Claas Disco 3050 C (621) Mower Operator Manual EN

File List:

00 0293 857 6.pdf
00 1329 399 0.pdf
00 2348 408 0.pdf
00 2348 427 0.pdf

00 0293 857 6.pdf:

1 Introduction
Introduction
VALIDITY
2 Table of contents
3 Preface
Of special importance
Identification plate
4 Safety Rules
Identification of warning and danger signs
Designated use
Avoidable incorrect applications
General safety and accident prevention regulations
Attached machines
Trailed machines
PTO operation
Hydraulic system
Maintenance
Sound pressure level
De-commissioning and disposal
Safety decals with pictorials
5 Specifications
Specifications
Axial loading, minimum ballast and total weight calculation
Noise pressure level of the disc mowers DISCO 3450 / 3050 / 3050 C / 2650 / 2650 C
6 Prior to operation
Loading / unloading the machine DISCO 3450 / 3050 / 3050 C / 2650 / 2650 C
Check and observe the following before putting into operation!
Attachment to the tractor
Adjusting the hitch
Adjust universal drive shaft
Fitting the universal drive shaft
Universal drive shaft – conditioner
Hydraulics
Fitting the machine
Prior to transportation
Driving on public roads
Identification of the machine for road traffic
7 Operation
Operation
Working position
Safety devices
Transport position
Setting the cutting height
Collision protection
Recommendations for environmental protection
Suspension springs
Swath device Right hand swath disc
Left hand swath disc (Optional equipment DISCO 2650 Plus / 2650)
Left hand swath disc (Optional equipment DISCO 3050 Plus / 3050)
Conditioner DISCO 3050 C / 2650 C
Swath plates DISCO 3050 C / 2650 C
Wide distribution hood (Optional equipment DISCO 3050 C Plus / 2650 C Plus)
Additional equipment
High cutting runners B03 0020
Additional runners C03 0030
Collision protection and safety frame S03 0070
Left hand swath disc G03 0020
Left hand swath plate G03 0030
Changeover kit for PTO speed 1000 rpm P09 0010
Wide distribution hood G03 0010
Slip yoke kit M03 0010
Slip yoke kit M03 0020
Hydraulic connecting parts for tractor R03/ 0010
Lighting adapter (USA, R03/0500)
8 Maintenance
Important maintenance instructions
Hydraulic system
Energy accumulators
Lubrication
Safety device (safety frame)
Drive systems
Tensioning the drive belts
Conditioner gearbox
Mower head
Knife sections
Knife section box
Changing the cutting knives
Blade replacement DISCO 3050 / 2650
Mower discs
Replacing cutting discs
Mower head suspension
Conditioner tines
Fitting/removing tines
Universal drive shaft
Hydraulic system
Hydraulic hose connections
Hydraulic cylinders
Connecting elements
Screw connections
Cleaning and care
Winter storage
Malfunctions
9 Lubrication chart
Safety rules
Lubricants
Lubrication
0501.pdf
5 Specifications
Specifications
Axial loading, minimum ballast and total weight calculation
Noise pressure level of the disc mowers DISCO 3450 / 3050 / 3050 C / 2650 / 2650 C

00 2348 408 0.pdf:

CEMIS 100
Table of contents
1 Introduction
1.1 General information
1.1.1 Validity of the manual
1.1.2 Information about this Operator’s Manual
1.1.3 Symbols and notes
1.2 Intended use
1.2.1 Intended use
1.2.2 Reasonably foreseeable misuse
2 Safety
2.1 Safety rules
2.1.1 General safety and accident prevention regulations
2.1.2 Interaction between terminal and machine or tractor
2.1.3 Electrocution by electrical system
3 Product description
3.1 Overview and method of operation
3.1.1 Overview of CEMIS 100
3.1.2 Function principle of CEMIS 100
3.2 Identification plates and identification numbers
3.2.1 Spare parts and technical questions
3.2.2 Identification plate of CEMIS 100
4 Operating and display elements
4.1 CEMIS 100
4.1.1 User interface for LINER
4.1.2 User interface for ROLLANT
4.1.3 User interface for UNIWRAP
5 Technical specifications
5.1 CEMIS 100
5.1.1 Specification
6 Operation
6.1 CEMIS 100
6.1.1 Operating the CEMIS 100
6.1.2 Switching CEMIS 100 on
6.1.3 Switching CEMIS 100 off
7 Maintenance
7.1 CEMIS 100
7.1.1 Daily
8 Putting out of operation and disposal
8.1 General information
8.1.1 Removal from service and disposal
9 Technical terms and abbreviations
9.1 Terms and explanations
9.1.1 Technical words
9.1.2 Abbreviations

00 2348 427 0.pdf:

CEMIS 700
Table of contents
1 Introduction
1.1 General information
1.1.1 Validity of the manual
1.1.2 Information about this Operator’s Manual
1.1.3 Symbols and notes
1.2 Intended use
1.2.1 Intended use
1.2.2 Reasonably foreseeable misuse
2 Safety
2.1 Safety rules
2.1.1 General safety and accident prevention regulations
2.1.2 Interaction between terminal and machine or tractor
2.1.3 Electrocution by electrical system
3 Product description
3.1 Overview and method of operation
3.1.1 Overview of CEMIS 700
3.1.2 Function principle of CEMIS 700
3.2 Identification plates and identification numbers
3.2.1 Spare parts and technical questions
3.2.2 Identification plate of CEMIS 700
4 Information on the product
4.1 Software version
5 Operating and display elements
5.1 CEMIS 700
5.1.1 User interface
5.1.2 Terminal program
6 Technical specifications
6.1 CEMIS 700
6.1.1 Specification
7 Operation
7.1 CEMIS 700
7.1.1 Operating the CEMIS 700
7.1.2 Switching CEMIS 700 on
7.1.3 Switching CEMIS 700 off
7.2 Terminal settings
7.2.1 Making settings
Making settings with the rotary button
Making settings with the touch function
7.2.2 Setting the screen lighting
Daytime mode
Nighttime mode
Activating automatic key lighting
7.2.3 Setting the time and date
7.2.4 Displaying diagnosis information
On-board power supply voltage display
Display of CLAAS ISOBUS ECU address and name
7.2.5 Setting the language and display formats
Setting the language
Setting display formats
7.2.6 Setting the volume
7.2.7 Deleting an ISOBUS implement
8 Maintenance
8.1 Maintenance
8.1.1 Daily
9 Putting out of operation and disposal
9.1 General information
9.1.1 Removal from service and disposal
10 Technical terms and abbreviations
10.1 Terms and explanations
10.1.1 Technical words
10.1.2 Abbreviations