Claas Disco 3150 C (F79) Mower Operator Manual EN

File List:

00 0300 512 1.pdf
00 1329 399 0.pdf
00 2348 408 0.pdf
00 2348 427 0.pdf

00 0300 512 1.pdf:

DISCO 3150 CDISCO 2750 CDISCO 2750 RC
Table of contents
1 Introduction
1.1 Notes on the manual
1.1.1 Validity of manual
1.1.2 Information about this Operator’s Manual
1.1.3 Symbols and notices
1.1.4 Optional equipment
1.1.5 Qualified specialist workshop
1.1.6 Notes on warranty
1.1.7 Spare parts and technical questions
1.2 Intended use
1.2.1 Intended use
1.2.2 Reasonably foreseeable misuse
2 Safety
2.1 Identifying warnings
2.1.1 Hazard signs
2.1.2 Signal word
2.2 Safety rules
2.2.1 Importance of Operator’s Manual
2.2.2 Observing safety decals and warnings
2.2.3 Requirements for all persons working with the machine
2.2.4 Children in danger
2.2.5 Hazard areas
2.2.6 Staying between the tractor and the machine
2.2.7 Hitching the tractor to the machine
2.2.8 Risk of injury from rotating shafts
2.2.9 Structural changes
2.2.10 Optional equipment and spare parts
2.2.11 Control of the machine while it is running
2.2.12 Operation only after proper putting into operation
2.2.13 Technical condition
2.2.14 Danger due to damage to the machine
2.2.15 Respecting technical limit values
2.2.16 Danger from machine parts running on
2.2.17 Keeping protective equipment functional
2.2.18 Personal protective equipment
2.2.19 Wearing suitable clothing
2.2.20 Removing dirt and loose objects
2.2.21 Preparing the machine for road travel
2.2.22 Hazards when driving on the road and in the field
2.2.23 Parking the machine safely
2.2.24 Unsupervised parking
2.2.25 Unsuitable operating materials
2.2.26 Safe handling of operating and auxiliary materials
2.2.27 Environmental protection and disposal
2.2.28 Lethal electrocution from overhead lines
2.2.29 Behaviour in case of voltage flash-over from overhead lines and when lightning strikes
2.2.30 Noise may cause health damage
2.2.31 Liquids under pressure
2.2.32 Hot surfaces
2.2.33 Only carry out work on the machine when it is shut down
2.2.34 Maintenance operations and repairs
2.2.35 Raised machine parts and loads
2.2.36 Danger from welding work
2.3 Safety marking
2.3.1 Layout of safety decals
2.3.2 Safety decals on the machine
3 Machine description
3.1 Overview and method of operation
3.1.1 Machine overview
3.1.2 Overview of cutting disc direction of rotation
3.1.3 Function of DISCO 3150 C / DISCO 2750 C
3.1.4 Function of DISCO 2750 RC
3.2 Optional equipment
3.2.1 High-cut skids*
3.2.2 Double high-cut skids*
3.2.3 Wear skids*
3.2.4 Slip-on yoke for 8-piece universal drive shaft*
3.2.5 Slip-on yoke for 21-piece universal drive shaft*
3.2.6 1-part hydraulic connectors*
3.2.7 Crop spreader*
3.2.8 Parking device*
3.2.9 Warning panel with lights*
3.2.10 Lighting adapter for USA*
3.3 Identification plates and vehicle identification number
3.3.1 Machine identification plate
3.4 Information on the machine
3.4.1 Stickers on the machine
4 Operating and control elements
4.1 Controls
4.1.1 Machine
4.2 Display elements
4.2.1 Frame
4.2.2 Crop spreader*
5 Technical specifications
5.1 DISCO 3150 C
5.1.1 Dimensions
5.1.2 Weights
5.1.3 Requirements on the tractor
5.1.4 Version
5.1.5 Sound pressure level
5.1.6 Lubricants
5.2 DISCO 2750 C / 2750 RC
5.2.1 Dimensions
5.2.2 Weights
5.2.3 Requirements on the tractor
5.2.4 Version
5.2.5 Sound pressure level
5.2.6 Lubricants
6 Machine preparation
6.1 Switching off and securing the machine
6.1.1 Switch off and secure the tractor and machine
6.1.2 Securing the raised machine
6.2 Access to workplace and maintenance positions
6.2.1 Opening and closing the front safety guard
6.3 Adapting the tractor
6.3.1 Checking the ballasting of the tractor
Calculating the minimum front ballast
Calculating the minimum rear ballast
Calculating the actual front axle load
Calculating the actual total weight
Calculating the actual rear axle load
Calculation table
6.4 Adapting the machine
6.4.1 Universal drive shaft – checking the length
6.4.2 Adapting the length of the universal drive shaft
6.4.3 Fitting the PTO shaft to the machine
6.4.4 Adapting the lower link pin
6.4.5 Adapting the lower link category
6.4.6 Adapting the upper link category
6.5 Hitching the machine
6.5.1 Fitting the lower link
6.5.2 Fitting the upper link
6.5.3 Installing the universal drive shaft
6.5.4 Connecting the hydraulic hose line
6.5.5 Connecting the lighting cable
6.5.6 Release the mower unit from the parking device*
6.5.7 Raising the jack stand
6.5.8 Laying the pull rope
6.5.9 Remove the mower unit from the parking device*.
6.6 Unhitching the machine
6.6.1 Parking the machine
6.6.2 Lowering the stand
6.6.3 Disconnecting the lighting cable
6.6.4 Storing the pull rope
6.6.5 Removing the universal drive shaft
6.6.6 Unhooking the upper link
6.6.7 Unhooking the lower link
6.6.8 Disconnecting the hydraulic hose line
6.7 Uncoupling the machine from the parking device*
6.7.1 Securing the mower unit in the parking device*
6.7.2 Disconnecting the lighting cable
6.7.3 Storing the pull rope
6.7.4 Removing the universal drive shaft
6.7.5 Unhooking the upper link
6.7.6 Unhooking the lower link
6.7.7 Disconnecting the hydraulic hose line
6.8 Prepare road travel
6.8.1 Swinging to transport position
6.8.2 Marking the machine for road travel
6.8.3 Checking before starting road travel
6.9 Preparing the working position
6.9.1 Swinging to working position
6.10 Loading the machine
6.10.1 Loading the machine
7 Operation
7.1 Driving on the road
7.1.1 Driving on public roads
7.2 Fieldwork settings
7.2.1 Adjusting the attachable frame
7.2.2 Adjusting the mower head load relief
Basic adjustment of tension springs
Adjusting the load relief
7.2.3 Adjusting the cutting height
7.2.4 Adjusting the tine conditioner
7.2.5 Adjusting the roller conditioner
7.2.6 Putting the roller conditioner out of operation
7.2.7 Adjusting the swath width
7.2.8 Adjusting the crop spreader*
7.2.9 Retensioning the collision protection
7.3 Fieldwork
7.3.1 To be observed during fieldwork
7.3.2 Machine use
7.3.3 Adapting the PTO speed
7.3.4 Adapting the PTO speed
7.3.5 Mowing methods
7.3.6 Lifting the machine to the headland position
7.3.7 Engaging collision protection
7.3.8 Instructions for mowing
7.3.9 Difficult conditions of use
7.3.10 Recommendation for environmental protection
8 Faults and remedies
8.1 Overview of faults
8.1.1 Problems on the machine
8.2 Universal drive shafts
8.2.1 Conditioner no longer turns
8.3 Electric system
8.3.1 Defective incandescent lamps
8.4 Hydraulic system
8.4.1 Mower head drop rate is too low
8.5 Mower unit
8.5.1 The cutting disc no longer turns
9 Maintenance
9.1 Service interval overview
9.1.1 Before the harvest
9.1.2 After the first 50 operating hours
9.1.3 Every 8 operating hours
9.1.4 Every 20 operating hours
9.1.5 Every 100 operating hours
9.1.6 Every 250 operating hours
9.1.7 Every 500 operating hours or annually
9.1.8 Every 5 years
9.1.9 After the harvest
9.2 Drive belt
9.2.1 Checking the drive belt
9.3 Gearbox
9.3.1 Check the gearboxes for leak-tightness
9.3.2 Check the oil level of the angle drive
9.3.3 Checking the oil level in the conditioner gearbox
9.3.4 Changing the oil in the angle drive
9.3.5 Changing the oil in the conditioner gearbox
9.4 Clutch
9.4.1 Cleaning the free-wheel clutch on the universal drive shaft
9.5 Universal drive shafts
9.5.1 Service the universal drive shaft
9.6 Hydraulic system
9.6.1 Check the hydraulic hose lines
9.6.2 Installing and removing hydraulic cylinders
9.7 Mower unit
9.7.1 Checking the mower head oil level
9.7.2 Changing the mower head oil
Draining oil
Topping up oil
9.7.3 Check the mower knives
9.7.4 Replacing the mower knives
9.7.5 Check the mower knife holder
9.7.6 Clean the drain opening of the feed drum
9.7.7 Check the wear bars of the feed drum
9.7.8 Check the cover plate on the feed drum
9.7.9 Check the sealing washer of the feed drum
9.7.10 Check the cutting discs
9.7.11 Replacing the cutting discs
9.7.12 Adjusting the anti-wrap guard
9.7.13 Checking the connection pieces
9.8 Crop processing unit
9.8.1 Checking the tines
9.8.2 Adjusting the roller conditioner
Adjusting the tension spring
Adjusting synchronous running
Adjusting the roller clearance
9.9 Assembly parts and bodywork
9.9.1 Clean machine
9.9.2 Preserve the machine
9.9.3 Checking the fittings
9.9.4 Checking the safety guard holder
9.10 Lubrication chart
9.10.1 Grease points to be greased every 20 operating hours
9.10.2 Grease points to be greased every 100 operating hours
9.10.3 Grease points to be greased every 250 operating hours
10 Placing out of operation and disposal
10.1 General information
10.1.1 Placing out of operation and disposal
11 EC declaration of conformity
11.1 DISCO 3150 C / 2750 C / 2750 RC
11.1.1 EC Declaration of Conformity
12 Technical terms and abbreviations
12.1 Terms and explanations
12.1.1 Technical terms
12.1.2 Abbreviations

00 2348 408 0.pdf:

CEMIS 100
Table of contents
1 Introduction
1.1 General information
1.1.1 Validity of the manual
1.1.2 Information about this Operator’s Manual
1.1.3 Symbols and notes
1.2 Intended use
1.2.1 Intended use
1.2.2 Reasonably foreseeable misuse
2 Safety
2.1 Safety rules
2.1.1 General safety and accident prevention regulations
2.1.2 Interaction between terminal and machine or tractor
2.1.3 Electrocution by electrical system
3 Product description
3.1 Overview and method of operation
3.1.1 Overview of CEMIS 100
3.1.2 Function principle of CEMIS 100
3.2 Identification plates and identification numbers
3.2.1 Spare parts and technical questions
3.2.2 Identification plate of CEMIS 100
4 Operating and display elements
4.1 CEMIS 100
4.1.1 User interface for LINER
4.1.2 User interface for ROLLANT
4.1.3 User interface for UNIWRAP
5 Technical specifications
5.1 CEMIS 100
5.1.1 Specification
6 Operation
6.1 CEMIS 100
6.1.1 Operating the CEMIS 100
6.1.2 Switching CEMIS 100 on
6.1.3 Switching CEMIS 100 off
7 Maintenance
7.1 CEMIS 100
7.1.1 Daily
8 Putting out of operation and disposal
8.1 General information
8.1.1 Removal from service and disposal
9 Technical terms and abbreviations
9.1 Terms and explanations
9.1.1 Technical words
9.1.2 Abbreviations

00 2348 427 0.pdf:

CEMIS 700
Table of contents
1 Introduction
1.1 General information
1.1.1 Validity of the manual
1.1.2 Information about this Operator’s Manual
1.1.3 Symbols and notes
1.2 Intended use
1.2.1 Intended use
1.2.2 Reasonably foreseeable misuse
2 Safety
2.1 Safety rules
2.1.1 General safety and accident prevention regulations
2.1.2 Interaction between terminal and machine or tractor
2.1.3 Electrocution by electrical system
3 Product description
3.1 Overview and method of operation
3.1.1 Overview of CEMIS 700
3.1.2 Function principle of CEMIS 700
3.2 Identification plates and identification numbers
3.2.1 Spare parts and technical questions
3.2.2 Identification plate of CEMIS 700
4 Information on the product
4.1 Software version
5 Operating and display elements
5.1 CEMIS 700
5.1.1 User interface
5.1.2 Terminal program
6 Technical specifications
6.1 CEMIS 700
6.1.1 Specification
7 Operation
7.1 CEMIS 700
7.1.1 Operating the CEMIS 700
7.1.2 Switching CEMIS 700 on
7.1.3 Switching CEMIS 700 off
7.2 Terminal settings
7.2.1 Making settings
Making settings with the rotary button
Making settings with the touch function
7.2.2 Setting the screen lighting
Daytime mode
Nighttime mode
Activating automatic key lighting
7.2.3 Setting the time and date
7.2.4 Displaying diagnosis information
On-board power supply voltage display
Display of CLAAS ISOBUS ECU address and name
7.2.5 Setting the language and display formats
Setting the language
Setting display formats
7.2.6 Setting the volume
7.2.7 Deleting an ISOBUS implement
8 Maintenance
8.1 Maintenance
8.1.1 Daily
9 Putting out of operation and disposal
9.1 General information
9.1.1 Removal from service and disposal
10 Technical terms and abbreviations
10.1 Terms and explanations
10.1.1 Technical words
10.1.2 Abbreviations