Claas C540-C450 Folding Lexion (713) Combines Assembly Instruction EN

File List:

00 0290 143 2.pdf
00 0292 437 0.pdf
00 0292 634 0.pdf
00 0292 903 0.pdf
00 0299 557 1.pdf
00 0299 846 1.pdf
00 0300 374 1.pdf
00 0303 568 0.pdf

00 0299 557 1.pdf:

Umbauanleitung
Klappbares Schneidwerk LEXION MONTANA
Einleitung
Besonders zu beachten
Kennzeichnung von Warn- und Gefahrenhinweisen
Bestimmungsgeme Verwendung
Lieferumfang
Umrstsatz 517 653.1
Schneidwerk fr LEXION MONTANA Umbauen
Schneidwerkverriegelung und Hydraulik_x0004_leitungen abbauen
Brcken (1) anschweien
Hydraulikleitungen mit Zubehr anbauen und anschlieen
Schnittwinkel-Verstellung
Schnittwinkel einstellen
Distanztrger anbringen
Fangstcke anbringen
Fangzapfen nach dem Anbau des Schneidwerkes entraegeln
Fangzapfen vor dem Abbau des Schneidwerkes entraegeln
Kabelsatz verlegen und berbrcken
Haken mit Zubehr anbauesser-Antriebsriemen ablegen
Messer-Antriebsriemen auflegen und einstellen
Einzugs-Antriebskette auflegen und einstellen
Weitwinkel-Gelenkwellen (25) links und rechts anbauen
Probelauf vorbereiten und durchfhren
Modification instructions
LEXION MONTANA repliable coupe tab
Introduction
Contents
Important
Identification of prescriptions concerning warnings and dangers
Usage compliant with prior employment regulations
Pices fournies
Jeu de modification 517 653.1
Modification of the coupe tablier for the LEXION MONTANA
Dmontage du verrouillage du tablier de coupe et des conduites hydrauliques
Soudage des pontets_x0011_(1)
Assembly and connection of hydraulic conduits with accessories
Adjustment of the coupe corner
Adjustment of the coupe corner
Pose du support d’cartement
Pose of reception pieces
Dverrouillage du support de rception aprs montage du tablier de coupe
Dverrouillage du de coupe
Pose and short circuit of the cables
Assembly of crochets with accessories
Modification of the intermdiaire_x0011_(24) left and right
Release of the food intake chain
Leave the entrance door for the lames
Pose and direction of the entrance corridor of the lames
Pose and setting of the food intake chain
Montage of the cardan shaft large angle_x0011_(25) _x0011_gauche et right
Preparation and execution of an arthouse brand
Instructions for modification
LEXION MONTANA folding cutterbar
Introduction
Important warning
Warning and danger sign
Specific use
Total supply
Upgrade kit 517 653.1
Modification of the cutterbar for LEXION MONTANA
Removing the cutterbar lock and hydraulic lines
Apply the bridges_x0011_(1) by welding
Assemble and connect the hydraulic hoses with accessories
Adjustment of the cutting angle
Adjust the cutting angle
Apply the spacer sts
Apply the stop pawls
Unlock the locking pins a the cutterbar
Unlock the locking pins before dismantling the cutting platform
Lay and bridge the cable bundle
Mount the hooks with accessories
Modify the layshaft_x0011_(24) to the right and left
Loosen the introduction drive chain
Remove the blade control transmission belt
Fit and adjust the blade control drive belt
Assemble and adjust the introduction drive chain
Fit the wide-angle cardan shafts_x0011_(25) on the left and right
Preparation and execution of the operational test

00 0299 846 1.pdf:

Introduction
Introduction
Table of contents
Table of contents
General Information
Vehicle type approval
Important information
Identification plate / Serial number
Safety rules
Safety rules
Safety locks
Feed rake safety locks
Reel safety lock
Safety decals with pictorials
Specifications
Weights / Dimensions / Safety devices
Additional weights
Prior to operation
Carry out prior to initial operation
Driving lights / Cutterbar cylinder
Driving lights for road use
Changing the driving lights (up to serial no. …)
Changing the driving lights (from serial no. …)
Safety lighting rail on the cutterbar
Removing the transport fixtures
Third cutterbar cylinder
Adjusting the cutterbar floatation springs
Accessory equipment
Additional headlights
Fitting the switches and the additional headlights
Installing the push buttons for switching
Mounting the additional headlights on both sides
Adjusting the additional headlights
Operation
Cutterbar skids
Adjusting the cutterbar skids
Cutting angle adjustment
Adjusting the cutting angle
Mounting the spacer bar
Mounting the coupling brackets
Locking the coupling lug after fitting the cutterbar
Unlocking the coupling lug before removing the cutterbar
Mounting the shaft extension
Mounting the extension to the intermediate drive shaft (LEXION 530 – 510)
Fitting the cutterbar
Tilting the cutterbar from the transport position
Installing and removing the cutterbar
Installing the cutterbar when folded in (cutterbar in the transport position)
Locking the cutterbar at top and bottom on both sides
Connecting the universal coupling
Changing the cutterbar from transport position to working position
Fitting the universal drive shafts LEXION MONTANA (from serial no. 71300231)
Removing standard universal drive shafts
Installing the universal drive shaft for LEXION MONTANA
Changing the cutterbar from working position to transport position
Aligning the cutterbar / removing the cutterbar
Aligning the cutterbar (machines without Auto-Contour)
Removing the cutterbar
Adjustments on the cutterbar
Crop dividers
Outer deflector
Adjusting the dividers
Crop lifters
Removing the knife
Installing the knife
Adjusting the knife height
Aligning the knife clips
Spare knife
Adjusting the reel height
Fine height adjustment of the reel
Reel drive
Reel fore and aft adjustment
Feed auger
Adjusting the clearance to the cutterbar bottom plate
Height adjustment of the feed auger
Adjusting the intake finger position
Safety feature
Cutterbar skids
Malfunction, possible cause and/or remedy
Maintenance
Maintenance schedules and lubricants charts
Maintenance schedule
Lubricants chart
Transmissions
Knife drive transmission
Spring-loaded cylinders / Drive chains / Inductive sensors
Adjusting the spring-loaded cylinders for knife drives
Tensioning the drive chains
Tensioning the reel drive chain
Cleaning the guide rails of the locking cylinder
Aligning the double fingers
Adjusting the reel limit switch
Adjusting the locking pawl at the centre reel guide
Cleaning the spaces of the supporting arm bearings
Cleaning the coupling lug areas
Suggestions for winter storage
Lubrication chart
Lubricants and notes