Claas Liner 650 Twin (607) Swathers Operator Manual EN

File List:

00 0293 557 2.pdf
00 2348 408 0.pdf
00 2348 427 0.pdf

00 0293 557 2.pdf:

1 Machine description
2 Introduction
Introduction
3 Contents
4 Preface
Of special importance
Identification label
5 Safety instructions
Designated use
General safety and accident prevention regulations
Identification of warning and danger signs
Safety decals with pictorials
6 Specifications
LINER 650 TWIN
7 Assembly
Unloading/loading the machine
Attaching machine for the first time
8 Prior to operation
Items to check and observe before operation
Hitching to the tractor
Hitching to the tractor linkage drawbar
Universal drive shaft
Inspection and adjustment of the universal drive shaft
Shortening the drive shaft
Fitting the drive shaft on the machine side
Connecting the drive shaft on the tractor side
Electrical connections
Hydraulic connections
Parking the machine
Before transport
Road travel
9 Operation
Field operation
Lowering the rotors into working position
Tine arm
Windrowing rubber
Hydraulic adjustment of windrowing rubber
Swing rotors into working position
Settings
Adjust rotor (basic setting)
Front rotor
With gauge wheel (additional accessory): Set gauge wheel (1) in such a way that the machine is approx. horizontal.
Rear rotor
Rotor height adjustment
Hydraulic system restrictor valve
Adjust rotor cover
Adjust windrowing rubber
Putting the rotary swather into operation
Headland setting
Possible applications
Single swath deposition
Double swath deposition
Accessory equipment
Additional gauge wheel
Hydraulic adjustment of windrowing rubber
Second windrowing rubber
Hydraulic following control
Hydraulic couplings for tractors
Slip yoke kit
Adapter for USA road lighting
Warning plate kit France
10 Maintenance
Important maintenance instructions
Wheels and tyres
Hydraulic system
Screws and bolts
Lubrication
Guards (Safety Frame)
Reduction gear
Angle drive
Bevel gears top
Bevel gears bottom
Drive shafts
General information concerning drive shafts
Hydraulics
Hydraulic hoses
Threaded fasteners
Tine rotors
Spring tine
Fasteners
Safety guards
Road wheels
Cleaning and care
Winter storage
11 Lubrication chart
Safety rules
Lubricants
Lubrication

00 2348 408 0.pdf:

CEMIS 100
Table of contents
1 Introduction
1.1 General information
1.1.1 Validity of the manual
1.1.2 Information about this Operator’s Manual
1.1.3 Symbols and notes
1.2 Intended use
1.2.1 Intended use
1.2.2 Reasonably foreseeable misuse
2 Safety
2.1 Safety rules
2.1.1 General safety and accident prevention regulations
2.1.2 Interaction between terminal and machine or tractor
2.1.3 Electrocution by electrical system
3 Product description
3.1 Overview and method of operation
3.1.1 Overview of CEMIS 100
3.1.2 Function principle of CEMIS 100
3.2 Identification plates and identification numbers
3.2.1 Spare parts and technical questions
3.2.2 Identification plate of CEMIS 100
4 Operating and display elements
4.1 CEMIS 100
4.1.1 User interface for LINER
4.1.2 User interface for ROLLANT
4.1.3 User interface for UNIWRAP
5 Technical specifications
5.1 CEMIS 100
5.1.1 Specification
6 Operation
6.1 CEMIS 100
6.1.1 Operating the CEMIS 100
6.1.2 Switching CEMIS 100 on
6.1.3 Switching CEMIS 100 off
7 Maintenance
7.1 CEMIS 100
7.1.1 Daily
8 Putting out of operation and disposal
8.1 General information
8.1.1 Removal from service and disposal
9 Technical terms and abbreviations
9.1 Terms and explanations
9.1.1 Technical words
9.1.2 Abbreviations

00 2348 427 0.pdf:

CEMIS 700
Table of contents
1 Introduction
1.1 General information
1.1.1 Validity of the manual
1.1.2 Information about this Operator’s Manual
1.1.3 Symbols and notes
1.2 Intended use
1.2.1 Intended use
1.2.2 Reasonably foreseeable misuse
2 Safety
2.1 Safety rules
2.1.1 General safety and accident prevention regulations
2.1.2 Interaction between terminal and machine or tractor
2.1.3 Electrocution by electrical system
3 Product description
3.1 Overview and method of operation
3.1.1 Overview of CEMIS 700
3.1.2 Function principle of CEMIS 700
3.2 Identification plates and identification numbers
3.2.1 Spare parts and technical questions
3.2.2 Identification plate of CEMIS 700
4 Information on the product
4.1 Software version
5 Operating and display elements
5.1 CEMIS 700
5.1.1 User interface
5.1.2 Terminal program
6 Technical specifications
6.1 CEMIS 700
6.1.1 Specification
7 Operation
7.1 CEMIS 700
7.1.1 Operating the CEMIS 700
7.1.2 Switching CEMIS 700 on
7.1.3 Switching CEMIS 700 off
7.2 Terminal settings
7.2.1 Making settings
Making settings with the rotary button
Making settings with the touch function
7.2.2 Setting the screen lighting
Daytime mode
Nighttime mode
Activating automatic key lighting
7.2.3 Setting the time and date
7.2.4 Displaying diagnosis information
On-board power supply voltage display
Display of CLAAS ISOBUS ECU address and name
7.2.5 Setting the language and display formats
Setting the language
Setting display formats
7.2.6 Setting the volume
7.2.7 Deleting an ISOBUS implement
8 Maintenance
8.1 Maintenance
8.1.1 Daily
9 Putting out of operation and disposal
9.1 General information
9.1.1 Removal from service and disposal
10 Technical terms and abbreviations
10.1 Terms and explanations
10.1.1 Technical words
10.1.2 Abbreviations