cleaning the circulation air filter for the heating
9.10. Every 2000 operating hours
9.10.1. Adjusting the valve clearance
9.10.2. Changing the hydraulic oil
9.10.3. Changing the coolant
9.11. Every 4000 operating hours
9.11.1. Replace ribbed Vbelt and idler pulley
9.12. As required
9.12.1. Air filter maintenance
9.12.2. Checking, cleaning the water separator
9.12.3. Retightening the padfoot shell
9.12.4. Adjust the scrapers
9.12.5. Filling the windscreen washer tank
9.12.6. Replacing the paper roll in the printer
9.12.7. Replacing the printer ribbon in the printer
9.12.8. Drain the fuel tank sludge
9.12.9. Measures prior to extended shutdown period
10. Troubleshooting
10.1. Preliminary remarks
10.2. Starting the engine with jump leads
10.3. Fuse assignment
10.3.1. Notes on safety
10.3.2. Central electrics
10.3.3. Main fuses
10.3.4. Control console cabin
10.4. Engine malfunctions
11. Disposal
11.1. Final shutdown of machine
12. List of special tools

Rate this product