Claas Lexion 460-440 (544) Combines Operator Manual ES

File List:

00 0298 433 0.pdf
00 0298 597 0.pdf

00 0298 433 0.pdf:

Introduction
Introduction
General indications
Circulation on public roads
Important note
Nameplate / Serial_x0011_number
Machine factory plate
Chassis number
CATERPILLAR C9 engine number
Engine number CATERPILLAR 3126 B
Factory plate – straw chopper
Cabin serial number
Security measures
Security measures
Security support
Extinguisher
Battery disconnect switch
Place the shims
Safety stickers with graphic danger symbols
Technical data
CLAAS LEXION 460 / 450 / 440
CLAAS LEXION 460 / 450 / 440
CLAAS LEXION 460 / 450 / 440
CLAAS LEXION 430 / 420
CLAAS LEXION 430 / 420
CLAAS LEXION 430 / 420
CLAAS LEXION 410
CLAAS LEXION 410
CLAAS LEXION 410
Safety devices
Front implements – weights, measurements
Before starting_x0011_start
Tasks to be performed before the first_x0004_ start-up
Cabin with Climatic
Climatic
Control and display elements
Put Climatic into operation
Set the cabin temperature
Manually adjust the fan speed_x0004_
Fully automatic heating
Manual heating programming
Foot heating
REHEAT operation (removing moisture from the cabin windshields)
Show outside temperature
Change the temperature to Fahrenheit
Fault/error indication on temperature meter F0 (compartment, blue)
Fault/error indication on temperature meter F1 (blown, yellow)
Fault/error indication on temperature meter F2 (out, red)
Cabin with air conditioning equipment (base equipment)
Cabin with air conditioning equipment
Heated cabin
Foot heating
REHEAT system (fogged windows)
Incident, possible causes and solutions – air conditioning equipment
Open and close the cabin roof
Window washing equipment
Driver’s platform
Driver Platform Presentation
Scorecard
Monitor (picture running)
Monitor (crop image)
Area C keys
Rotary switch D
steering bar
Ignition lock (S)
Multifunctional switch
Gait monitor
Multifunctional controller
Adjust the steering bar
Swing the top of the steering rod_x0004_
Steering wheel height adjustment
central electrical system
Extend and retract discharge tube
Safety device
Connect and disconnect the discharge of the grain tank_x0004_
Connecting and disconnecting the threshing unit
Driver’s seat
Mechanical driver’s seat
Driver’s seat with air suspension_x0004_ (optional equipment)
Front staircase
pivoting ladder
Ascent and widening of the staircase
Position lights for excessive width
Install position lights for excessive width
Back staircase
Other uses of the back staircase
Drive the combine
Rotary switch for engine speed_x0004_
Maneuver
Engine start
Servo-assisted gear shifting (optional equipment)
Adjustment of the hardness of the gear shift lever movement
Driving characteristics
Footbrake
Parking break
stop the engine
CLAAS autopilot (corn milking head)
CLAAS autopilot (cereal cutting tables)
Adjusting the straight line running of the combine
Orient the laser sensor relative to the field
Putting CLAAS Autopilot into service
Use in rapeseed with left side blade
Cutting table hydraulic cylinders
Engage the hydraulic cylinders
Third cylinder for the cutting table
Drive steering axle
Changing the drive steering axle from transport position to work position
Adjust the track width of the drive steering axle
Variable steering axle
Steering wheels – impact limitations (variable steering axle)
Side gates
Open and close the side doors and tailgate
Adjustment of the gate closures
Cabin and lighting
Running lights, work lights and mirrors
Trailer / harvest control / grain tank
Tow the combine
Backward
Harvest control
grain warehouse
Close the holes in the grain tank
Install the twin wheels
Front ladder handling with twin tires_x0004_
Additional weights
Fluid refill for steering axle wheels
Install additional weights on the steering axle
Volume of parts – steering axle weights (variable and fixed axle)
Parts volume – steering axle (steering drive axle) weights
Assemble and disassemble the_x0011_cutting table
Assemble the cutting table
Tip the cutting table out of the transport position
Machines with CLAAS-Auto-Contour
Adjustment of the hydraulic cylinders for transversal regulation of the cutting table
Machines without CLAAS-Auto-Contour
Fix corn cutting tables and milking heads (cutting tables without Auto-Contour)
Connect the cardan shafts
Install the support leg
Disassemble the cutting table
Disassemble the cutting table
Place the cutting table on the ground
Place the cutting table on the cutting table trailer
CEBIS Operation
Operation – base machine
Carrier feed channel_x0004_
Carrier Chains
Gear reversal equipment for cutting table
Cutting table discharge springs
Check the adjustment of the discharge springs
Cutting height indicator
Discharge indication
Lock the cutting table discharge springs
Adjust the lowering speed of the front implement_x0004_
Cutting table clutch
Connect and disconnect the cutting table
Threshing organs
Stone collecting device
Connecting and disconnecting the threshing mechanism
Sheller cylinder
Clean the threshing units
Basic concave adjustment
Learn final positions
Speed ​​of revolutions of the sheller cylinder_x0004_
Cylinder drives
Two scale variator
Assemble and disassemble the preconcave segments_x0004_
Threshing segments
Remove the threshing segment
Assemble the threshing segment
Shelling
Unclog the sheller cylinder
splash cloth
Shak Intensive shakers
Multi-finger separation system
Clean the shakers
Emergency Signal
Shaker steps
Rice steps
Middle shaker steps
Side steps
Parallel steps
CCM steps
Cleaning
sieve box
Preparation Fund
Lamellar sieves
Electrical regulation of the sieves
Dismantle the sieves
Assemble the screens
Tightening torque of axial screws for upper and lower screens
Basic adjustment of the screens
Harvest without the lower sieves
Cleaning fan
Regulation of fan revolutions_x0004_
LEXION 460 – 420 ventilated shaker
Adjusting the air nozzle for pre-separation LEXION 460 – 420
LEXION 460 – 420 air guide plate
LEXION 410 air guide plates
Choke caps for grass seeds and similar (additional equipment)
Dynamic slope compensation (clean 3-D)
Grain passage control unit
Augers and trays
Elevators
grain warehouse
Supplement for the grain tank – electric (9300 / 8500 liter grain tank)
Grain tank cover – mechanical (8100 / 7800 / 7300 liter grain tank)
Download grain bin
Help for downloading the_x0011_grain tank (additional equipment)
Grain tank discharge pipe
Retract and extend the grain tank_x0011_discharge tube
Discharge tube cleaning flaps
Safety screw for unloading the grain tank_x0011_
Connecting and disconnecting the grain tank discharge
Entrance to the grain warehouse
Automatic chain lubrication – grain tank discharge (additional equipment)
Straw chopper
Straw chopper (hydraulic)
Check before starting the chopper
Spreading width variation
Distribution funnel – height adjustment
Electrical variation of the spreader plates
Adjust chopping length
Cross knife adjustment
Start the chopper
Disconnect the chopper
Cutter position to hang the trailer from the cutting table
Reduce chopper revolutions
Change the position of the V-belts_x0011_(12)
Straw chopper
Straw chopper (Fixed straw chopper)
Check before starting the chopper
Spreading width variation
Distribution funnel – height adjustment
Electrical variation of the spreader plates
Adjust chopping length
Cross knife adjustment
Connect the chopper
Disconnect the chopper
Cutter position for towing the cutting table trailer
Lower the chopper revolutions
Chaff spreader/straw spreader
chaff spreader
Fold down the chaff spreader
straw spreader
Adjust spreading width
Screening and threshing frames
Sieve box
Threshing table
Sheller plates
Threshing segment
Incident, causes and solutions – base machine
Entertainment by_x0011_la_x0011_harvester
Important information for entertainment
Important information for entertainment and safety
Entertainment and lubricant tables
Entertainment tables
Lubricant charts
Hydraulic system
pressure accumulator
Check the oil level
Change hydraulic oil
Changing the hydraulic oil filter
Clean coarse filters
Filling instructions for oil change (Sauer 90 R 130 / 90 M 100)
Vent the hydraulic cylinders for transversal operation of the cutting table
Gears/brakes
Check the oil level
Change the oil
Two-step side reducers (20 t / 19 t / 20 t HD)
Check the oil level
Change the oil
Lateral reducers (planetary reducers)
Check the oil level
Oil change
Sheller cylinder reducer
Change the oil
Check the oil level
timing gear
Check the oil level
Change the oil
Grain tank discharge gear_x0011_grains_x0004_
Check the oil level
Change the oil
Adjust the gear shift
Foot brake and brake fluid
Parking break
conveyor channel
Tension the feed chains
Cleaning the vacuum cleaner (additional equipment)
elevator chains
Tension the grain tank elevator chain (machine without performance meter)
Tension the chain of the grain tank elevator (machine with yield meter)
Tension the return elevator chain
Drive belts / drive chains – base machine
General indications
General table of left drives
Drive Belts and Chains
General table of right drives_x0004_
Drive belts
Remove the cutting table drive belt (1) (cutting table drive without…
Install and adjust the cutting table drive belt (1)
Remove the cutting table drive belt (2) (cutting table drive with…
Put on and adjust the driving belt of the cutting table (2)
Remove the cutting table variator belt (3)
Assemble the belt of the variator of the_x0011_cutting table (3)
Remove the drive belt from the straw thrower_x0004_ (4)
Assemble and adjust the straw thrower drive belt (4)
Remove the drive belt from the cutting table gear train (5)
Assemble and adjust the cutting table gear train drive belt_x0011_(5)
Remove the drive belt from the hydraulic pump for the straw spreader (6)
Assemble and adjust the drive belt of the hydraulic pump for the de_x0011_straw spreader / …
Remove the main gear train drive belt (7)
Install and adjust the main gear train drive belt (7)
Remove the drive belt from the grain tank discharge gear train_x0011_(8)
Assemble and adjust the drive belt of the tank discharge gear train_x0011_de…
Remove the drive belt from the straw chopper gear train (9)
Assemble and adjust the drive belt of the straw chopper gear train (9)
Adjust the drive of the straw chopper
Release and remove the V-belt (10) from the cylindrical spring (G)
Install the V-belt (10) and tension it on the cylindrical spring (G)
Release and remove the V-belt (11) from the cylindrical spring (G)
Install the V-belt (11) and tension it on the cylindrical spring (G)
Loosen and remove the straw chopper drive belt (12) (hydraulic straw chopper)
Assemble the driving belt of the straw chopper_x0004_ (12) and tension it on the cylindrical spring (…
Remove the drive belt from the sieve box gear train (13)
Assemble and adjust the screen box gear train drive belt (13)
Remove the screen box gear train drive belt (14)
Assemble and adjust the screen box gear train drive belt (14)
Remove the sieve box drive belt (15)
Open the battery/tool ​​drawer:
Assemble and adjust the sieve box drive belt (15)
Remove the fan gear train drive belt (20)
Install and adjust the fan gear train drive belt (20)
Remove the fan drive belt_x0011_(21)
Install the fan drive belt_x0011_(21)
Remove the drive belt from the threshing organs variator (22)
Assemble the drive belt of the threshing organs variator_x0004_ (22)
Remove the drive belt from the shelling cylinder (23)
Assemble and adjust the sheller cylinder drive belt (23)
Remove the throttle drive belt_x0011_previous (24)
Install and adjust the pre-throttle drive belt (24)
Remove the vacuum cleaner drive belt_x0011_(28)
Assemble and adjust the vacuum cleaner drive belt (28)
hten the radiator screen drive belt (32)
Tension the vacuum cleaner drive belt_x0011_(34)
Remove the drive chain for the grain tank discharge_x0004_ (17)
Assemble and adjust the grain tank discharge drive chain (17)
Cab air conditioning equipment
Clean the filters
Clean the equipment installed on the cabin roof
Air conditioning equipment
Clean the condenser
Check the refrigerant level
Replace the dehumidifier filter
Necessary amount of refrigerant agent – ​​refrigerant_agent_x0011_R_x0011_134_x0011_a
compressor oil
Entertainment work before beginning_x0004_ the harvest
Extinguisher
Extinguisher
Compressed air equipment (additional equipment)
Connections for compressed air intake
Drain the air tank
pressure regulator
Straw chopper
Change the blades (hydraulic straw chopper)
Move the deburring blade down
Change the chopper blade
Return the deburring blade to its position_x0004_
Chathe blades (fixed straw chopper)
Remove the straw guide plate
Change the chopper blade
Assemble the straw guide plate
Change the counterblades
straw spreader
Install and adjust the timing belt
Speed ​​control_x0004_
Adjustment of emi induction
Instructions for preserving the combine during winter
Entertainment – ​​motor
Important information for entertainment
Important information for entertainment_x0004_ and safety_x0011_
Entertainment and lubricant tables
Entertainment table
Lubricants table
Entertainment – ​​motor
Engine overview
fuel circuit
Fuel tank
fuel cock
Water separator / fuel prefilter (standard equipment – ​​small version)
Disassembled fuel prefilter:
Water separator / fuel prefilter (additional equipment, instead of the fuel prefilter…
Fuel filter
Change the filter cartridge
Bleed the fuel system
Engine oil level check
Engine oil change
Emptyin Oil filter
Top up engine oil
Refrigeration system
Cooling liquid
Engine block water drain plugs
Water radiator
Fill the coolant
Overpressure
Antifreeze/anticorrosive
notice plate
Coolant temperature
Stop the overheated engine
Radiator Clean the water radiator
Air filter
alarm device
Clean the air filter screen
Clean the dry air filter
Clean the air filter
Safety cartridge
Electric system
Three-phase current generator
Engine incidents, causes and solutions
Engine conservation during_x0011_winter
Engine conservation
Greasing scheme
Lubricants and indications
Alphabetical index
Alphabetical index
0298_303_1_BA_ES_144.pdf
CEBIS Operation
CLAAS CEBIS on-board information system
CEBIS monitor and rotary switch_x0004_
C key area
Rotary switch D
Multifunctional handle M
Screen area E (crop box)
Rotary switch D
Before first use
Gear chart
harvest box
Cartography ON/OFF
Cartographic indication
Reel Presets
Horizontal reel position
Proportional reel speed
Reel height
Presets for the head
Distance between starter plates
Mowing mechanism table length
Cutting height adjustment (CAC)
Partial width switching
Harvest Measuring Equipment
Components
Basic and calibrated adjustment
Preparation for performance measurement
Humidity measurement ON/OFF, humidity correction, humidity to store
Fast track to achieving reasonable measurement data
Performance measurement
Calibration factor
Zero point performance
Checked weight
Humidity correction
Humidity measurement ON/OFF
Zero angle
Humidity to store
Dry product indication
Adjustment according to the type of fruit
List of types of fruit to thresh
Load CLAAS values
Load own values
Memorize own values
Print values
Enter CLAAS values
Indicate own values
Clean by blowing
to register
Planned jobs
Next planned work
Previous planned work
New work planned
Modify a planned job
Name / Plot / Fruit / Operator:
Start/Stop
Memorization data:
Dispatched jobs
Next or Previous job dispatched
New batch of a dispatched job
Correct the surface
daily counter
Print the daily counter
Cancel daily counter
Total counter
Print the total counter
Copy the chip card
Mowing mechanism
CAC Sensitivity
Cutting height stops
Graduation of partial heights
Work position
Working width
Automatic reel height
Reel Height Stops
Automatic mowing mechanism
Mech table length limits. mowing
Limits of horizontal adjustment of the reel
Varioautomatic ON/OFF
Starter plate stops
Revolution regime
Learn revolutions
R.P.M. max empty
Chaff spreader (without function for rotor machines)
Return lift revolution control
Tachometer
Calibration path
Pulses/100
Autopilot Sensitivity (ATP)
Head zero point with Autopilot
zero point direction
Separation
Test sensors
Final positions of the upper and lower sieves
Adjustment of the upper and lower sieves
Return limit indication
Return zero point
Language
Date hour
Measurement units
Time indication:
Maintenance
Jobs every XXh
Instructions for use
Basic adjustment
General standard settings:
Specific standard settings:
Adjustment guide
Incident/solution
Check list
Security measures
Security code
Disconnect security code:
engine load
Engine diagnosis
Incident/Solution – Harvest Measuring Equipment
Guideline values ​​for pulses/100 m
Alphabetical index

00 0298 597 0.pdf:

Introduction
Introduction
General indications
Circulation on public roads
Important note
Nameplate / Serial_x0011_number
Machine factory plate
Chassis number
CATERPILLAR C9 engine number
Engine number CATERPILLAR 3126 B
Factory plate – straw chopper
Cabin serial number
Security measures
Security measures
Security support
Extinguisher
Battery disconnect switch
Place the shims
Safety stickers with graphic danger symbols
Technical data
CLAAS LEXION 460 / 450 / 440
CLAAS LEXION 460 / 450 / 440
CLAAS LEXION 460 / 450 / 440
CLAAS LE 430 / 420
CLAAS LEXION 430 / 420
CLAAS LEXION 430 / 420
CLAAS LEXION 410
CLAAS LEXION 410
CLAAS LEXION 410
Safety devices
Front implements – weights, measurements
Before starting_x0011_start
Tasks to be performed before the first_x0004_ start-up
Cabin with Climatic
Climatic
Control and display elements
Put Climatic into operation
Set the cabin temperature
Manually set the fan speed
Fully automatic heating
Manual heating programming
Foot heating
REHEAT operation (removing moisture from the cabin windshields)
Show outside temperature
Change the temperature to Fahrenheit
Fault/error indication on temperature meter F0 (compartment, blue)
Fault/error indication on temperature meter F1 (blown, yellow)
Fault/error indication on temperature meter F2 (out, red)
Cabin with air conditioning equipment (base equipment)
Cabin with air conditioning equipment
Heated cabin
Foot heating
REHEAT system (fogged windows)
Incident, possible causes and solutions – air conditioning equipment
Open and close the cabin roof
Window washing equipment
Driver’s platform
Driver Platform Presentation
Scorecard
Monitor Zone A
Rotary switch D
Monitor Zone B
steering bar
Ignition lock (S)
Multifunctional switch
Gait monitor
Multifunctional controller
Adjust the steering bar
Swing the top of the steering rod_x0004_
Steering wheel height adjustment
central electrical system
Extend and retract discharge tube
Safety device
Connect and disconnect the discharge of the grain tank_x0004_
Connecting and disconnecting the threshing unit
Driver’s seat
Mechanical driver’s seat
Driver’s seat with air suspension_x0004_ (optional equipment)
Front staircase
pivoting ladder
Ascent and widening of the staircase
Position lights for excessive width
Install position lights for excessive width
Back staircase
Other uses of the back staircase
Drive the combine
Rotary switch for engine speed_x0004_
Maneuver
Engine start
Servo-assisted gear shifting (optional equipment)
Adjustment of the hardness of the gear shift lever movement
Driving characteristics
Footbrake
Parking break
stop the engine
CLAAS autopilot (corn milking head)
CLAAS autopilot (cereal cutting tables)
Adjusting the straight line running of the combine
Orient the laser sensor relative to the field
Putting CLAAS Autopilot into service
Use in rapeseed with left side blade
Cutting table hydraulic cylinders
Engage the hydraulic cylinders
Third cylinder for the cutting table
Drive steering axle
Changing the drive steering axle from transport position to work position
Adjust the track width of the drive steering axle
Variable steering axle
Steering wheels – impact limitations (variable steering axle)
Side gates
Open and close the side doors and tailgate
Adjustment of the gate closures
Cabin and lighting
Running lights, work lights and mirrors
Trailer / harvest control / grain tank
Tow the combine
Backward
Harvest control
grain warehouse
Close the holes in the grain tank
Install the twin wheels
Front ladder handling with twin tires_x0004_
Additional weights
Fluid refill for steering axle wheels
Install additional weights on the steering axle
Volume of parts – steering axle weights (variable and fixed axle)
Parts volume – steering axle (steering drive axle) weights
Assemble and disassemble the_x0011_cutting table
Assemble the cutting table
Tip the cutting table out of the transport position
Machines with CLAAS-Auto-Contour
Adjustment of the hydraulic cylinders for transversal regulation of the cutting table
Machines without CLAAS-Auto-Contour
Fix corn cutting tables and milking heads (cutting tables without Auto-Contour)
Connect the cardan shafts
Install the support leg
Disassemble the cutting table
Disassemble the cutting table
Place the cutting table on the ground
Place the cutting table on the cutting table trailer
IMO Operation
Operation – base machine
Carrier feed channel_x0004_
Carrier Chains
Gear reversal equipment for cutting table
Cutting table discharge springs
Check the adjustment of the discharge springs
Cutting height indicator
Discharge indication
Lock the cutting table discharge springs
Adjust the lowering speed of the front implement_x0004_
Cutting table clutch
Connect and disconnect the cutting table
Threshing organs
Stone collecting device
Connecting and disconnecting the threshing mechanism
Sheller cylinder
Clean the threshing units
Basic concave adjustment
Learn final positions
Speed ​​of revolutions of the sheller cylinder_x0004_
Cylinder drives
Two scale vaor
Assemble and disassemble the preconcave segments_x0004_
Threshing segments
Remove the threshing segment
Assemble the threshing segment
Shelling
Unclog the sheller cylinder
splash cloth
Intensive shakers
Multi-finger separation system
Clean the shakers
Emergency Signal
Shaker steps
Rice steps
Middle shakeeps
Side steps
Parallel steps
CCM steps
Cleaning
sieve box
Preparation Fund
Lamellar sieves
Electrical regulation of the sieves
Dismantle the sieves
Assemble the screens
Tightening torque of the axial screws for upper and lower sieves_x0004_
Basic adjustment of the screens
Harvest without the lower sieves
Cleaning fan
Regulation of fan revolutions_x0004_
LEXION 460 – 420 ventilated shaker
Adjusting the air nozzle for pre-separation LEXION 460 – 420
LEXION 460 – 420 air guide plate
LEXION 410 air guide plates
Choke caps for grass seeds and similar (additional equipment)
Dynamic slope compensation (clean 3-D)
Grain passage control unit
Augers and trays
Elevators
grain warehouse
Supplement for the grain tank – electric (9300 / 8500 liter grain tank)
Grain tank cover – mechanical (8100 / 7800 / 7300 liter grain tank)
Download grain bin
Help for downloading the_x0011_grain tank (additional equipment)
Grain tank discharge pipe
Retract and extend the grain tank_x0011_discharge tube
Discharge tube cleaning flaps
Safety screw for unloading the grain tank_x0011_
Connect and disconnect the grain tank discharge
Entrance to the grain warehouse
Automatic chain lubrication – grain tank discharge (additional equipment)
Straw chopper
Straw chopper (hydraulic)
Check before starting the chopper
Spreading width variation
Distribution funnel – height adjustment
Electrical variation of the spreader plates
Adjust chopping length
Cross knife adjustment
Start the chopper
Disconnect the chopper
Cutter position to hang the trailer from the cutting table
Reduce chopper revolutions
Change the position of the V-belts_x0011_(12)
Straw chopper
Straw chopper (Fixed straw chopper)
Check before starting the chopper
Spreading width variation
Distribution funnel – height adjustment
Electrical variation of the spreader plates
Adjust chopping length
Cross knife adjustment
Connect the chopper
Disconnect the chopper
Cutter position for towing the cutting table trailer
Lower the chopper revolutions
Chaff spreader/straw spreader
chaff spreader
Fold down the chaff spreader
straw spreader
Adjust spreading width
CLAAS-Auto-Contour
Automatic regulation of cutting height and transversal adaptation of the cutting table
Putting CLAAS Auto-Contour into operation
Second cutting height
Raise the cutting table
Putting CLAAS Auto-Contour back into operation
Pre-selection of cutting height with automatic_x0011_regulation (machines with CLAAS Auto-Contour)
Activate cutting height preselection
Program an additional cutting height
Adjustment table for automatic cutting height regulation
CLAAS-Contour (support pressure regulation)
Putting CLAAS-Contour into operation
Raise the cutting table
Screening and threshing frames
Sieve box
Threshing table
Sheller plates
Threshing segment
Incident, causes and solutions – base machine
Entertainment by_x0011_la_x0011_harvester
Important information for entertainment
Important information for entertainment and safety
Entertainment and lubricant tables
Entertainment tables
Lubricant charts
Hydraulic system
pressure accumulator
Check the oil level
Change hydraulic oil
Changing the hydraulic oil filter
Clean coarse filters
Filling instructions for oil change (Sauer 90 R 130 / 90 M 100)
Vent the hydraulic cylinders for transversal operation of the cutting table
Gears/brakes
Check the oil level
Change the oil
Two-step side reducers (20 t / 19 t / 20 t HD)
Check the oil level
Change the oil
Lateral reducers (planetary reducers)
Check the oil level
Change the oil
Sheller cylinder reducer
Change the oil
Check the oil level
timing gear
Check the oil level
Change the oil
Grain tank discharge gear_x0011_grains_x0004_
Check the oil level
Change the oil
Adjust the gear shift
Foot brake and brake fluid
Parking break
conveyor channel
Tension the feed chains
Cleaning the vacuum cleaner (additional equipment)
elevator chains
Tension the grain tank elevator chain (machine without performance meter)
Tension the chain of the grain tank elevator (machine with yield meter)
Tension the return elevator chain
Drive belts / drive chains – base machine
General indications
General table of left drives
Drive Belts and Chains
General table of the right drives_x0004_
Drive belts
Remove the cutting table drive belt (1) (cutting table drive without…
Install and adjust the cutting table drive belt (1)
Remove the cutting table drive belt (2) (cutting table drive with…
Put on and adjust the driving belt of the cutting table (2)
Remove the cutting table variator belt (3)
Assemble the belt of the variator of the_x0011_cutting table (3)
Remove the drive belt from the straw thrower_x0004_ (4)
Assemble and adjust the straw thrower drive belt (4)
Remove the drive belt from the cutting table gear train (5)
Assemble and adjust the cutting table gear train drive belt_x0011_(5)
Remove the drive belt from the hydraulic pump for the straw spreader (6)
Assemble and adjust the drive belt of the hydraulic pump for the de_x0011_straw spreader / …
Remove the main gear train drive belt (7)
Install and adjust the main gear train drive belt (7)
Remove the drive belt from the grain tank discharge gear train_x0011_(8)
Assemble and adjust the drive belt of the tank discharge gear train_x0011_de…
Remove the drive belt from the straw chopper gear train (9)
Assemble and adjust the drive belt of the straw chopper gear train (9)
Adjust the drive of the straw chopper
Release and remove the V-belt (10) from the cylindrical spring (G)
Install the V-belt (10) and tension it on the cylindrical spring (G)
Release and remove the V-belt (11) from the cylindrical spring (G)
Install the V-belt (11) and tension it on the cylindrical spring (G)
Loosen and remove the straw chopper drive belt (12) (hydraulic straw chopper)
Assemble the driving belt of the straw chopper_x0004_ (12) and tension it on the cylindrical spring (…
Remove the drive belt from the sieve box gear train (13)
Assemble and adjust the screen box gear train d