Claas Liner 430 S (392) Swathers Operator Manual EN

File List:

00 0299 870 3.pdf
00 2348 408 0.pdf
00 2348 427 0.pdf

00 0299 870 3.pdf:

1 Basic components of the machine
2 Introduction
Introduction
Validity
3 Contents
4 Preface
Of special importance
Identification Plate
5 Safety Rules
Intended use
Avoidable incorrect applications
General safety regulations and safety precautions
De-commissioning and disposal
Identification of warning and hazard signs
Safety Decals with warning symbols
6 Technical data
LINER 470 S
LINER 430 S
LINER 390 S
LINER 350 S
Calculation of axle loads, minimum ballasting and total weight
Calculation of minimum ballasting at the front
Calculation of minimum ballasting at the rear
Calculation of the real front axle load
Calculation of the real total weight
Calculation of the real rear axle load
Tyre load carrying capacity
7 Assembly
Loading and unloading machine
Initial assembly of machine
Assembly Instructions
Mounting the warning panels
8 Prior to operation
Check every time prior to operation
Hitching up
Headstock
Universal drive shaft
Swath disc
Lowering the machine
Prior to transportation
Driving on public roads
Identification of the machine for road traffic
Warning plates with lighting
9 Operation
Field operation
Working position
Adjusting the swathing deflector
Height adjustment of the rotary assembly
Swath forming adjustment
Putting the swather to work
Transport position
Optional Equipment
3-point linkage – gauge wheel
Universal joint yoke kit
10 Maintenance
Important maintenance instructions
Wheels and tyres
Lubrication
Safety frame
Rotor gearcase
Swather gearbox LINER 470 S / 430 S / 390 S
Sealing the rotor gearcase
Clamping bearing – version with seal already applied
Clamping bearing – version without seal already applied
Swather gearbox LINER 350 S
PTO drive shaft
Screw connections
Spring tines
Fasteners
Cleaning and care
Winter storage
11 Lubrication chart
Safety precaution
Lubricating grease
Lubrication

00 2348 408 0.pdf:

CEMIS 100
Table of contents
1 Introduction
1.1 General information
1.1.1 Validity of the manual
1.1.2 Information about this Operator’s Manual
1.1.3 Symbols and notes
1.2 Intended use
1.2.1 Intended use
1.2.2 Reasonably foreseeable misuse
2 Safety
2.1 Safety rules
2.1.1 General safety and accident prevention regulations
2.1.2 Interaction between terminal and machine or tractor
2.1.3 Electrocution by electrical system
3 Product description
3.1 Overview and method of operation
3.1.1 Overview of CEMIS 100
3.1.2 Function principle of CEMIS 100
3.2 Identification plates and identification numbers
3.2.1 Spare parts and technical questions
3.2.2 Identification plate of CEMIS 100
4 Operating and display elements
4.1 CEMIS 100
4.1.1 User interface for LINER
4.1.2 User interface for ROLLANT
4.1.3 User interface for UNIWRAP
5 Technical specifications
5.1 CEMIS 100
5.1.1 Specification
6 Operation
6.1 CEMIS 100
6.1.1 Operating the CEMIS 100
6.1.2 Switching CEMIS 100 on
6.1.3 Switching CEMIS 100 off
7 Maintenance
7.1 CEMIS 100
7.1.1 Daily
8 Putting out of operation and disposal
8.1 General information
8.1.1 Removal from service and disposal
9 Technical terms and abbreviations
9.1 Terms and explanations
9.1.1 Technical words
9.1.2 Abbreviations

00 2348 427 0.pdf:

CEMIS 700
Table of contents
1 Introduction
1.1 General information
1.1.1 Validity of the manual
1.1.2 Information about this Operator’s Manual
1.1.3 Symbols and notes
1.2 Intended use
1.2.1 Intended use
1.2.2 Reasonably foreseeable misuse
2 Safety
2.1 Safety rules
2.1.1 General safety and accident prevention regulations
2.1.2 Interaction between terminal and machine or tractor
2.1.3 Electrocution by electrical system
3 Product description
3.1 Overview and method of operation
3.1.1 Overview of CEMIS 700
3.1.2 Function principle of CEMIS 700
3.2 Identification plates and identification numbers
3.2.1 Spare parts and technical questions
3.2.2 Identification plate of CEMIS 700
4 Information on the product
4.1 Software version
5 Operating and display elements
5.1 CEMIS 700
5.1.1 User interface
5.1.2 Terminal program
6 Technical specifications
6.1 CEMIS 700
6.1.1 Specification
7 Operation
7.1 CEMIS 700
7.1.1 Operating the CEMIS 700
7.1.2 Switching CEMIS 700 on
7.1.3 Switching CEMIS 700 off
7.2 Terminal settings
7.2.1 Making settings
Making settings with the rotary button
Making settings with the touch function
7.2.2 Setting the screen lighting
Daytime mode
Nighttime mode
Activating automatic key lighting
7.2.3 Setting the time and date
7.2.4 Displaying diagnosis information
On-board power supply voltage display
Display of CLAAS ISOBUS ECU address and name
7.2.5 Setting the language and display formats
Setting the language
Setting display formats
7.2.6 Setting the volume
7.2.7 Deleting an ISOBUS implement
8 Maintenance
8.1 Maintenance
8.1.1 Daily
9 Putting out of operation and disposal
9.1 General information
9.1.1 Removal from service and disposal
10 Technical terms and abbreviations
10.1 Terms and explanations
10.1.1 Technical words
10.1.2 Abbreviations