Claas Corto 165 N S (383) Mower Operator Manual EN

File List:

00 0186 514 9.pdf
00 0294 676 0.pdf
00 2348 408 0.pdf
00 2348 427 0.pdf

00 0294 676 0.pdf:

1 Introduction
Introduction
Validity
2 Table of contents
3 Preface
Of special importance
Identification plate
4 Safety rules
Intended use
Identification of warning and danger signs
General safety and accident prevention instructions
Attached machines
Attached devices
PTO Operation
Hydraulic system
Maintenance
Sound pressure level
Safety decals with pictorials
5 Specifications
CORTO 210 S CORTO 210 N
CORTO 185 S CORTO 185 N
CORTO 165 S CORTO 165 N
Axle loads, minimum ballast and total weight calculation
Calculating the minimum ballast front
Calculating the minimum ballast rear
Calculating the actual front axle load
Calculating the actual total weight
Calculating the actual rear axle load
Tyre carrying capacity
Noise level
6 Assembly
Assembly CORTO 210 S / 210 N / 185 S / 185 N /165 S / 165 N
Fitting the conditioner
VAR. 6066 and 6561
Free-swinging conditioner fitting
VAR. 6066 (CORTO 210 / 185 / 165)
Fitting the tine conditioner
VAR. 6561 (CORTO 210 / 185)
Fitting the angle gearbox
VAR. 6066 and VAR. 6561 (CORTO 210 / 185 / 165)
Fitting cutting blades
7 Prior to operation
Check every time prior to operation
Hitching up
Hitch pin
Pull rope
Adjusting the universal drive shaft
Adapting the length
Fitting the universal drive shaft
Mounting the universal drive shaft
Wide angle equal running linkage
Hydraulics
Prop stand
Fitting the machine
Prior to transportation
Driving on public roads
Lighting brackets for mower units without hydraulic lifting
Lighting brackets for mower units with hydraulic lifting and without conditioner
Lighting brackets for mower units with hydraulic lifting and with conditioner
8 Operation
Operation
Working position
Transport position
Cut height adjustment
Collision safety device
Conditioner
Optional equipment
Skid plate extensions for high cutting C03 0010
Angled, reversible mower blades:
Domed mower blades
Reinforced mower blades
Mower blade holder without stop pin
Hydraulic connection parts for tractors R03 0010
Slip yoke kit M03 0010
High cuttingheight device C03 0040
Infinitely variable cutting height adjustment C03 0050
9 Maintenance
Important maintenance instructions
Hydraulic system
Lubrication
Drive systems
Tensioning the drive belts
Gearbox and gear casing
Conditioner gearbox
Mower blades
Changing the mower blades
Mower blade holders
Cut height adjustment
Conditioner
Setting the conditioner
Fitting/removal of the conditioner tines (VAR. 6561)
Hydraulics
Hydraulic hoses
Hydraulic cylinders
Universal drive shaft
Bolted connections
Fasteners
End of season storage
10 Lubrication chart
Safety rules
Lubricants
Lubrication

00 2348 408 0.pdf:

CEMIS 100
Table of contents
1 Introduction
1.1 General information
1.1.1 Validity of the manual
1.1.2 Information about this Operator’s Manual
1.1.3 Symbols and notes
1.2 Intended use
1.2.1 Intended use
1.2.2 Reasonably foreseeable misuse
2 Safety
2.1 Safety rules
2.1.1 General safety and accident prevention regulations
2.1.2 Interaction between terminal and machine or tractor
2.1.3 Electrocution by electrical system
3 Product description
3.1 Overview and method of operation
3.1.1 Overview of CEMIS 100
3.1.2 Function principle of CEMIS 100
3.2 Identification plates and identification numbers
3.2.1 Spare parts and technical questions
3.2.2 Identification plate of CEMIS 100
4 Operating and display elements
4.1 CEMIS 100
4.1.1 User interface for LINER
4.1.2 User interface for ROLLANT
4.1.3 User interface for UNIWRAP
5 Technical specifications
5.1 CEMIS 100
5.1.1 Specification
6 Operation
6.1 CEMIS 100
6.1.1 Operating the CEMIS 100
6.1.2 Switching CEMIS 100 on
6.1.3 Switching CEMIS 100 off
7 Maintenance
7.1 CEMIS 100
7.1.1 Daily
8 Putting out of operation and disposal
8.1 General information
8.1.1 Removal from service and disposal
9 Technical terms and abbreviations
9.1 Terms and explanations
9.1.1 Technical words
9.1.2 Abbreviations

00 2348 427 0.pdf:

CEMIS 700
Table of contents
1 Introduction
1.1 General information
1.1.1 Validity of the manual
1.1.2 Information about this Operator’s Manual
1.1.3 Symbols and notes
1.2 Intended use
1.2.1 Intended use
1.2.2 Reasonably foreseeable misuse
2 Safety
2.1 Safety rules
2.1.1 General safety and accident prevention regulations
2.1.2 Interaction between terminal and machine or tractor
2.1.3 Electrocution by electrical system
3 Product description
3.1 Overview and method of operation
3.1.1 Overview of CEMIS 700
3.1.2 Function principle of CEMIS 700
3.2 Identification plates and identification numbers
3.2.1 Spare parts and technical questions
3.2.2 Identification plate of CEMIS 700
4 Information on the product
4.1 Software version
5 Operating and display elements
5.1 CEMIS 700
5.1.1 User interface
5.1.2 Terminal program
6 Technical specifications
6.1 CEMIS 700
6.1.1 Specification
7 Operation
7.1 CEMIS 700
7.1.1 Operating the CEMIS 700
7.1.2 Switching CEMIS 700 on
7.1.3 Switching CEMIS 700 off
7.2 Terminal settings
7.2.1 Making settings
Making settings with the rotary button
Making settings with the touch function
7.2.2 Setting the screen lighting
Daytime mode
Nighttime mode
Activating automatic key lighting
7.2.3 Setting the time and date
7.2.4 Displaying diagnosis information
On-board power supply voltage display
Display of CLAAS ISOBUS ECU address and name
7.2.5 Setting the language and display formats
Setting the language
Setting display formats
7.2.6 Setting the volume
7.2.7 Deleting an ISOBUS implement
8 Maintenance
8.1 Maintenance
8.1.1 Daily
9 Putting out of operation and disposal
9.1 General information
9.1.1 Removal from service and disposal
10 Technical terms and abbreviations
10.1 Terms and explanations
10.1.1 Technical words
10.1.2 Abbreviations