Claas V1350-V1050 Lexion Tucano (529) Combines Repair Manual FR

File List:

00 0291 774 0.pdf

00 0291 774 0.pdf:

VARIO 1200-1050
CERIO 1200-1050
Contents
Introduction
General informations
Use of the instructions
Validity of the notice
General repair tips
Technical specifications
Cause of damage
Spare parts
Diesel motor
Generator
Welding work
Drive belt/drive chains
Tension steel roller chains
Assemblies using conical ring
Heel pin assemblies
Self-locking screws with microencapsulated glue
Liquid screw brake
Clamp ring bearing
Clamp sleeve bearing
Screwed connections with cutting ring on hydraulic lines
Progressive ring screw connections on hydraulic lines
Bicone screw connections on hydraulic lines
Hydraulic flexible lines
Tips for an economical repair
Tightening torques
Tightening torques for metric coarse threads
Tightening torques for metric fine pitch threads
Tightening torques for hydraulic connections with cutting ring DIN 3861
Tightening torques for hydraulic screw connections and air conditioning screw connections with sealing cone and O-ring DIN 3865
Tightening torques for hydraulic threaded couplings DIN 3901
Tightening torques for hydraulic swivel threaded couplings ISO 6149-2 / ISO 11926-2 (3)
Tightening torques for hydraulic swivel screw connections
Tightening torques for hollow screws DIN 7643
Tightening torques for brake line screw connections
Tightening torques for tangent screw clamps
Tightening torques for spring-controlled tangent screw clamps
Tightening torques for tires
Technical characteristics
Lubricants
CCN explanation
CCN (CLAAS Component Number)
Electrical standard
Summary table
Hydraulic standard
Overview
CCN Index
Security
General informations
To respect
Marking of warning and danger instructions
General safety and accident prevention instructions
Deposit of harvested product / Deposit of straw
Exit the machine
Chopping device, combine harvester
Adjustment and maintenance work
Risk of injury from hydraulic fluids
Air conditioner
Pressure accumulator
First aid measures
Battery cut-off switch
Install the safety support of the supply channel
Place the machine on jack stands
Take the machine out of service
02 Transmission – Clutch – Cardan shaft
0230 Mechanical gearbox
Spur gear angle gearbox
Preparing for work
Special tool
Disassemble
To assemble
To set down
Rapeseed saw drive pump clutch
Preparing for work
Special tool
Disassemble
To assemble
To set down
Left side transfer case
Preparing for work
Special tool
Disassemble
To assemble
To set down
Right side transfer case
0260 Cardan shaft
Main drive cardan shaft
Preparing for work
Disassemble
To assemble
To set down
Gearbox drive cardan shaft
Preparing for work
Disassemble / Assemble
To set down
08 Orders
0800 Drive scheme
Training scheme
0814 Intermediate shaft control
Intermediate shaft
Preparing for work
Assembly tips
09 Hydraulic system
0900 Hydraulic system General
Damage to the hydraulic system
0915 Hydraulic circuit
Multiple coupling
0920 Valves
Distribution block, general
Special tool
Main distribution block
Assembly tips
10 Electrical system – Electronics
1012 Modules – Sensors
1035 Use / Multifunction control
20 Harvest feeding
2010 Cutting deck extension
Cutting apron table
To set down
Pressure accumulator (5015)
Reduce pressure
Hydraulic table adjustment cylinder (3049)
Preparing for work
To set down
Table position sensor (B070)
2015 Reel / Equalizer
Remove the left side reel
Install the left side reel
Remove the right side reel
Install the reel on the right side
Command Star
To set down
Control rollers
To set down
Reel hub star
To set down
Reel tooth tubes
To set down
Replace the special nut
Reel shaft bearing
Preparing for work
Remove the left reel shaft bearing
Install the left reel bearing
Remove the bearing on the right side of the reel shaft
Install the bearing on the right side of the reel shaft
Remove the reel shaft center bearing
Install the reel shaft center bearing
Reel support arm
Preparing for work
Remove the left side support arm
Install the left side support arm
Remove the right side support arm
Install the right side support arm
Remove the central support arm
Install the central support arm
Reel drive
Preparing for work
To set down
Reel horizontal adjustment sensor (B040)
Reel Vertical Position Sensor (B039)
Hydraulic reel drive motor (2012)
Preparing for work
To set down
Hydraulic cylinder for vertical adjustment of the reel
Preparing for work
Remove the exterior cylinders
Install the exterior cylinders
Remove the interior cylinders
Install the interior cylinders
Hydraulic cylinder for horizontal adjustment of the reel (3016)
Preparing for work
Assembly tips
Safety distance of the reel support arms
2030 Rapeseed equipment
Rapeseed saw
Rapeseed saw hydraulic oil tank (1011)
Generate depression
Special tool
Left side rapeseed saw distribution block
Assembly tips
Rape saw drive pressure limiter (7030)
Adjust the pressure
Special tool
Rapeseed saw drive pump (2022)
To set down
21 Power group
2140 Feed screw
Feed drum
Preparing for work
Assembly tips
To set down
Outer Feed Drum Bearing
Special tool
Assembly tips
Disassemble
To assemble
To set down
Feed drum center bearing
Preparing for work
To set down
Feed drum drive shaft
To set down
Feed Drum Fingers
Assembly tips
Adjusting the control shafts
Assembly tips
To set down
Adjustment shaft
Special tool
Assembly tips
To set down
Control tree
To set down
23 Reaper
2305 Cutting bar
Cutting bar, general
Knife drive cardan shaft
Preparing for work
Assembly tips
Planetary knife drive gear
Preparing for work
Special tool
Assembly tips
Disassemble
To assemble
To set down
26 Ground guidance
2605 Self-Contour
AUTO CONTOUR sensor
80 Assembly parts / Bodywork
8005 Chassis
Anti-grain projection sheets
Preparing for work
8010 Lock
Lockdown
8020 Balustrades / Safety devices
Protective hatch
Sliding protection