Claas VARIANT 465 460 365 360 RC RF (751) Baler Technical System DE

File List:

– 00 0288 124 3.pdf
– 00 0291 568 4.pdf
– 00 0294 120 1.pdf
– 00 0294 124 2.pdf

00 0288 124 3.pdf

Table of Content:
1 VARIANT 450VARIANT 460VARIANT 465VARIANT 470VARIANT 480VARIANT 485
2 Table of Contents
3 Introduction
3.1 General information
3.2 CCN declaration
4 CCN (CLAAS Component Number)
5 09 Hydraulics
5.1 0920 Valves
5.2 0980 Hydraulic circuit diagrams
6 10 Electrics / Electronics
6.1 1005 Power supply
6.2 1012 modules / sensors
6.3 1040 Yield measurement
6.4 1080 electrical circuit diagrams
6.5 1081 Connector overview
6.6 1085 Networks
7 21 feed unit
7.1 2125 Rotor
8 45 Press device
8.1 4500 Press device
9 46 Binding system
9.1 4610 Yarn binding
9.2 4615 Net binding / film binding
10 75 Central lubrication
10.1 7505 Container, pump
10.2 7515 Lubrication system / lines
11 92 Diagnosis
11.1 9210 error codes machine
12 Location of the components
12.1 Hydraulics
12.2 Electrics

00 0291 568 4.pdf

Table of Content:
1 VARIANT 360VARIANT 365VARIANT 380VARIANT 385
2 Table of Contents
3 Introduction
3.1 General information
3.2 Overview of machine
4 CCN Declaration
4.1 CCN (CLAAS Component Number)
5 CCN (CLAAS Component Number)
6 09 Hydraulics
6.1 0920 Valves
6.2 0980 Hydraulic circuit diagrams
7 10 Electrics / Electronics
7.1 1010 Central Electrics
7.2 1012 modules / sensors
7.3 1080 electrical circuit diagrams
8 21 feed unit
8.1 2125 Rotor
9 Location of components
9.1 Electrics

00 0294 120 1.pdf

Table of Content:
2 1 Total hydraulics
2.1 Hydraulic circuit diagram
3 2 Working hydraulics
3.1 Main valve block
3.2 Rotor coupling shut-off valve
3.3 Rotor shut-off clutch
3.4 Rotocut knife solenoid valve OFF – ON
4 3 Location of the components
4.1 Pick-up
4.2 Pressure filter, shut-off valve, main valve block I
4.3 Hydraulic circuit diagram rotor clutch, flat belt drive clutch
4.4 Valve block check valves, clamping arms

00 0294 124 2.pdf

Table of Content:
2 1 Introduction
2.1 Structure of the electrical documentation
3 2 Modules
3.1 Module representation
3.2 Module assignment
4 3 circuit diagrams
4.1 01a Main voltage supply VARIANT 360/385 Comfort
4.2 01b Main voltage supply VARIANT 360/385 Standard
4.3 06a CAN bus, power supply module VARIANT 360/ 385 Comfort
4.4 06b CAN bus, power supply module VARIANT 360/ 385 Standard
4.5 07a Rotocut VARIANT 360/ 385 Comfort
4.6 07b Rotocut VARIANT 360/ 385 Standard
4.7 10a pressing pressure control VARIANT 360/ 385 Comfort
4.8 10b Press pressure control VARIANT 360/ 385 Standard
4.9 11a Binding release VARIANT 360/ 385 Comfort
4.10 11b Binding release VARIANT 360/ 385 Standard
4.11 26a Machine monitoring VARIANT 360/ 385 Comfort
4.12 26b Machine monitoring VARIANT 360/ 385 Standard
4.13 27a Operating displays VARIANT 360/ 385 Comfort
4.14 27b Operating displays VARIANT 360/ 385 Standard
4.15 32a lighting VARIANT 360/ 385