Claas Liner 3500 (G04) Swathers Technical System ES

File List:

00 0291 216 2.pdf

00 0291 216 2.pdf:

LINER 3500
Introduction
Safety instructions
Safety and danger instructions
CCN Explanation
CCN (CLAAS Component Number)
General indications
Electrical regulations
Hydraulic regulations
CCN (CLAAS Component Number)
09 Hydraulic
0920 Valves
LINER 3600 valve block
Function Description
0980 Hydraulic connection diagram
LINER 3500 hydraulic connection diagram
Function Description
10 Install. electrical/electronic
1012 Modules / sensors
CLAAS CONTROL UNIT module (A020)
Pin occupation
Drive speed sensor (B009)
Pin occupation
Function Description
Adjustment
Table of measured values
Chassis position sensor (B284)
Pin occupation
Function Description
Adjustment
Table of measured values
Left front rotor position sensor (B285)
Pin occupation
Function Description
Adjustment
Table of measured values
Right front rotor position sensor (B286)
Pin occupation
Function Description
Adjustment
Table of measured values
Left rear rotor position sensor (B287)
Pin occupation
Function Description
Adjustment
Table of measured values
Right rear rotor position sensor (B288)
Pin occupation
Function Description
Adjustment
Table of measured values
Raking height sensor (B311, B312, B313, B314)
Function Description
Adjustment
Pin occupation
Table of measured values
1080 Electronic connection diagram
LINER 3500 electrical connection diagram
SCM 01 – Power supply / CAN-Bus
Denominations
SCM 02a – ISO-Bus connection
Denominations
SCM 02b – Control unit – COMMUNICATOR
Denominations
SCM 02c – Control unit – CLAAS Standard Terminal
Denominations
SCM 03 – Chassis
Denominations
SCM 04 – Front rotors
Denominations
SCM 05 – Rear rotors
Denominations
SCM 06a – Advance lighting – standard
Denominations
SCM 06b – Advance lighting – contour lighting option
Denominations
SCM 06c – Advance lighting – work lighting option
Denominations
SCM 06d – Advance lighting – work lighting / contour lighting option
Denominations
SCM 07 – Lighting for work
Denominations
1085 Networks
92 Diagnosis
9210 Machine Error Codes
FMI fault code (Failure Mode Indicator)
General indications
FMI 00 (signal too large)
FMI 01 (signal too small)
IMF 02 (implausible signal)
FMI 03 (voltage too high)
FMI 04 (voltage too low)
FMI 05 (current too low)
FMI 06 (current too high)
FMI 07 (mechanical failure)
FMI 08 (frequency signal defective)
IMF 09 (communication failure)
FMI 10 (signal change too fast)
IMF 11 (multiple failure)
FMI 12 (defective ECU)
FMI 13 (signal outside calibration range)
IMF 16 (non-existent parameter)
FMI 17 (ECU not responding)
FMI 18 (power supply failure)
FMI 19 (software requirements not met)
IMF 95 (no signal change)
FMI 96 (CAN-Bus system defective)
IMF 97 (implausible state)
IMF 98 (warning)
IMF 99 (Info)
Error code table
Location of components
Hydraulic installation
1000 Oil tank / oil filter / oil radiator
3000 Hydraulic Cylinders
6000 Valves – with mechanical drive
7000 Valves – hydraulically actuated
8000 Couplings/connections
Electrical installation
To Terminal/modules
SectionHead
B Sensors
K Relays
R Potentiometer/ resistors
X Pluggable connections
and electromagnetic coil