Claas Medion 330 H (931) Combines Assembly Instruction EN

File List:

00 0290 143 2.pdf
00 0292 437 0.pdf
00 0298 270 2.pdf
00 0298 292 1.pdf
00 0299 188 2.pdf
00 0299 356 0.pdf
00 0300 374 1.pdf

00 0298 292 1.pdf:

1 Instructions
1.1 Allgemeine Hinweise
1.1.1 Handling of the connection
1.1.2 Instructions of the connection
2 Sicherheit
2.1 Beachten
2.1.1 Sonders on the beach
2.1.2 Kennzeichnung von Warn- und Gefahrenhinweisen
3 Lieferumfang
3.1 Wind speed for low-turbocharged conditions
3.1.1 Delivery number 000 304 989 2
3.2 Wind speed for Zweifach-Turbogeblse
3.2.1 Delivery number 000 304 988 2
3.3 Wind reduzierung fr Tonnengeblse
3.3.1 Nachrustsatz 000 058 062 0
4.1 Wind control
4.1.1 Wind control for turbocharged connections
4.1.2 Wind reduzierung fr Tonnengeblse anbauen
1 Introduction
1.1 General Information
1.1.1 How to use this manual
1.1.2 Validity of instructions
2 Safety precautions
2.1 Important
2.1.1 Impoentification of warning and danger signs
3 Package list
3.1 Fan blast reduction kit for triple turbo fan
3.1.1 Supplementary kit 000 304 989 2
3.2 Fan blast reduction kit for double turbo fan
3.2.1 Supplementary kit 000 304 988 2
3.3 Fan blast reduction kit for cleaning fan
3.3.1 Supplementary kit 000 058 062 0
4 Mounting
4.1 Fan blast reduction kit
4.1.1 Installing the fan blast reduction kit for turbo fan
4.1.2 Installing the fan blast reduction kit for the cleaning fan
1 Introduction
1.1 General advice
1.1.1 Use of the instructions
1.1.2 Validity of the notice
2 Safety Tips
2.1 Observe
2.1.1 Important
2.1.2 Marking of warnings and dangers
3 pieces supplied
3.1 Reduction of ventilation for the triple turbo fan
3.1.1 Retrofit kit 000 304 989 2
3.2 Reduction of ventilation for the double turbo fan
3.2.1 Retrofit kit 000 304 988 2
3.3 Reduction of ventilation for barrel fan
3.3.1 Retrofit kit 000 058 062 0
4 Assembly
4.1 Reduction of ventilation
4.1.1 Installation of the ventilation reduction for turbo fan
4.1.2 Installation of the ventilation reduction for barrel fan
2.1.2 i Install pendulum control unit with accessories
Create negative pressure in the hydraulic lines
Remove the rear wall of the cabin (MEDION 340 – 310) (MEDION 330 H)
Set the sieve box to the middle position
Set 3D cleaning
Adjust the swivel fork
Bleed the pendulum control (30).
Remove baffles
Prepare and carry out a test run
Fitting instructions
3D Cleaning System
1 Introduction
Introduction
2 contents
Contents
3 General information
Important
Identification of warnings and danger signs
Correct use
4 Shipping Package
Shipping package
Supplementary kit 000 759 704 0
5 Installation
Fitting the 3-D cleaning system for the sieve pan
Preparing the installation
Removing the rocker arm
Fitting the holder with accessories
Fitting the pendulum control unit with accessories
Creating vacuum in the hydraulic lines
Removing the cab rear panel
Setting the sieve pan to the middle position
Setting the 3-D cleaning system
Setting the pivot arm
Bleeding the pendulum control (30)
Removing the guiding plates
Preparing and performing the test run
Notice of assembly
Net yage 3-D
1 Introduction
Introduction
2 Contenu
3 general councils
Important
Identification of the prescriptions concerning the avertissements and the dangers
Utilization conforme l’emploi prvu
4 pieces fournies
Pieces fournies
Additional equipment equipment 000 759 704 0
5 assely
Assembly nettoyage 3-D
Prepare the assembly
Dmonter le balancer
Monter le support with accessories
Monter lappareil de commande pendule with accessories
General depression in the hydraulic fluid conduits
Dmonter la paroi arrire de la cabine
Control the caisson de ne 3-D netting regulator
Adjustable four-way regulator
Purger the command of the pendulum (30)
Enlever les tles de guidage
Prepare and effect a marche d’essai

00 0299 356 0.pdf:

Anbauanleitung
Rundumleuchte
1 Instructions
Instructions
2 Inhalt
3 Allgemeine Hinweise
Besons on the beach
Kennzeichnung von Warn- und Gefahrenhinweisen
Bestimmungsgeme Verwendung
4 Lieferumfang
Lieferumfang
Contact details 012 962.1
Rundumleuchte anbauen
Anbau vorbereiten
r (1) included
Schaltrelais (4) included
Rundumleuchte (8) to be connected
Rundumleuchte (10) hinten anbauen
Probelauf vorbereiten und durchfhren
Fitting Instructions
Warning beacon
1 Introduction
Introduction
2 Contents
3 General information
Important
Identification of warnings
4 Shipping Package
Shipping Package
Supplementary kit 012 962.1
5 Installation
Installing the warning beacon
Preparing the installation
Installing the rotary switch_x0011_(1)
Installing the control relay_x0011_(4)
Installing the warning beacon_x0011_(8) on the front
Installing the warning beacon_x0011_(10) on the rear
Preparing and performing the test run
Installation instructions
1 Introduction
Introduction
2 Content
3 General tips
Important
Identification of warning and hazard reuirements
Use in accordance with intended use
4 pieces supplied
Parts supplied
Additional equipment set 012 962.1
5 Assembly
Mounting the rotating lights
Preparing for assembly
Mounting the rotary switch_x0011_(1)
Mounting the relay_x0011_(4)
Mounting the rotating beacon_x0011_(8) at the front
Mounting the beacon_x0011_(10) at the rear
Preparing and executing a test run