Claas Nexos 250 Vl – 210 Vl Stage 3B (A46) Tractors Repair Manual ES

File List:

00 1164 669 1.pdf
00 1178 790 X.pdf

00 1164 669 1.pdf:

NEXOS VE 240/230/220/210NEXOS VL 250/240/230/220/210NEXOS F 250/240/230/220/210
CCN (CLAAS COMPONENT NUMBER)
Introduction
General information
Using this repair manual
Validity of the repair manual
General repair instructions
Technical characteristics
Cause of damage
Interchange parts
Diesel engine
Generator
Welding work
Drive belt/drive chains
Conical ring assemblies
Self-locking screws with microencapsulated glue
Thread braking
Tightening ring bearing
Tightening sleeve bearing
Threaded fittings with cutting ring in hydraulic lines
Threaded fittings with progressive ring in hydraulic lines
Biconical threaded fittings in hydraulic conduits
Hydraulic hoses
Hose route
Tips for an economical repair
Tightening torques
Tightening torques for metric threads according to standard NF E25-030-1 2007-12-01
Tightening torques for hydraulic fittings CLAAS standard CN 020 225
Tightening torques for hydraulic threaded fittings and air conditioning threaded fittings with sealing cone and O-ring DIN 3865
Tightening torques for hydraulic threaded fittings DIN 3901
Tightening torques for adjustable hydraulic threaded fittings ISO 6149-2/ISO 11926-2 (3)
Tightening torques for pivoting hydraulic threaded fittings
Tightening torques for hollow screws DIN 7643
Technical data
Lubricants
01 Engine
0102 Complete component
Introduction
General observations
complete engine
Technical characteristics
special tool
Preliminary operations
Disassembly
Engine to frame coupling
Work preparation
General characteristics
Tightening torques
Engine disassembly
Technical characteristics
Preliminary operations
Disassembly
Cylinder head disassembly
Engine mounting
Technical characteristics
Mounting
0110 Engine casing
Technical characteristics
Preliminary operations
Disassembly
Mounting
Timing Gear Train Case
Technical characteristics
Work preparation:
Disassembly
Mounting
Flywheel cover
Technical characteristics
Work preparation:
Disassembly
Mounting
Cylinder block repair
Dimensional characteristics
Checks and measurements
Checking the contact surface of the cylinder head on the cylinder block
0115 Engine propulsion
Crankshaft
Technical characteristics
Dimensional characteristics
Tolerances
special tool
Preliminary operations
Disassembly
Measuring the journals and journals
Crankshaft journals and hands – Measured values
Replacing the crankshaft front sprocket
Mounting
Mounting the bearing half-shells
Control of lateral play
Rear bearing seal assembly
Timing case assembly
Connecting rod-piston assembly
Technical characteristics
Dimensional characteristics
special tool
Disassembly
Checking the piston
Shaft and piston pairing
Segments
Checking the segments
Control of the cranks
Torsion check
Bending check
Assembly of the connecting rod-piston assembly. Connecting rod-piston coupling
Assembly of the segments
Assembly of the connecting rod and piston assembly in the cylinder
Installing the connecting rod caps
Piston protrusion measurement
Balancer
Technical characteristics
special tool
Disassembly
Mounting
0120 Cylinder head / valves / distributor wheel
Technical characteristics
Preliminary operations
Disassembly
Leakage control
Checking the contact surface of the cylinder head
Checking the cylinder head bearing surface
Mounting
Dimensional characteristics
special tool
Disassembly
Stripping, checking and grinding of valves
valve guide
Checking the clearance between the stem and the valve guide. Centering check
Replacing valve guides
Valve guide reaming
Valve seats
Rectification of valve seats
Replacing valve seats
Checking valve contraction
Checking the valve springs
Mounting
Rocker cover
Technical characteristics
Preliminary operations
Disassembly
Mounting
final assembly
Rocker ramp
Technical characteristics
Dimensional characteristics
special tool
Preliminary operations
Disassembly
Mounting
final assembly
Camshaft
Technical characteristics
Dimensional characteristics
special tool
Disassembly
Checking Cam Lift and Shaft Bearing Alignment
Mounting
Replacing the rings
Mounting of the pushers
Synchronization
Technical characteristics
special tool
0125 Fuel/injection system
main fuel tank
Preliminary operations
Disassembly
Auxiliary fuel tank
Disassembly
Low pressure fuel lines
Technical characteristics
Fittings
Disassembly
Mounting
Fuel filter and prefilter
Technical characteristics
Preliminary operations
Disassembly
Mounting
Fuel lines from the high pressure pump to the common rail
Technical characteristics
Preliminary operations
Disassembly
Mounting
high pressure pump
Technical characteristics
special tool
Preliminary operations
Disassembly
Mounting
common ramp
Technical characteristics
Preliminary operations
Disassembly
Mounting
final assembly
Injectors
Technical characteristics
Preliminary operations
Disassembly
Mounting
final assembly
fuel cooler
Disassembly
0130 Lubricating oil system
Engine oil filter
Technical characteristics
Preliminary operations
Disassembly
Mounting
Oil pump
Technical characteristics
Preliminary operations
Disassembly
Mounting
Engine oil heat exchanger
Technical characteristics
Preliminary operations
Disassembly
Mounting
final assembly
Blow-by (Recirculation of oil vapors)
Technical characteristics
Preliminary operations
Disassembly
Mounting
0135 Cooling system
Radiator
Preliminary operations
Disassembly
Drive belts
Main drive belt
Preliminary operations
Disassembly
Mounting
Checking the tension of the main drive belt
Air conditioning compressor drive belt
Preliminary operations
Disassembly
Mounting
final assembly
Ventilation
Preliminary operations
Disassembly
Mounting
Water Pump
Technical characteristics
Preliminary operations
Disassembly
Mounting
Thermostat
Technical characteristics
Preliminary operations
Disassembly
Mounting
0140 Exhaust gas system
Exhaust pipe
Disassembly of the vertical exhaust pipe
Preliminary operations
Disassembly
Disassembly of the horizontal exhaust pipe
Preliminary operations
Turbocharger
Technical characteristics
Preliminary operations
Disassembly
Mounting
Manifold
Technical characteristics
Preliminary operations
Disassembly
Mounting
0145 Air suction
Air filter
Preliminary operations
Disassembly
Intake manifold
Technical characteristics
Preliminary operations
Disassembly
Mounting
final assembly
0150 Engine coupled parts
Alternator
Technical characteristics
Preliminary operations
Disassembly
Mounting
Starting motor
Preliminary operations
Disassembly
0155 Engine adjustment
Engine Management Module ECM
Technical characteristics
Preliminary operations
Disassembly
Mounting
engine wiring
Technical characteristics
Disassembly
Mounting
Glow plugs
Technical characteristics
Preliminary operations
Disassembly
Mounting
final assembly
0165 Exhaust gas aftertreatment
exhaust filter
Technical characteristics
Preliminary operations
Disassembly
Exhaust filter holder
Disassembly
Mounting
EGR valve
Technical characteristics
Preliminary operations
Disassembly
Mounting
02 Gears / clutch / cardan shaft
0202 Complete component
Special transmission tools
Mechanical inverter 12/12 and 24/24
24/24 Mechanical Inverter and Duplicator
Mechanical reverser and hydraulic duplicator 24/24
Hydraulic duplicator 24/24 and 24/12
Hydraulic reverser 24/12
Reducer casing
Final reduction standard version
Final reduction reinforced version
Hydraulic Control Front Axle Clutch
Front axle hydraulic clutch
Tightening, sealing and greasing torques
Application of lubricants and sealing products
Joint sealing products
Thread braking
Fixing adhesive
Grease during assembly
Greasing the gearbox input shaft and power take-off shaft
Front axle clutch housing with hydraulic control
Front axle clutch housing with mechanical control
Transmission clutch housing 12/12
24/24 Transmission Clutch Housing with Mechanical Control Duplicator
24/24 Transmission Clutch Housing with Hydraulic Control Duplicator
Transmission clutch housing 24/12
Reducer casing
Standard final reduction
Reinforced final reduction
Narrow final reduction
Short final reduction
Super short final reduction (892 mm)
Brake control group (valid for all models)
Internal gearbox control
External reducer control
Bottom and top covers
Assembly Features
All transmission models
Transmission 12/12
24/24 transmission with mechanical duplicator
24/24 transmission with hydraulic doubler
Transmission 12/24
Separation of engine and clutch housing with a fixed front axle
special tool
Preliminary operations
Transmission oil drain
Disassembly of the ducts
Disassembly of the first duct
Disassembly of the second duct
Separation of engine and clutch housing
Installing the cart under the tractor
Front axle immobilization
Removal of the fixing screws
Separation of the elements
Separation of engine and clutch housing with a suspended front axle
special tool
Preliminary operations
Transmission oil drain
Disassembly of the ducts
Disassembly of the first duct
Disassembly of the second duct
Separation of engine and clutch housing
Removal of the fixing screws
Separation of the elements
Top covers and riser
Technical characteristics
Work preparation:
Disassembly
Mounting
0215 Mechanical clutch
clutch adjustment
11 inch clutch
Adjustment
12 inch clutch
Adjustment
Clutch for REVERSHIFT transmission with mechanical clutch rear PTO
Adjustment
Transmissions with hydraulic duplicator – Clutch shaft
Replacing the Teflon gaskets. Exploded view
Substitution
Special tools
Transmission 12/24
24/24 transmission with hydraulic doubler
24/12 and 24/24 transmissions with hydraulic doubler
Transmission 12/24
24/24 transmission with hydraulic doubler
24/12 and 24/24 transmissions with hydraulic doubler
Air Compressor – Transmission 24/12
Exploded view
Disassembly
Mounting
0218 Clutch control/operation
Clutch and shuttle controls – Transmission 12/12
Mechanical inverter without duplicator – Exploded view
Disassembly
Mounting
Clutch and shuttle controls. 24/24 transmission (mechanical reverser and doubler)
Technical characteristics
Work preparation:
Disassembly
Mounting
Axial play adjustment
Clutch and shuttle controls – 24/24 transmission (Mechanical shuttle and hydraulic doubler)
Mechanical reverser and hydraulic duplicator – Exploded view
Disassembly
Mounting
Upper shaft axial play adjustment
Inverter shaft axial play adjustment
Clutch and shuttle controls. Transmission 12/24. hydraulic control power take off
Technical characteristics
Work preparation:
Disassembly
Mounting
Upper shaft axial play adjustment
Inverter shaft axial play adjustment
Clutch and shuttle controls. Transmission 12/24. mechanical control power take-off
Technical characteristics
Work preparation:
Preliminary operation
Disassembly
Mounting
Upper shaft axial play adjustment
Inverter shaft axial play adjustment
0220 Mechanical investment
Controls – Mechanical inverter
Exploded view
Disassembly
Transmission 12/24
Mounting
Transmission 12/24
Synchro reverser idler gear
Exploded view
Disassembly
Mounting
0222 Hydraulic inversion
Hydraulic reverser
Exploded view
Disassembly
Mounting
Game adjustment
Disc pack wear
idler sprocket
Exploded view
Disassembly
Mounting
0228 Reversing command/drive
Inverter controls
Mechanical inverter adjustment
Adjustment
0230 Mechanical gear
Input shaft – Transmission with mechanical shuttle
Technical characteristics
Disassembly
Mounting
Input shaft – Transmission with hydraulic shuttle
Exploded view
Disassembly
Mounting
Primary shaft – Speeds – Transmissions with mechanical shuttle
Exploded view
Disassembly
Mounting
Primary shaft – Speeds – Transmission 24/12
Exploded view
Disassembly
Mounting
Determination of axial clearance
Primary shaft – Ranges
Exploded view
Disassembly
Mounting
Secondary axis – Ranges
Exploded view
Disassembly
Mounting
Primary shaft covers
Transmission 12/12 – Section
24/24 transmission with inverter and mechanical duplicator – Section
24/24 transmission with mechanical shuttle and hydraulic doubler – Section
Transmission 12/24 – Section
Secondary Axle – Speeds
Technical characteristics
Disassembly
Mounting
Secondary shaft – Axial play measurement
mechanical duplicator
Exploded view
Disassembly
Mounting
0234 Load Switching Gear
hydraulic duplicator
Exploded view
Disassembly
Mounting
Disc pack wear
0238 Gearbox control/drive
External controls
Exploded view
Disassembly
Mounting
Internal controls
Transmission 12/12 and 24/24 – Exploded view
Internal controls – Transmission 24/12
Disassembly
Forward/reverse gear:
Mounting
0240 Rear axle housing
Trumpet and final reductions standard version
Exploded view
Disassembly
Mounting
Axial play adjustment
Trumpet and final reductions reinforced version 506 UP 6/1
Exploded view
Disassembly
Mounting
Preload of tapered roller bearings.
Trumpet and short version final reductions (972 mm)
Exploded view
Disassembly
Mounting
Preload of tapered roller bearings
Trumpet and final reductions of super short version (872 mm)
Exploded view
Disassembly
Mounting
Preload of tapered roller bearings
0242 Differential
Differential
Exploded view
Disassembly
Mounting
Differential lock control
Exploded view
Disassembly
Mounting
0248 Rear axle control/drive
Transmission Sensors – Exploded View
Location
Sensors/transmissions applicability
Disassembly
Description
Mounting
0250 Mechanical drive of the front axle
Hydraulic Control Front Axle Clutch
Exploded view
Disassembly
Mounting
0252 Electrohydraulic drive of the front axle
Front axle hydraulic clutch
Exploded view
Disassembly
Mounting
0255 Cooling system gear box
oil cooler
Disassembly
0260 Cardan shaft
Fixed front axle drive shaft
Disassembly
Suspended front axle drive shaft
Disassembly
03 Chassis
0310 Axle
Recommendations – Maintenance and repair
tree joints
Adjustment shims
Bearings
Plugs and rivets
Plastic caps and protections
Slotted Safety Pins
Adhesives and sealing products
Oil drain
Cleaning
Disc ends and special tools
Use of lubricants
0320 Steering axle
Tightening torques, lubricants and sealing products (two-wheel drive)
Joint sealing products
Application of lubricants and sealing products
Main dimensions (mm)
Adhesives and tightening torques
Steering cylinder (two-wheel drive)
Exploded view
Disassembly
Mounting
Repair of steering cylinders
Exploded view
Disassembly of the steering cylinder
Steering cylinder assembly
wheel hub
Exploded view
Disassembly
Mounting
Preliminary operations
Wheel hub support
Exploded view
Disassembly
Mounting
Preliminary operations
shaft body
Exploded view
Disassembly
Preliminary operations
Mounting
Pinch and rotation angle
Exploded view
Pinch Adjustment
Turning angle adjustment
0325 Front drive steering axle
Torque, lubricants and sealing products (four-wheel drive)
Joint sealing products
Thread braking
Fixing adhesive
Application of lubricants and sealing products
Technical characteristics of the four-wheel drive bridge. Nexus «F»
Main dimensions (mm)
Adhesives and tightening torques
Technical characteristics of the four-wheel drive front axle. «VE» Links
Main dimensions (mm)
Adhesives and tightening torques
Technical characteristics of the four-wheel drive bridge. «VL» Nexus
Main dimensions (mm)
Adhesives and tightening torques
Features of Limited Displacement Differential Discs
Steering cylinder • Links «F», «VE», «VL»
Exploded view
Disassembly of the steering cylinder
Steering cylinder assembly
Epicyclic reduction. Nexus «F»
Exploded view
Disassembly of the epicyclic reduction
Mounting the epicyclic reduction
Epicyclic reduction. «VE» Links
Exploded view
Disassembly
Preliminary operations
Mounting
Epicyclic reduction. «VL» Nexus
Exploded view
Disassembly
Mounting
b Exploded view
Disassembling the wheel hub «F», «VL»
Preliminary operations
Preliminary operations
Wheel hub assembly • Nexos «F», «VL»
Wheel hub • Nexos «VE»
Exploded view
Disassembly
Mounting
Board. Bearing assembly. Support • Nexus «F»
Exploded view
Disassembly
Mounting
Disk • Links «F», «VL»
Exploded view
Disassembly
Mounting
Disk • Nexus «VE»
Exploded view
Disassembly
Mounting
Differential case • Nexos «F», «VL»
Exploded view
Disassembly
Mounting
Assembly with new bearing
Alternative procedure after adjusting the tooth clearance
Checking the contact mark of the differential teeth
Differential case • Nexos «VE»
Exploded view
Disassembly
Preliminary operations
Mounting
Tooth gap clearance adjustment
If the bearings have not been replaced
ernative procedure after adssembly
Checking the contact mark of the differential teeth
Differential • Links «F», «VL»
Exploded view
Differential disassembly • Nexos «F», «VL»
Preliminary operations
Differential assembly • Nexos «F», «VL»
Additional operation in Nexos «F»
Differential • “VE” links
Exploded view
Differential disassembly • Nexos «VE»
Preliminary operations
Mounting
attack pinion
Special tools
Exploded view
Disassembly of the drive pinion
Preliminary operations
Drive pinion assembly
Operation to be carried out in Nexos «F», «VL»
Operation that must be carried out in Nexos «VE»
If the bearings have not been replaced
If the bearings have been replaced
Alternative procedure. «VE» Links
Alternative procedure
Front axle body • Links «F», «VL»
Special toolse front axle body
Front axle body assembly
Front axle bxploded view
Disassembly
Preliminary operations
Mounting
Pinch and rotation angle
Exploded view
Pinch Adjustment
Turning angle adjustment
0325 Front drive steering axle
Suspended front axle
Preliminary operations
Disassembly
Mounting
Position sensor link
Preliminary operations
Disassembly
Adjustment
Mounting
Suspended front axle guides
Preliminary operations
Disassembly
Mounting
Front axle suspension cylinders
Preliminary operations
Disassembly
Mounting
Suspended front axle position sensor
Exploded view
Preliminary operations
Disassembly
Mounting
Suspended front axle articulated support
Preliminary operations
Disassembly
Mounting
Suspended front axle articulated support bearing
Exploded view
Mounting
Hydraulic suspension module
Preliminary operations
Disassembly
Mounting
Front axle suspension module
Preliminary operations
Disassembly
Mounting
Front axle suspension calibration
Front axle suspension calibration button
Front axle suspension calibration procedure
Preliminary operations
Calibration
04 Brake
0405 Service brake
Assembly Features
Mechanical control brake
Hydraulic brake control – Tightening torques
brake master cylinders
Disassembly
Receiver cylinder
Exploded view
Disassembly
Mounting
Braking system bleeding
Technical characteristics
Work preparation:
Braking system bleeding
0415 Parking brake
Parking break
Exploded view
Preliminary operations
Disassembly
Mounting
On each side of the transmission case
Controller adjustment
Controller adjustment method
0425 Hydraulic Trailer Brake
Hydraulic Trailer Brake
Disassembly
05 Address
0505 Address
steering box
Disassembly
Steering angle sensor
Technical characteristics
Work preparation:
special tool
Disassembly
Mounting
06 Lifting device
0605 Rear linkage
Characteristics
Product identification
Description
Main elements of the elevator
Technical characteristics
Main dimensions
Benefits
Settings
Sensitivity adjustment valve
Position control lever
Effort control lever
Effort return bar adjustment
Adjustment of the position sensor at the limit switch
Shock valve pressure adjustment
Preliminary operations
special tool
Adjustment
Reaction spring assembly
Internal push bar
Lifting arm and cylinder
Exploded view
Mounting
Rear linkage control linkage
Exploded view
Mounting
Rear linkage main control
Disassembly
Mounting
Rear linkage plastic ring
Exploded view
Preliminary operations
Position control lever ring
Disassembly
Mounting
Effort control lever ring
Disassembly
Mounting
Effort and position control control linkage
Exploded view
Disassembly
Mounting
Rear hydraulic linkage distributor
Exploded view
Preliminary operations
Disassembly
Solenoid valves
Retention valve
pressure balance
Rear linkage shock valve
Mounting
08 Drives
0802 Rear PTO
Special tools
rear power take off
Tightening torques, lubricants and sealing products
Mechanical control PTO – 12/12 and 24/24 transmissions
Contactors
Independent power take-off (540/540E – 540/1000)
Independent power take-off (540/540E – 540/1000) and power take-off proportional to the forward speed
Hydraulic Control PTO – Transmission 24/12
Contactors
Independent power take-off (540/540E – 540/1000)
Independent power take-off (540/540E – 540/1000) and power take-off proportional to the forward speed
Cover and clutch
Exploded view
Disassembly
Mounting
Rear PTO clutch
Disc pack wear
Mechanical control of the rear power take-off
Technical characteristics
Work preparation:
Disassembly
Mounting
Rear power take-off control
Technical characteristics
Disassembly
Only for 24/12 broadcasts.
Mounting
Only for transmission 24/12
All transmission types
Only for transmission 24/12
All transmission types
input tree
Technical characteristics
Disassembly
Only without power take-off
All types of power take-off
Mounting
Only without power take-off proportional to the forward speed
All types of power take-off
Drive shaft
Technical characteristics
Disassembly
Mounting
PTO Brake – Transmission 24/12
Technical characteristics
Disassembly
Mounting
PTO proportional to forward speed
Hydraulic control power take-off. Technical characteristics
Mechanical control power take-off. Technical characteristics
Disassembly
Mounting
PTO operation proportional to ground speed
Rear PTO sensors
Location
09 Hydraulic
0915 Hydraulic pipes
Hydraulic oil filters
Disassembly
0920 Valves
Auxiliary distributors and levers
Auxiliary distributors
pressure limiter
Exploded view
Preliminary operations
Disassembly
Cleaning
Mounting
Rear distributor lock
Exploded view
Preliminary operations
Disassembly
Mounting
10 Install. electrical/electronic
1005 Power supply
Disassembly
Battery separator switch
«ON» position
«OFF» position
Removing the battery disconnect
1035 Multifunctional handle/lever
Elevator control pan Disassembly
12 Driver’s cab/platform
1210 Cabin
Lever coverings
Disassembly
Removing thetrol panel covering on the right side
Removing the control panel trim on the left side
rear wiper
Disassembly
Cabin support
Work preparation:
Front cabin support fixing
Rear cabin support fixing
Full cabin
special tool
Disassembly
1240 Air conditioning equipment
Air-conditioning system
Compressor
Preliminary operations
Compressor disassembly
80 Attached parts, machine casing
8025 Coverings / hoods
Engine cover
Disassembly
Hood side panels
Disassembly

00 1178 790 X.pdf:

Repair manual
CCN (CLAAS COMPONENT NUMBER)
Introduction
General information
Using this repair manual
Validity of this repair manual
General repair instructions
Technical characteristics
Cause of damage
Interchange parts
Diesel engine
Generator
Welding work
Drive belt/drive chains
Conical ring assemblies
Self-locking screws with microencapsulated glue
Thread braking
Tightening ring bearing
Tightening sleeve bearing
Threaded fittings with cutting ring in hydraulic lines
Threaded fittings with progressive ring in hydraulic lines
Biconical threaded fittings in hydraulic conduits
Hydraulic hoses
Hose route
Tips for an economical repair
Tightening torques
Tightening torques for metric threads according to factory standard CN02-0220 2002-09-26
Tightening torque for screws
Tightening torque for DRH self-locking nuts
Tightening torque for Nylstop self-locking nuts
Tightening torques for hydraulic fittings CLAAS standard CN 02 0225
Tightening torques for hydraulic threaded fittings and air conditioning threaded fittings with sealing cone and O-ring DIN 3865
Tightening torques for hydraulic threaded fittings DIN 3901
Tightening torques for adjustable hydraulic threaded fittings ISO 6149-2/ISO 11926-2 (3)
Tightening torques for pivoting hydraulic threaded fittings
Tightening torques for quick connect cartridges
Tightening torques for hydraulic threaded wall gland fittings DIN 8434
Tightening torques for hollow screws DIN 7643
Technical data
Lubricants
01 Engine
0102 Complete component
Introduction
General observations
0110 Engine casing
Timing Gear Train Case
Technical characteristics
Work preparation:
special tool
Disassembly
Timing case assembly
Lid assembly
Front bearing seal assembly
Technical characteristics
Disassembly
Mounting
Flywheel cover
Technical characteristics
Work preparation:
special tool
Disassembly
Mounting
Disassembly of the rear bearing seal
Rear bearing seal assembly
0115 Engine propulsion
Crankshaft
Technical characteristics
Dimensional characteristics
Disassembly
Measuring the journals and journals
Crankshaft journals and hands – Measured values
Replacing the crankshaft front sprocket
Mounting
Mounting the bearing half-shells
Control of lateral play
crankshaft pulley
Technical characteristics
Connecting rod and piston assembly
Technical characteristics
Dimensional characteristics
special tool
Disassembly
Checking the piston
Shaft and piston pairing
Segments
Checking the segments
Control of the cranks
Torsion check
Bending check
Assembly of the connecting rod and piston assembly. Connecting rod and piston coupling
Assembly of the segments
Assembly of the connecting rod and piston assembly in the cylinder
Installing the connecting rod caps
Piston protrusion measurement
Balancer
Technical characteristics
special tool
Disassembly
Mounting
engine flywheel
Technical characteristics
0120 Cylinder head / valves / distributor wheel
Technical characteristics
Dimensional characteristics
Disassembly
Leakage control
Checking the cylinder head bearing surface
Checking the contact surface of the cylinder head (cylinder block)
Mounting
Dimensional characteristics
special tool
Disassembly
Cleaning and checking valves
Checking the clearance between the valve rods and the valve guide and centering the valves
Checking the valve springs
Checking and replacing valve guides
Checking valve guidance
Replacing valve guides
Valve guide reaming
Checking and replacing valve seats
Mounting
Checking valve contraction
Rocker cover
Technical characteristics