Claas LEXION 580R CAT (578) Combine Operator Manual DE

File List:

– 00 0288 706 0.pdf
– 00 0294 356 1.pdf
– 00 0299 943 5.pdf

00 0288 706 0.pdf

Table of Content:
1 LEXION 780 – 670LEXION 770 – 670CAT LEXION 590 R – 560CAT LEXION 485 R – 450

00 0294 356 1.pdf

Table of Content:
2 1 Introduction
2.1 1.1 General information
3 2 Security
3.1 2.1 Note
3.2 2.2 Warning symbol
4 3 Technical data
4.1 3.1 General information
4.2 3.2 CAT LEXION 595 R
4.3 3.3 CAT LEXION 585 R / 575 R
5 4 Work input
5.1 4.1 Operation
6 5 Maintenance
6.1 5.1 Important maintenance instructions
6.2 5.2 Maintenance tables
7 6 Lubrication plan
7.1 6.1 Lubrication points
8.1hnical data
4.1 3.1 Machine overview
4.2 3.2 General information
4.3 3.3 CAT LEXION 590 R
4.4 3.4 CAT LEXION 580 R / 570 R
4.5 3.5 CAT LEXION 560 R
4.6 3.6 System descriptions
4.7 3.7 Type plate / serial number
5 4 Before commissioning
5.1 4.1 General information
5.2 4.2 Cabin
5.3 4.3 Lighting and sockets
5.4 4.4 Side flaps
5.5 4.5 Mudguard
5.6 4.6 Steering axles
5.7 4.7 Cutting unit hydraulic cylinder
5.8 4.8 Twin wheels
5.9 4.9 Grain tank
5.10 4.10 Combine harvester driving CAT LEXION 595 R / 590 R with electro-hydraulic driving control
5.11 4.11 Combine harvester driving CAT LEXION 585 R – 570 R with mechanical drive control
5.12 4.12 CLAAS autopilot (corn picker)
5.13 4.13 CLAAS autopilot (grain cutter)
6 5 Attaching/removing the attachment
6.1 5.1 General warnings
6.2 5.2 General assemblies and settings
6.3 5.3 Drives
6.4 5.4 Hydraulics
6.5 5.5 Machine housing
7 6 Operation CEBIS (version 9.22)
7.1 6.1 CLAAS on-board information system CEBIS
7.2 6.2 CEBIS monitor and rotary switch
7.3 6.3 Rotary switch D
7.4 6.4 Before initial commissioning
7.5 6.5 Driving image
7.6 6.6 Harvest image
7.7 6.7 CLAAS CRUISE PILOT
7.8 6.8 Yield Mapping
7.9 6.9 Flagging
7.10 6.10 GPS
7.11 6.11 Presets Haspel
7.12 6.12 Presets attachment
7.13 6.13 Section switching
7.14 6.14 Yield measuring device
7.15 6.15 Yield measurement
7.16 6.16 Fruit-dependent setting
7.17 6.17 Register
7.18 6.18 Set
7.19 6.19 Motor utilization
7.20 6.20 Alarms
7.21 6.21 Messages
7.22 6.22 Malfunction / Remedy – Yield measuring device
7.23 6.23 Guide values for pulses/100 m
8 7 Operation – basic machine
8.1 7.1 HP feed channel
8.2 7.2 Standard feed channel
8.3 7.3 Threshing organs
8.4 7.4 Aer
8.9 7.9 Chaff spreader
8.10 7.10 Straw distributor
8.11 7.11 Sieving and threshing tables
8.12 7.12 Unawning
8.13 7.13 Malfunction, cause or remedy – basic machine
9 8 Maintenance – basic machine
9.1 8.1 Important maintenance instructions
9.2 8.2 Maintenance tables
9.3 8.3 Lubricant tables
9.4 8.4 Hydraulic system
9.5 8.5 Gearbox / Brakes
9.6 8.6 HP feed channel
9.7 8.7 Standard feed channel
9.8 8.8 deposition
9.9 8.9 Elevator chains
9.10 8.10 Drive belts / drive chains
9.11 8.11 Cabin / Air conditioning
9.12 8.12 Fire extinguisher
9.13 8.13 Straw chopper
9.14 8.14 Winterization
10 9 Maintenance – Motor
10.1 9.1 Important maintenance instructions
10.2 9.2 S O S liquid analysis
10.3 9.3 Maintenance tables
10.4 9.4 Lubricant tables
10.5 9.5 Engine overview
10.6 9.6 Fuel system / engine oil
10.7 9.7 Cooling system
10.8 9.8 Dry air filter
10.9 9.9 Three-phase generator
10.10 9.10 Electrics / Electronics
10.11 9.11 Malfunction, possible cause or remedy
10.12 9.12 Winterization
11 10 Lubrication plan
11.1 10.1 Lubrication points
12 11 Service Information
12.1 11.1 Troubleshooting