claas axion 850 800 hexa st v a50 tractors technical system pl 1

claas axion 850 800 hexa st v a50 tractors technical system pl 2

Claas AXION 850-800 HEXA St V (A50) Tractors Technical System PL

$100.00

Brand: Claas
Model: AXION 850-800 HEXA St V (A50) Tractors
Type Of Manual: Technical System
Language: PL
Format: PDF(s)
Size: 145 MB

Category: Claas Technical System PDF

File List:

– 00 1169 191 X.pdf
– 00 1171 521 X.pdf

00 1169 191 X.pdf

Table of Content:
1 AXION 850-830-810-800
2 Table of contents
3 Explanation CCN
3.1 CCN (CLAAS Component Number)
4 CCN (CLAAS Component Number)
5 Introduction
5.1 General instructions
5.2 Scope of instruction
5.3 Safety instructions
6 01 Engine
6.1 0125 Injection system / fuel system
6.2 0130 Lubrication system
6.3 0135 Cooling system
6.4 0140 Exhaust system
6.5 0145 Air intake
6.6 0150 Engine mounted parts
6.7 0155 Engine regulation
6.8 0160 Brake-motor
6.9 0165 Secondary exhaust gas circuit
6.10 0197 Check / Measurement / Setting
7 02 Gears / clutch / propshafts
7.1 0202 Complete components
7.2 0222 Hydraulic shuttle gear
7.3 0230 Mechanical transmission
7.4 0234 Reducer under load
7.5 0240 Rear axle housing
7.6 0242 Differential
7.7 0252 Socket for additional electro-hydraulic drive
7.8 0255 Gear cooling system
7.9 0297 Check / Measurement / Setting
8 03 Chassis
8.1 0325 Driven front steering axle
8.2 0397 Check / Measurement / Setting
9 04 Brakes
9.1 0405 Service brake
9.2 0415 Parking brake
9.3 0420 Trailer pneumatic braking system
9.4 0425 Hydraulic trailer brake
9.5 0497 Check / Measurement / Setting
10 05 Steering
10.1 0505 Steering
10.2 0510 Automatic routing
10.3 0597 Check / Measurement / Setting
11 06 Lifts
11.1 0605 Rear linkage
11.2 0610 Front linkage
11.3 0697 Check / Measurement / Setting
12 08 Drives
12.1 0802 Rear PTO
12.2 0804 Front power take-off shaft
12.3 0897 Check / Measurement / Setting
13 09 Plumbing
13.1 0910 Pumps
13.2 0915 Hydraulic lines
13.3 0920 Valves
13.4 0935 Hydraulic system control/supervision
13.5 0980 Hydraulic wiring diagrams
13.6 0990 Accessories
13.7 0997 Check / Measurement / Setting
14 10 Electrics / electronics
14.1 1005 Power supply
14.2 1010 Electrical unit
14.3 1012 Sensors / modules
14.4 1015 Cable harnesses
14.5 1020 Signal lighting
14.6 1025 Work lighting
14.7 1030 On-board computer / display devices
14.8 1035 Operation / multifunction lever
14.9 1080 Electrical wiring diagrams
14.10 1081 List of plugins
14/11 1085 Networks
14/12 1090 Accessories
14.13 1097 Check / Measurement / Setting
15 12 Cab/driver platform
15.1 1225 Rearview mirrors
15.2 1230 Armchair
15.3 1240 Air conditioning
15.4 1297 Check / Measurement / Setting
16 92 Diagnosis
16.1 Presentation of error codes
16.2 Searching for engine fault codes via SPN F”PVED A055″
16.4 Error Code List
17 Part Location
17.1 Hydraulics
17.2 Electrics

00 1171 521 X.pdf

Table of Content:
1 AXION 850-830-810-800 HEXASHIFT
2 Table of contents
3 Explanation CCN
3.1 CCN (CLAAS Component Number)
4 CCN (CLAAS Component Number)
5 Introduction
5.1 Safety instructions
5.2 General instructions
5.3 Scope of instruction
6 09 Plumbing
6.1 0980 Hydraulic N

4.9/5 - (431 votes)