Claas LEXION 570 MONTANA (581) Combine Operator Manual DE

File List:

– 00 0293 178 7.pdf
– 00 0295 270 0.pdf
– 00 0299 766 0.pdf

00 0293 178 7.pdf

Table of Content:
1.1 1 Introduction
1.2 2 General information
1.3 3 For safety
1.4 4 Technical data
1.5 5 Before commissioning
1.6 6 Attaching and removing the cutting unit
1.7 7 Operation CEBIS (version 8.23)
1.8 8 Operation – basic machine
1.9 9 Maintenance – basic machine
1.10 10 Maintenance – Motor
1.11 11 Lubrication plan
1.12 Index

00 0295 270 0.pdf

Table of Content:
2 1 Introduction
2.1 1.1 General information
3 2 Before commissioning
3.1 2.1 Combine harvesters drive with mechanical / electro-hydraulic drive control
4 3 Maintenance – basic machine
4.1 3.1 Lubricant tables
5 4 Maintenance Motor
5.1 4.1 Maintenance tables
7 1 Introintenance – Basic machine
9.1 3.1 Lubricants charts
10 4 Engine maintenance
10.1 4.1 Maintenance schedules
12 1 Introduction
12.1 1.1 General Councils
13 2 Avant la mise en service
13.1 2.1 Conduite de la moissonneuse-batteuse with commande mecanique / lectrohydraulique d’avancement
14 3 Entretien – machine de base
14.1 3.1 Tableaux des lubricants
15 4 Maintenance motor
15.1 4.1 Tableaux dentretien
17 1 Introduction
17.1 1.1 General indications
18 2 Prima della messa in esercizio
18.1 2.1 Advancement of the rental engine with mechanical command / electric hydraulic
19 3 Manual – macchina base
19.1 3.1 Table of lubricants
20 4 Manual engine
20.1 4.1 Manual table
22 1 Introduction
22.1 1.1 General indications
23 2 Antes de la puesta en marcha
23.1 2.1 Conducir the cosechadora with an accionamiento de motor
25.1 4.1 Tablas de mantenimiento

00 0299 766 0.pdf

Table of Content:
1 Introduction
1.1 Introduction
2.1 Content
3 General information
3.1 Road traffic
3.2 Particular attention should be paid to
3.3 Type plate / serial number
4 For safety
4.1 For safety
4.2 Safety sticker with warning symbols
5 Technical data
5.1 CLAAS LEXION 570 Montana
5.2 Safety devices
6 Before commissioning
6.1 Carry out before initial commissioning
6.3 Driver’s cab
6.4 Lighting and sockets
6.5 Advancement ladder
6.6 Side flaps
6.7 Mudguard
6.8 Steering axles
6.9 Additional weights steering axle
6.10 Cutting unit hydraulic cylinder
6.11 Grain tank
6.12 Driving a combine harvester
6.13 CLAAS autopilot (corn picker)
6.14 Malfunction, possibl CEBIS
8.1 Content
8.2 CLAAS on-board information system CEBIS
8.3 CEBIS monitor and rotary switch
8.4 Rotary switch D
8.5 Before initial commissioning
8.6 Driving image
8.7 Harvest image
8.8 Flagging
8.10 Presets Haspel
8.11 Presets attachment
8.12 Section switching
8.13 Yield measuring device
8.14 Yield measurement
8.15 Fruit-dependent setting
8.16 Register
8.17 Setting
8.18 Motor utilization
8.19 Alarms
8.20 Messages
8.21 Malfunction / Remedy – Yield Measuring Device
8.22 Guide values for pulses/100 m
8.23 Yield Mapping
9 Operation basic machine
9.1 Feed channel
9.2 Threshing organs
9.3 Axial rotors LEXION 570 Montana
9.4 Cleaning
9.5 Grain recoverne
10.1 Important maintenance instructions
10.2 Maintenance and lubricant tables
10.3 Hydraulic system
10.4 Gearbox
10.5 Feed channel
10.6 Drive axis
10.7 Elevator chains
10.8 Drive belts / drive chains basic machine
10.9 Cabin / Air conditioning
10.10 Fire extinguisher_x0004_
10.11 Compressed air system (additional equipment)
10.12 Straw chopper (LEXION 570 Montana)
10.13 Winterization suggestions for combine harvesters
11 Maintenance Engine
11.1 Important maintenance instructions
11.2 Maintenance and lubricant tables
11.3 Maintenance Motor
11.4 Fuel system / engine oil
11.5 Cooling system
11.6 Dry air filter
11.7 Three-phase generator
11.8 Electrics
11.9 Engine