Claas Tucano 480-470 (840) Combines Operator Manual FR

File List:

00 0290 491 2.pdf
00 0291 840 3.pdf
00 0292 676 0.pdf
00 0294 818 9.pdf
00 0301 730 0.pdf

00 0290 491 2.pdf:

Contents
1 Introduction
1.1 General advice
1.1.1 Validity of the notice
2 Overview
2.1 Assembled parts / Machine casing
2.1.1 Access to the driving position and maintenance points
3 Security
3.1 General advice
3.1.1 Use in accordance with instructions
3.1.2 Clearly non-compliant use
3.1.3 Decommissioning and disposal
3.2 Warning pictograms
3.2.1 Separation
3.2.2 Deposit of harvested product / deposit of straw
4 Technical characteristics
4.1 TUCANO 450 – Type 840
4.1.1 General advice
4.1.2 Motor
4.1.3 Chassis
4.1.4 Chassis tire pressure
4.1.5 Chassis, track
4.1.6 Brake
4.1.7 Management
4.1.8 Electrical/electronic system
4.1.9 Cabin / driving position
4.1.10 Power supply organs
4.1.11 Threshing bodies
4.1.12 Separation
4.1.13 Cleaning
4.1.14 Grain recovery
4.1.15 Grain recovery, dimensions
4.1.16 Dimensions of assembly parts / machine casing
4.1.17 Weight of assembly parts / machine casing
5 Before first commissioning
5.1 General advice
5.1.1 General warnings Before initial commissioning
5.2 Attached parts / machine casing
5.2.1 Open/close the rotor drive side door
5.2.2 Using the rear ladder
10 Setting for work
10.1 General advice
10.1.1 General work warning advice
10.2 Power organs
10.2.1 Adjust the drive speed of the front tool, belt (R1)
10.2.2 Set the cutting angle of the V-feed channel (optional equipment) to the basic setting
12.1 General advice
12.1.1 General work warning advice
12.2 Power unit
12.2.1 Adjusting the cutting angle of the V feed channel (optional equipment)
12.3 Separation
12.3.1 Adjust the rotor speed
12.3.2 Pay attention to straw jam alarms behind the separation
12.3.3 Set separation flow control display
12.4 Deposit of harvested product / straw deposit
12.4.1 Commissioning the straw chopper (swivel the standard distributor to the crushing position)
12.4.2 Stopping the straw chopper (pivot the standard distributor to the windrowing position)
12.5 Grid Tables / Threshing Tables
12.5.1 Threshing table (TUCANO 450)
14 Maintenance
14.1 General advice
14.1.1 General warning advice Maintenance
14.2 Maintenance table
14.2.1 Maintenance frequencies
14.3 Lubricant table
14.3.1 Lubricants
14.4 Engine
14.4.1 Refueling the machine
14.4.2 Clean the filler grid of the additional fuel tank (additional equipment)
14.4.3 Replace the fuel filter (additional fuel tank, additional equipment)
14.4.4 Replace the fuel filter (CATERPILLAR C-9)
14.4.5 Bleed the air from the fuel system (CATERPILLAR C-9)
14.4.6 Check the oil level of the diesel engine (CATERPILLAR C-9)
14.4.7 Diesel engine, replace oil/oil filter (CATERPILLAR C-9)
14.5 Brake
14.5.1 Adjusting the foot brake
14.5.2 Checking the brake pads / brake shoes
14.5.3 Replacing brake pads / brake shoes
14.6 Drive belts / drive chains
14.6.1 General safety advice
14.6.2 Left side drive diagram TUCANO 450
14.6.3 Right side drive diagram TUCANO 450
14.6.4 Adjust the belt (R20)
14.6.5 Adjust the belt (R22)
14.6.6 Adjust the belt (R23)
14.6.7 Remove the belt (R24)
14.6.8 Install the belt (R24)
14.6.9 Adjust the belt (R24)
14.6.10 Adjust the belt (R25)
14.6.11 Remove the belt (R43)
14.6.12 Install the belt (R43)
14.6.13 Adjust the belt (R49)
14.6.14 Remove the belt (R50)
14.6.15 Fitting the belt (R50)
14.6.16 Adjust the belt (R50)
14.7 Separation
14.7.1 Check the rotor gearbox oil level
14.7.2 Drain the oil from the rotor gearbox
14.7.3 Pour oil into rotor gearbox
14.7.4 Clean the separation flow control sensor
14.7.5 Clean the rotor
15 Lubrication plan
15.1 Lubrication points
15.1.1 General warning tips lubrication scheme
15.1.2 Fats
15.1.3 Lubrication intervals
15.1.4 Lubrication points – 10 o’clock left side
15.1.5 Lubrication points – 10 o’clock right side
15.1.6 Lubrication points – 50 h left side
15.1.7 Lubrication points – 100 h left side
15.1.8 Lubrication points – 500 h left side
15.1.9 Lubrication points – 500 h right side
Alphabetical index

00 0291 840 3.pdf:

TUCANO 470 – 320
Contents
1 About this user manual
1.1 General information
1.1.1 General instructions
1.1.2 Validity of the notice
1.1.3 Use of the instructions
1.1.4 Symbols and instructions
1.1.5 Machine equipment
1.1.6 Technical characteristics
2 Security
2.1 Safety marking on the machine
2.1.1 Deposit of harvested product / straw deposit
2.1.2 Warning pictogram
3 Description of the machine
3.1 Overview and mode of operation
3.1.1 Engine overview
4 Controls and displays
4.1 Cabin / Driving position
4.1.1 Driving informant
4.2 Display / Management
4.2.1 Overview of the displacement indicator
5 Technical characteristics
5.1 TUCANO 470 / 450 / 440 / 430 / 340 / 320 – Types 840 / 839 / 838 / 834 / 832
5.1.1 Motor
5.1.2 Electrical system / electronic system
5.1.3 Assembly parts / ballast machine casing
6 Preparing the machine
6.1 Disconnect the machine and secure it
6.1.1 Stop and secure the machine
6.2 Loading the machine
6.2.1 Use slinging means
7.1 General information
7.1.1 General warning instructions
7.2 Deposit of harvested product / Deposit of straw
7.2.1 Adjust the speed of the straw chopper (TUCANO 450 / 440 / 430 / 340 / 320, left side drive)
Reduce the speed of the straw chopper
Increase the speed of the straw chopper
7.2.2 Overview of the straw chopper
7.2.3 Set the straw chopper to the windrowing position
7.2.4 Set the straw chopper to the chopping position
7.2.5 Adjust the inclination (Special Cut scatter deflector plate)
8 Incidents and remedies
8.1 General information
8.1.1 General warning instructions
8.2 Cabin / Driving position
8.2.1 Basic central electrical system
8.3 Electrical system / Electronics
8.3.1 Vehicle main fuse
8.3.2 Battery, mounting position
8.3.3 Starting assistance (12 V / 24 V)
Starting assistance (12 V / 24 V)
Start the diesel engine externally
9 Maintenance
9.1 General information
9.1.1 General warning instructions
9.1.2 Authorized fuels
9.1.3 Urea solution
Use of urea solution
Purity/Standard of nitrogen solution
Storage of urea solution in tanks/bins
Properties of urea solution at high/low outdoor temperatures
9.1.4 Welding work on the combine harvester
9.2 Operating consumables
9.2.1 Lubricants
9.3 Maintenance intervals
9.3.1 Every 10 operating hours or every day
9.3.2 Every 500 operating hours or every year
9.3.3 Every 1000 operating hours or every 2 years
9.3.4 Every 3 years
9.4 Engine
9.4.1 Clean around the diesel engine
9.4.2 Refill the machine with urea solution
9.4.3 Replace the urea solution filter
9.5 Orders
9.5.1 General warning instructions
9.5.2 Setting drives
9.5.3 Adjust the belt (R26)
9.5.4 Remove the belt (R27)
9.5.5 Adjust the belt (R27)
9.5.6 Remove the belt (R53)
9.5.7 Install the belt (R53)
9.5.8 Adjust the belt (R53)
9.6 Assembly parts, bodywork
9.6.1 Replace the dry air filter of the compressed air cleaning system
9.7 Lubrication plan
9.7.1 Lubrication points – 100 h left side
9.7.2 Lubrication points – 500 h left side

00 0292 676 0.pdf:

LEXION 770 – 620TUCANO 470 – 320
Contents
1 About this user manual
1.1 General information
1.1.1 Validity of the notice
1.1.2 Symbols and instructions
2 Controls and displays
2.1 Cabin / Driving position
2.1.1 CEBIS control panel
2.2 CEBIS display
2.2.1 CEBIS general advice
2.2.2 Overview of the displacement indicator
2.2.3 Overview of the displacement indicator
2.2.4 Overview of the harvest indicator
2.2.5 CRUISE PILOT crop indicator overview
2.2.6 CEBIS direct menu overview
2.2.7 Respect CEBIS error code information
Respect type of error code information
Respect the structure of error code information
Classify error code information
View alarm history
View active alarms
2.2.8 Message box symbols
2.2.9 CEBIS direct menu
2.2.10 HOTKEY direct menu
2.2.11 Quick access menu
2.2.12 Main menu
2.2.13 Front tool menu
2.2.14 Driving menu
2.2.15 AUTO PILOT menu
2.2.16 Machine settings menu
2.2.17 Harvested product settings menu
2.2.18 Counter Menu
2.2.19 Maintenance menu
2.2.20 CEBIS menu

00 0301 730 0.pdf:

IIIB diesel engines
Contents
1.1 Diesel engine
1.1.1 Connect the diesel engine
EN – Connect the diesel engine
No significant engine error recognized (DTC)
Engine Recognized Significant Error (DTC)