Claas C900-C600 Mega Medion Do-Vx (701) Combines Operator Manual ES

File List:

00 0290 005 1.pdf

00 0290 005 1.pdf:

1. Introduction
1.1 General instructions
1.1.1 Using the instructions
1.1.2 Validity of the manual
1.1.3 Technical data
1.2 Identification plates and identification numbers
1.2.1 Spare parts and technical issues
1.2.2 Identification plate
3 Security measures
3.1 General instructions
3.1.1 Especially important
3.1.2 General prescriptions for safety and accident prevention
3.1.3 Proper use of the machine
3.1.4 Predictably foolish misuse
3.1.5 Precautionary measures
3.2 General safety warnings
3.2.1 Insert the feed channel safety support
3.2.2 Remove the safety support from the feed channel
3.2.3 Install the cutter bar protection device
3.2.4 Pressurized air and water
3.2.5 Risk of accident due to hydraulic fluid
3.2.6 Prevention against burns
3.2.7 Oil
3.2.8 Prevention against fires and explosions
3.2.9 Pipes, tubes and hoses
3.2.10 Before each start-up
3.2.11 Commissioning of the machine
3.2.12 Road traffic
3.2.13 Park
3.2.14 First aid measures
3.2.15 Decommissioning and waste disposal
3.3 Safety instructions
3.3.1 Warning and danger signs
3.4 Warning symbols
3.4.1 General instructions regarding warning symbols
3.4.2 Drives
3.4.3 Assembled parts/machine casing
4 Technical data
4.1 C900-C300 – TYPE 701/702/703
4.1.1 Eligible machines
4.1.2 Measurements
4.1.3 Weights
4.1.4 Crop feeding
4.1.5 Power supply unit
4.1.6 Mowing device
4.1.7 Safety devices
5 Before first start-up
5.1 General instructions
5.1.1 General warnings
5.1.2 Checklist for first start-up
5.2 Harvest harvest
5.2.1 Dismantle the safety equipment for transporting the reel
5.2.2 Harvest divider
5.2.3 Assemble the crop divider (long/short)
5.2.4 Assemble the crop divider (special)
6 Before each start-up
6.1 General instructions
6.1.1 General warnings
6.1.2 Commissioning checklist
6.2 Power supply unit
6.2.1 Check the adjustment of the scraper profiles
7 Assembling/disassembling the front implement
7.1 General instructions
7.1.1 General warnings
7.2 Assemble the head
7.2.1 Assemble the support legs
7.2.2 Hang front implement
7.2.3 Lock front implement
7.2.4 Assemble cardan shaft
7.2.5 Connect the hydraulic system
7.2.6 Plug in the electrical installation (additional equipment)
7.3 Disassemble the head
7.3.1 Unplug the electrical installation (additional equipment)
7.3.2 Uncouple the hydraulic system
7.3.3 Disassemble cardan shaft
7.3.4 Unlock front implement
7.3.5 Unhook front implement
7.3.6 Remove the support legs
8 Setting in operational mode
8.1 General instructions
8.1.1 General warnings
8.2 Mowing device
8.2.1 Mount crop lifters (optional equipment)
8.2.2 Remove crop lifters (optional equipment)
8.2.3 Adjust skates
9 Operational service
9.1 General instructions
9.1.1 General warnings
9.2 General handling
9.2.1 Before operational service in the field
9.2.2 Control the collection of harvest material
9.3 Harvest harvest
9.3.1 Adjust reel tines
9.3.2 Adjustment of crop dividers
9.4 Power supply unit
9.4.1 Adjust scraper strip
9.4.2 Adjust feed auger position
9.4.3 Adjust feed auger fingers
9.4.4 Mount extension of the auger plate
9.4.5 Remove extension of the auger plate
10 Failures and solutions
10.1 General instructions
10.1.1 General warnings
10.2 General faults and solutions
10.2.1 Harvest material is not collected
10.2.2 The cutting mechanism is not parallel to the bottom
10.2.3 The material flow of the cutting mechanism is not homogeneous
10.2.4 Crop feeding reduced or crop is rolled
10.2.5 The auger stops
10.2.6 Cutting height
10.2.7 Blade problems
10.2.8 The blade stops
10.2.9 Material is wound on a reel
10.2.10 Reel fingers rub against the cutter bar
10.2.11 Reel not parallel to cutter bar
10.2.12 The reel stops
10.2.13 The reel does not turn
10.2.14 Foreign material on the tip of the crop divider
10.3 Hydraulic system
10.3.1 Bleed the reel hydraulic cylinders
10.4 Harvest harvest
10.4.1 Adjust reel height
11 Maintenance
11.1 General instructions
11.1.1 General warnings
11.2 General maintenance warnings
11.2.1 Fixing material
11.2.2 Maintenance work at the end of the harvest
11.2.3 Tightening torques for metric regulation thread
11.2.4 Tightening torques for metric fine thread
11.2.5 Tightening torques for hydraulic screw connections with adjusting ring DIN 3861
11.2.6 Tightening torques for hydraulic screw connections and air conditioning screw connections with conical seal and toroidal seal DIN 3865
11.2.7 Tightening torques for screw connections in plastic parts
11.3 Maintenance table
11.3.1 Maintenance intervals
11.4 Lubricant table
11.4.1 Lubricants
11.5 Gearbox/clutch
11.5.1 Check the oil level in the blade drive gearbox
11.5.2 Add more oil to the blade drive gearbox
11.5.3 Drain oil in the blade drive gearbox
11.6 Drives
11.6.1 Remove the reel drive belt
11.6.2 Install the reel drive belt
11.6.3 Remove the blade drive belt
11.6.4 Install the blade drive belt
11.6.5 Adjust blade drive belt
11.6.6 Tension the feed auger drive chain
11.6.7 Adjust the reel drive chain
11.6.8 Check chain tension
11.7 Mowing device
11.7.1 Change blades
11.7.2 Adjust guide plates
12 Greasing scheme
12.1 General instructions
12.1.1 General warnings
12.2 Grease points
12.2.1 Greasing intervals
12.2.2 Grease points – 10 h left
12.2.3 Grease points – 100 h left
12.2.4 Grease points – 100 h right.
12.2.5 Grease points – 250 h left
Alphabetical index