Claas Mega 350 (835) Combines Technical System FR

File List:

00 0291 028 2.pdf
00 0293 813 2.pdf
00 0293 814 2.pdf
00 0299 506 2.pdf
00 0299 507 2.pdf

00 0291 028 2.pdf:

MB OM460LAMB OM502LAMB OM906LAMB OM926LA
Contents
CCN explanation
CCN (CLAAS Component Number – CLAAS part number)
Electrical standard
Overview
Hydraulic standard
Overview
CCN (CLAAS Component Number – CLAAS part number)
Introduction
Safety tips
Safety instructions and risk information
Validity of the notice
Validity of the notice
01 Motor
0125 Injection system, fuel supply
PLD Injection/Fuel System
PLD injection system
Function description
Plug-in pump power phases
Function description
Plug-in pump control
Function description
Classification of plug-in pumps
Example of plug-in pump nameplate
Coding, example of plug-in pump nameplate
Low fuel pressure measurement
Special tool
Preparing for low fuel pressure measurement
Function description
Measured values, low fuel pressure (after fuel filter)
0155 Engine controls
Diesel engine monitoring, diesel engine (MB TIER 3) TUCANO, JAGUAR
Measurement value table
Function description
Diesel engine monitoring, diesel engine (MB TIER 3) LEXION
Measurement value table
Function description
Diesel engine monitoring, diesel engine (MB TIER 4i) TUCANO, JAGUAR
Measurement value table
Function description
Torque limitation in case of urea shortage
Function description
Torque limitation in case of lack of urea quality
Function description
Torque limitation in case of time exceeded with system errors
Function description
Diesel engine monitoring, diesel engine (MB TIER 4i) LEXION
Measurement value table
Function description
Torque limitation in case of urea shortage
Function description
Torque limitation in case of lack of urea quality
Function description
Torque limitation in case of time exceeded with system errors
Function description
0165 Exhaust gas aftertreatment
MB TIER 4i compressed air system (LEXION, TUCANO)
Function description
Air dryer with integrated pressure regulator
Function description
Compressed air system MB TIER 4i (JAGUAR)
Function description
Air dryer with integrated pressure regulator
Function description
SCR system – Urea heating and injection
Function description
Combined filling level / urea temperature sensor
Function description
Urea pump unit
Function description
Reduction Catalyst Temperature Sensors
Function description
Dosing unit
Function description
NOx sensor
Function description
Combined sensor for intake air humidity and temperature
Function description
10 Electrical/electronic system
1012 Modules – Sensors
Module overview – MB (OM460LA, 502LA, 906LA, 926LA)
Designations
Module A015 – electronic engine management (ECM) – MB TIER 4i
Connector X1
Designations
Module allocation, connector X1
Connector X2, plug 1 of 2, inline 6 and V8 engine
Module allocation, connector X2 plug 1 of 2
Connector X2, plug 2 of 2, motor in line 6
Module allocation, connector X2 plug 2 of 2, motor in line 6
Connector X2, plug 2 of 2, V8 engine
Module allocation, connector X2, plug 2 of 2, V8 engine
Module A017 – Engine adaptation (ADM) – MB TIER 3
Designations
Designations
Module A017 – Engine adaptation (ADM) – MB TIER 4i
Designations
Designations
Module A032 – Reduction catalyst (SCR) – MB TIER4i
Designations
Designations
MB OM460LA sensors
Illustration of sensors
MB 502LA sensors
Illustration of sensors
MB sensors OM 906LA, OM 926LA
Illustration of sensors
1085 Network functions
BUS (CAN) system – Motor and machine
Function description
92 Diagnosis
Diagnosis according to error codes
9220 Diesel Engine Error Codes (J1939)
FMI (Failure Mode Indicator) error code
FMI (Failure Mode Indicator) error code
FMI 00 (Signal too large)
FMI 01 (signal too small)
IMF 02 (Implausible signal)
FMI 03 (voltage too high)
FMI 04 (voltage too low)
FMI 05 (current too low)
FMI 06 (current too high)
FMI 07 (mechanical error)
FMI 08 (frequency signal defective)
FMI 09 (communication error)
FMI 10 (signal modification too fast)
FMI 11 (multiple error)
FMI 12 (ECU faulty)
FMI 13 (signal outside calibration range)
FMI 16 (non-existent parameter)
FMI 17 (ECU not responding)
FMI 18 (voltage supply error)
FMI 19 (software conditions not met)
FMI 95 (no signal modification)
FMI 96 (CAN-bus system defective)
IMF 97 (implausible state)
IMF 98 (alarm)
IMF 99 (News)
Error Codes
J1939 Diesel Engine Error Code List (MB)
Function description

00 0293 813 2.pdf:

MEGA 370 – 350 from machine number 845 00387, 835 00361 – Technical systems, Hydraulic system
Chapter 1 General hydraulics
1.1 General hydraulic system control plan
1.2 Oil tank, oil specification, filling quantity, oil change, oil filter, oil pressure
1.3 Hydraulic pumps
Chapter 2 Steering hydraulics
2.1 Hydraulic steering control plan without AUTOPILOT
2.2 Control plan with AUTOPILOT
2.3 Steering valve block
2.4 Function of neutral steering
2.5 Management check
2.6 AUTOPILOT left/right solenoid valve
2.7 Checking the AUTOPILOT system
Chapter 3 Operating Hydraulics
3.1 Operating hydraulics control plan
3.2 Main valve with cut-off valve, pressure limiter, raising/lowering of the front tool
3.3 Adjusting the mixer rotation speed
3.4 Pivoting the hopper discharge chute
3.5 Inversion of the front tool
3.6 Vertical adjustment of the reel
3.7 Horizontal adjustment of the reel
3.8 Transverse adjustment of the AUTO-CONTOUR cut
Chapter 4 Low pressure hydraulics
4.1 Low pressure hydraulics control plan
4.2 Pressure limiter
4.3 Low pressure hydraulic solenoid valves 3/2 distributor for the mixer clutches, the hopper drain auger and the front tool
4.4 Control of the 3-D cleaning box Pendulum box with 4/3 distributor and hydraulic cylinder
4.5 Front tool drive Hydraulic cylinder with rotating passage
Chapter 5 Front-end tools
5.1 Cut folding control plan
5.2 Control plan for folding the corn header / adjustment of the picking plates
5.3 Folding the 6/2 distributor cup with stop block
5.4 Folding the corn header / adjusting the header plates Valve block
5.5 Rake-up control plan – Hydraulic drive system
Chapter 6 Hydrostatic Drive
6.1 LINDE advancement hydraulics control plan
6.2 Pump unit
6.3 Servo control valve
6.4 Hydrostatic drive multifunction valve
6.5 Constant motor of hydrostatic drive
6.6 4-wheel drive drive
6.7 Maintenance
Chapter 7 Cleaning the Rotary Screen
7.1 Rotary screen control plan
7.2 Rotary screen drive
Keyword index
0293 813.2

00 0293 814 2.pdf:

MEGA 370 – 350 From machine number 845 00387, 835 00361 – Technical systems, Electrical system
Power plant
Pinout of modules
A6 air conditioning automation module:
A7 cabin fan rotation speed adjustment module:
AUTOCONTOUR module (CAC) A8: ref. 011 015.x
Contour A8 module: ref. 011 026.x
AUTOPILOT A9 module:
A12 rotation speed safety module:
A15 electronic engine control module:
Engine adaptation module (ADM) A17:
Quantity meter module A21:
A26 spreading plate adjustment module:
Multifunction lever module A52:
Overview of fuses:
Electrical plan 01a-50a
1a Main voltage supply, diesel engine starter
2a Starting the diesel engine, adjusting the rotation speed of the diesel engine
3a Diesel engine safety
4a Road driving control, circuit breaker valve
5a On-board informant
7a Mixer control
8a Beater variator
10a Fan variator
12a Adjustment of the spreading plate, flow control
14a Pivoting of the hopper discharge chute
15a Grain hopper emptying
17a Front tool drive
19a Reel variator
19b Rake-up – Adjustment of rotation speed, hydraulic oil temperature safety
20a Raising / lowering of the front tool, transverse adjustment
21a Adjusting the reel
23a Folding the cup
24a AUTOCONTOUR (CAC)
24b OUTLINE
25a Safety of the rotation regime
26a Machine safety
27a Quantimeter
28a AUTOPILOT
29a 4-wheel drive drive
30a Hopper filling indicator / Rotating beacon
31a Flashing device
32a Main lighting switch, position light
33a Low beam, switching of lights
34a Work lighting
35a Lighting of the grain hopper, the cleaning box, the waste return, reverse warning sound, brake light
36a Interior lighting, instrument lighting
37a Windshield wiper
38a Compressor, cabin fan
38b Air conditioning automation
39a Air seat compressor
40a Additional sockets
50a Electric mirror adjustment
Component coordination scheme
Keyword index
0293 814.2

00 0299 ​​506 2.pdf:

Technical systems – Hydraulic system, MEGA 360 – 350, up to machine number 845 00386, 835 00360
Chapter 1 General hydraulics
1.1 General plan of hydraulic controls up to machine number 835 00146, 845 00123
1.2 Oil tank, oil specification, filling quantity, oil change, oil filter, oil pressure
1.3 Hydraulic pumps up to machine number 835 00146, 845 00123
Chapter 2 Steering hydraulics
2.1 Hydraulic steering control plan without AUTOPILOT
2.2 Control plan with AUTOPILOT
2.3 Steering valve block
2.4 Function of neutral steering
2.5 Management check
2.6 AUTOPILOT left/right solenoid valve
2.7 Checking the AUTOPILOT system
Chapter 3 Operating Hydraulics
3.1 Operating hydraulicntrol plan
3.2 Pressure limiter of the operating hydraulic system
3.3 Raising/lowering thont tool 3/3 distributor
3.4 Unfolding/folding the grain hopper chute Distributor 4/3
3.5 Vertical adjustment of the 3/3 distributor reel
3.6 Inversion of the front tool (hydraulic) 3/2 distributor
3.7 Transverse adjustment of the AUTO-CONTOUR cut 4/3 distributor, stop block
3.8 Horizontal adjustment of the reel 4/3 distributor, stop block
3.9 Adjusting the mixer speed 3/3 distributor (mechanical)
3.10 Checking the operating hydraulics
Chapter 4 Low pressure hydraulics
4.1 Low pressure hydraulic control plan
4.2 Pressure limiter
4.3 Low pressure hydraulic solenoid valves 3/2 distributor for the mixer clutches, the hopper drain auger and the front tool
4.4 Control of the 3-D cleaning box Pendulum box with 4/3 distributor and hydraulic cylinder
4.5 Front tool drive Hydraulic cylinder with rotating passage
Chapter 5 Front-end tools
5.1 Cutting folding control plan
5.2 Control plan for folding the corn header / adjustment of the picking plates
5.3 Folding the 6/2 distributor cup with stop block
5.4 Folding the corn header / adjusting the header plates Valve block
Chapter 6 Hydrostatic Drive
6.1 LINDE forward hydraulics control plan
6.2 HPV 105 pump unit
6.3 Servo control valve
6.4 Hydrostatic drive multifunction valve
6.5 Constant motor of the hydrostatic drive Motor unit HMF 105
6.6 4-wheel drive Valve block
6.7 Maintenance
Chapter 7 Cleaning the Rotary Screen
7.1 Rotary screen control plan
7.2 Rotary screen drive
Component coordination scheme
Component coordination scheme
Keyword index
0299 506.2

00 0299 ​​507 2.pdf:

Technical systems Electrical system MEGA 360 – 350
Construction of electrical plans
Power plant
Module pinout
A6 air conditioning automation module:
Cabin fan rotation speed adjustment module A 7:
AUTOCONTOUR module (CAC) A8: spare parts reference: 011 015.x
Contour A8 module: spare parts refer: 011 026.x
AUTOPILOT A9 module:
A12 rotation speed safety module:
A15 electronic engine con module:
Engine adaptation module (ADM) A 17:
Quantity meter module A21:
A26 spreading plate adjustment module:
Order plans 01a – 50a
1a Main voltage supply, diesel engine starter
2a Starting the diesel engine, adjusting the rotation speed of the diesel engine
3a Diesel engine safety
4a Road driving command
5a On-board informant
7a Mixer control up to machine number 835 00146, 845 00123
7b Mixer control from machine number 835 00147, 845 00124
10a Fan variator
12a Adjustment of the spreading plate, flow control
14a Pivoting of the hopper discharge chute
15a Grain hopper emptying
17a Front implement drive, reverse drive (electric)
17b Front attachment drive, reversing drive (hydraulic) up to machine number 835 00146, 845 00123
17c Front attachment drive, reversing drive (hydraulic) from machine number 835 00147, 845 00124
19a Reel variator
20a Raising / lowering of the front tool, transverse adjustment
21a Adjusting the reel
21b Folding the corn header / adjusting the header plates
23a Folding the cup
24a AUTOCONTOUR (CAC)
24b OUTLINE
25a Safety of the rotation regime
26a Machine safety up to machine number 835 00146, 845 00123
26b Machine safety from machine number 835 00147, 845 00124
27a Quantimeter
28a AUTOPILOT
29a 4-wheel drive drive
30a Hopper filling indicator / Rotating beacon
31a Flashing device
32a Main lighting switch, position light
33a Low beam, switching of lights
34a Work lighting up to machine number 835 00146, 845 00123
34b Work lighting from machine number 835 00147, 845 00124
35a Lighting of the grain hopper, the cleaning box, the waste return, reverse horn, brake light
36a Interior lighting, instrument lighting
37a Windshield wiper
38a Compressor, cabin fan
38b Air conditioning automation
39a Air seat compressor
40a Additional sockets
50a Electric mirror adjustment
Component coordination scheme
Keyword index
0299 507.2