Claas Dominator 108 Sl Vx (094) Combines Assembly Instruction EN

File List:

00 0186 918 0.pdf
00 0188 972 1.pdf
00 0290 143 2.pdf
00 0292 437 0.pdf
00 0295 105 1.pdf
00 0297 657 1.pdf
00 0297 727 0.pdf
00 0299 185 0.pdf
00 0299 404 0.pdf
00 0300 374 1.pdf

00 0188 972 1.pdf:

Anbauanleitung
Sonnenblumen-Vorsatz
Instructions
Besons on the beach
Kennzeichnung von Warn- und Gefahrenhinweisen
Bestimmungsgeme Verwendung
Lieferumfang
Sonnenblumen-Vorsatz anbauen
Sicherheitssttzen
Schrgfrderer-Sicherheitssttze
Haspel-Gitterbleche einbauen
Steuerstern ausbauen (Haspelantrieb links)
Haspel-Zinkenabdeckung anbauen
Haspel-Antriebskette auflegen und spannen
Halmteiler und Schiffchen anbauen
Fitting instructions
Sunflower attachment
Introduction
Table of contents
Important information
Identification of warning and danger signs
Correct use
Shipping package
Fitting the sunflower attachment
Safety locks
Feed rake sng plates
Removing the control star (LH reel drive)
Attaching the reel tine cover
Fitting and tightening the reel drive chain
Fitting the divider and seed pan
Installation instructions
Sunflower front accessory
Introduction
Contents
Important
Marking of warnings and dangers
Use in accordance with instructions
Parts supplied
Assembly of front equipment for sunflower
Safety crutches
Conveyor safety stand
Installation of the perforated reel plates
Removing the control ring (left reel drive)
Installing the reel finger cover
Installing and tensioning the reel drive chain
Installing the divider and shuttle

00 0299 185 0.pdf:

Anbauanleitung
Hydraulic Reversierantrieb
1 Instructions
Instructions
2 Inhalt
3 Allgemeine Hinweise_x0011_
Besons on the beach
Kennzeichnung von Warn- und Gefahrenhinweisen
Bestimmungsgeme Verwendung
ferumf Contact details 517 344.2 for MEDION 340 and MEGA 208
Contact details 517 343.2 for MEDION 330/310 and MEGA 204
Hydraulic Reversierantrieb anbauen
Anbau vorbereiten
Electrical Reversierantrieb abbauen
Cables for electrical reverse power sources
Schneidwerk-Antriebsriemen_x0011_(A) ablegen
Vorgelegewelle ausbauen
New Vorgelegewelle_x0011_(1) einbauen
Hydraulic Reversierantrieb vormontieren
Hydraulic Reversierantrieb anbauen
Hydraulic cylinder (2) included
4/2-Wegeventil (3) anbauen
Hydraulic switch (5) and (7) connections
Ventilblock ausbauen
Cables (21) anbauen
Schneidwerk-Antriebsriemen auflegen und einstellen
Hydraulic stand controls
Probelauf vorbereiten und durchfhren
Fitting Instructions
Hydraulic Reverse Drive
1 Introduction
Introduction
2 Contents
3 General information
Important
Identification of warnind danger signs
Correct use
4 Shipping Package
Shipping Package
Supplementary kit 517 344.2 for MEDION 340 and MEGA 208
Supplementary kit 517 343.2 for MEDION 330/310 and MEGA 204
5 Fitting
Installing the hydraulic reverse drive
Preparing the fitting
Dismounting the electrical reverse drive
Dismounting wiring loom for electrical reverse drive
Removing the cutterbar drive belt_x0011_(A)
Removing intermediate drive shaft
Installing the new intermediate drive shaft_x0011_(1)
Pre-assembly of the hydraulic reverse drive
Installing the hydraulic reverse drive
Adjusting hydraulic cylinder (2)
Installing 4/2 way valve (3)
Connecting hydraulic oil hoses (5) and (7)
Removing valve block
Installing wiring loom (21)
Putting on and adjusting the cutterbar drive belt
Checking hydraulic oil filling level
Preparing and performing the test run
Installation instructions
Hydraulic reversing control
1 Introduction
Introduction
2 Content
3 General tips
Important
Identification of warning and hazard requirements
Use in accordance with intended use
4 pieces supplied
Parts supplied
Additional equipment set 517 344.2 for MEDION 340 and MEGA 208
Additional equipment set 517 343.2 for MEDION 330/310 and MEGA 204
5 Assembly
Installing the hydraulic reversing control
Preparing for assembly
Disassembly of the electric reversing control
Dismantling the cable set for the electric reversing control
Removing the cutting deck drive belt_x0011_(A)
Intermediate shaft disassembly
Fitting a new intermediate shaft_x0011_(1)
Pre-assembly of hydraulic reversing control
Installing the hydraulic reversing control
Adjusting the hydraulic cylinder (2)
Mounting the 4/2 distributor (3)
Connecting the hydraulic oil hoses (5)_x0011_and (7)
Disassembly of the valve block
Installing the cable set (21)
Installing and adjusting the cutting deck drive belt
Check the hydraulic oil level
Preparing and executing a test run

00 0299 404 0.pdf:

Growing instructions
3. Cutting cylinder
1 Introduction
Introduction
2 Contents
Contents
3 General _x0004_Notes
Of particular note
Labeling of warnings and danger notices
Intended Use
4 scope of delivery
scope of delivery
Retrofit kit 633 836.0
5 Cultivation
Install the third cutting cylinder
Prepare for cultivation
Install cutting unit cylinder
Prepare and carry out a test run
Fitting instructions
3. Cutter bar cylinder
1 Introduction
Introduction
2 contents
Contents
3 General _x0004_information
Important
Identition of warnings and danger signs
Correct use
4 Shipping Package
Shipp Supplementary kit 633 836.0
5 Installation
Installing the third cutterbar cylinder
Preparing the installation
Installing the cutterbar cylinder
Preparing and performing the test run
Notice of assembly
3. Vrin de tablier de coupe
1 Introduction
Introduction
2 Contenu
3 Conseils_x0004_gnraux
Important
Identification of the prescriptions concerning the avertissements and the dangers
Utilization conforme l’emploi prvu
4 pieces fournies
Pieces fournies
Additional equipment kit 633 836.0
5 assembly
Montage du troisime vrin de tablier de coupe
Preparation for assembly
Montage du vrin de table de coupe