Claas Corto 270 F (345) Mower Operator Manual EN

File List:

00 0294 183 9.pdf
00 2348 408 0.pdf
00 2348 427 0.pdf

00 0294 183 9.pdf:

1 Introduction
Introduction
Validity
2 Contents
3 Preface
Of special importance
Identification plate
Intended use
Avoidable incorrect applications
De-commissioning and disposal
Identification of warning and danger signs
General safety regulations and safety precautions
Attached machines
Trailed machines
PTO operation
Hydraulic system
Maintenance
Noise pressure level
Safety decals with pictorials
5 Specifications
Specifications
Axle loads, minimum ballast and total weight calculation
Sound pressure level of drum mower units CORTO 290 F / 290 FN / 270 F / 270 FN / 250 F / 210 F
6 Assembly
Mounting
Mounting compressing rake
Fitting cutters
7 Prior to operation
Check every time prior to operation
Hitching up
Three-point hitching with Accord quick coupler
Three-point fitting without quick coupler:
Adjusting the top link
Mounting the universal drive shaft
Adjusting the universal drive shaft
Mounting the universal drive shaft
Changing the direction of rotation
Weight relief
Suspension spring for ground friction:
Removing/parking the machine
Prior to transportation
Driving on public roads
Identification of the machine for road traffic
Lighting brackets for light carrier (VAR. 5382)
8 Operation
Operation
Working position
Transport position
Adjusting cut height
Adjusting the cutting height for uneven terrain
Headstock interlock
Adjusting the swath discs
Attachment band
Attachments
Difficult operating conditions
Recommendations for environmental protection
Optional equipment
Skid plate extensions for high cutting (C03 0010)
High cuttingheight device C03 0040
Continuous cut height adjustment (C03 0050)
Angled reversible mower blades
Domed mower blades
Reinforced mower blades
Cutter holders without stop pins
Extra swath discs
Swath device (CORTO 250 F)
Swath device (CORTO 210 F)
Slip yoke kit (M03 0010)
Offset fitting (R03 0070)
Conversion kit for large front tyres
9 Maintenance
Important maintenance instructions
Hydraulic system
Lubrication
Protective devices (guard frames)
Drive systems
Tensioning the drive belts
Drive mower drums:
Replacing the V-belts
Gear casing
Oil filling capacity:
Checking the oil level:
Oil change:
Draining oil:
Main gearbox
Oil filling capacity: 0.80 Litre
Changing the gearbox oil:
Cut height adjustment
Mower blades
Replacing mower blades
Mower blade holders
Universal drive shaft
General information for universal drive shafts
Maintaining the plate clutch
Swath device (CORTO 290 F / 290 FN / 270 F / 270 FN)
CORTO 250 F
CORTO 210 F
Fasteners
Bolted connections
End of season storage
10 Lubrication chart
Safety rules
Lubricants
Lubrication

00 2348 408 0.pdf:

CEMIS 100
Table of contents
1 Introduction
1.1 General information
1.1.1 Validity of the manual
1.1.2 Information about this Operator’s Manual
1.1.3 Symbols and notes
1.2 Intended use
1.2.1 Intended use
1.2.2 Reasonably foreseeable misuse
2 Safety
2.1 Safety rules
2.1.1 General safety and accident prevention regulations
2.1.2 Interaction between terminal and machine or tractor
2.1.3 Electrocution by electrical system
3 Product description
3.1 Overview and method of operation
3.1.1 Overview of CEMIS 100
3.1.2 Function principle of CEMIS 100
3.2 Identification plates and identification numbers
3.2.1 Spare parts and technical questions
3.2.2 Identification plate of CEMIS 100
4 Operating and display elements
4.1 CEMIS 100
4.1.1 User interface for LINER
4.1.2 User interface for ROLLANT
4.1.3 User interface for UNIWRAP
5 Technical specifications
5.1 CEMIS 100
5.1.1 Specification
6 Operation
6.1 CEMIS 100
6.1.1 Operating the CEMIS 100
6.1.2 Switching CEMIS 100 on
6.1.3 Switching CEMIS 100 off
7 Maintenance
7.1 CEMIS 100
7.1.1 Daily
8 Putting out of operation and disposal
8.1 General information
8.1.1 Removal from service and disposal
9 Technical terms and abbreviations
9.1 Terms and explanations
9.1.1 Technical words
9.1.2 Abbreviations

00 2348 427 0.pdf:

CEMIS 700
Table of contents
1 Introduction
1.1 General information
1.1.1 Validity of the manual
1.1.2 Information about this Operator’s Manual
1.1.3 Symbols and notes
1.2 Intended use
1.2.1 Intended use
1.2.2 Reasonably foreseeable misuse
2 Safety
2.1 Safety rules
2.1.1 General safety and accident prevention regulations
2.1.2 Interaction between terminal and machine or tractor
2.1.3 Electrocution by electrical system
3 Product description
3.1 Overview and method of operation
3.1.1 Overview of CEMIS 700
3.1.2 Function principle of CEMIS 700
3.2 Identification plates and identification numbers
3.2.1 Spare parts and technical questions
3.2.2 Identification plate of CEMIS 700
4 Information on the product
4.1 Software version
5 Operating and display elements
5.1 CEMIS 700
5.1.1 User interface
5.1.2 Terminal program
6 Technical specifications
6.1 CEMIS 700
6.1.1 Specification
7 Operation
7.1 CEMIS 700
7.1.1 Operating the CEMIS 700
7.1.2 Switching CEMIS 700 on
7.1.3 Switching CEMIS 700 off
7.2 Terminal settings
7.2.1 Making settings
Making settings with the rotary button
Making settings with the touch function
7.2.2 Setting the screen lighting
Daytime mode
Nighttime mode
Activating automatic key lighting
7.2.3 Setting the time and date
7.2.4 Displaying diagnosis information
On-board power supply voltage display
Display of CLAAS ISOBUS ECU address and name
7.2.5 Setting the language and display formats
Setting the language
Setting display formats
7.2.6 Setting the volume
7.2.7 Deleting an ISOBUS implement
8 Maintenance
8.1 Maintenance
8.1.1 Daily
9 Putting out of operation and disposal
9.1 General information
9.1.1 Removal from service and disposal
10 Technical terms and abbreviations
10.1 Terms and explanations
10.1.1 Technical words
10.1.2 Abbreviations