Claas Vario 1380-1080 (823) Combines Technical System EN

File List:

00 0302 343 1.pdf
00 0302 565 2.pdf
00 0305 818 1.pdf
CLAAS HARNESS PARTS.pdf

00 0302 343 1.pdf:

PROFI CAM 3
Table of contents
General information
Marking of warnings and hazard prevention notes
First-aid measures
CCN explanation
CCN (CLAAS Component Number)
Electric system standard
Overview
Hydraulic system standard
Overview
CCN (CLAAS Component Number)
10 Electrical / Electronic equipment
1030 Board computer / Indicators
Camera system
Description of function
1097 Testing / Measuring / Adjusting
Testing / measuring / adjusting the PROFI CAM
Checking the fuse in the video channel select box (C102)
Testing the video camera connector (C055)
1098 Fault / remedy
Fault / remedy PROFI CAM
The video monitor (C101) shows no image or cannot be switched on (indicator light fails to light up)
Video monitor (C102) displays a blue image either permanently or temporarily
The video monitor image is blurred
Replacing the fuse in the video channel select box (C102)
Connection and connecting cable with video camera (C055)

00 0302 565 2.pdf:

Sensor system
Table of contents
CCN explanation
CCN (CLAAS Component Number)
Electric system standard
Overview
Hydraulic system standard
Overview
CCN (CLAAS Component Number)
Introduction
Safety rules
Safety and hazard information
10 Electrical / Electronic equipment
1097 Testing / Measuring / Adjusting
Test report of the angle sensor (0011780.x)
Application of test report
Required tools
Test report of the angle sensor (0011780.x)
Testing / Measuring / Adjusting of angle sensor (0011780.x)
1. Reason for test
2. Mechanical test of angle sensor
3. Electric test with CDS
4. Electric test with multimeter
5. Mechanical test of connecting cable
Completing the machine
Test report of position and speed sensors
Application of test report
Required tools
Sensor variants
Part numbers of speed sensors
Part number of position sensor
Test report of position and speed sensors
Testing / measuring / adjusting of position and speed sensors
1. Reason for test
2. Mechanical test
3. Electric test with CDS
4a. Installation dimensions
Check of installation dimension
Installation dimensions of gearbox speed sensor (0011 799.x) and cam speed sensor (0011 810.x)
Installation dimension of position sensor (0011 815.x)
4b. Installation position
Centring of sensor
Metal-free zone
5. Electric test with multimeter
Voltage measurement
Direction of rotation and speed sensor (0011 605.x)
Measured values table
6. Mechanical test of connecting cable
Completing the machine
Test report of the urea sensor (00 0773 207 x)
Application of test report
Required tools
Parts number of the urea sensor
Test report of the urea sensor
Testing / measuring / adjusting urea sensor
1. Reason for test
2. Mechanical test
3. Mechanical test of connecting cable
4. Electric test with multimeter
5. Component test with the CDS

00 0305 818 1.pdf:

Technical systems
Table of contents
Introduction
Notes on the manual
Validity of manual
Information about this Technical Systems Manual
Using the manual
Document structure based on subassemblies
Search and find
Directions
Identifying warnings
Hazard signs
Signal word
Safety rules
Safety signs and warnings
Requirement made on technical staff
Children in danger
Hazard areas of the machine
Instructors travelling along during fieldwork
Risk of injury from rotating shafts
Structural alterations of the machine
Optional equipment and spare parts
Control of running machine
Technical condition
Respecting technical limit values
Danger from machine parts that continue rotating
Keeping safety devices functional
Personal protective equipment
Wearing suitable clothing
Removing dirt and loose objects
Parking the machine safely
Unsuitable operating utilities
Safe handling of service fluids and auxiliary utilities
Environmental protection and disposal
Keeping the cab free of chemicals
Avoiding fires
Potentially fatal electric shock from overhead lines and lightning strike
Electric shock from electric system
Noise may damage your health
Pre-loaded machine parts
Liquids under pressure
Compressed air
Toxic exhaust gases
Hot surfaces
Safe access and leaving
Working only on the stopped machine
Hazards during repairs
Raised machine parts and loads
Danger from welding work
Checking and charging the battery
Preparations for cases of emergency
CCN explanation
CCN (CLAAS Component Number)
Electric system standard
Overview
Hydraulic system standard
Overview
CCN (CLAAS Component Number)
09 Hydraulic system
0920 Valves
Reel / table / intake auger adjustment control valve block
0980 Hydraulic circuit diagram
Front attachment hydraulics VARIO – type 823
Cutterbar V1080-V1380 (type 823) – SCM 01 – Reel drive
Cutterbar V1080-V1380 (type 823) – SCM 02 – Intake auger adjustment
Cutterbar V1080-V1380 (type 823) – SCM 03 – Cutterbar table adjustment
Cutterbar V1080-V1380 (type 823) – SCM 04 – Reel adjustment
10 Electrical / Electronic equipment
1012 Modules / sensors
Module A130 – Front attachment – type 823 VARIO
Key to diagram
Key to diagram
Module A176 – Front attachment enhancement – type 823 VARIO
Key to diagram
Key to diagram
Module A219 – Front attachment lighting – type 823 VARIO
Key to diagram
Key to diagram
1015 Wiring harnesses
Multi-coupler
Front attachment multicoupler
Description of function
1080 Electrical circuit diagram
Front attachment circuit diagrams – VARIO cutterbar (type 823)
ATT 01 – Multi-coupler
Key to diagram
ATT 02 – Power supply of modules / CAN Bus
Key to diagram
ATT 03 – Reel
Key to diagram
ATT 04 – Intake auger
Key to diagram
ATT 05 – Table adjustment
Key to diagram
ATT 07 – AUTO CONTOUR
Key to diagram
ATT 08 – AUTO PILOT
Key to diagram
ATT 09 – Flashlights
Key to diagram
ATT 10 – Lighting
Key to diagram
ATT 11 – Overview of modules
Key to diagram
20 Crop feeding
2010 Cutterbar table
VARIO cutting table adjustment
Measured values table
Functional description of cutting table adjustment
Hydraulics: Cutterbar table adjustment
2015 Reel / Crop guard
Raise / lower reel, automatic reel height adjustment
Measured values table
Reel adjustment function description
Horizontal reel adjustment
Measured values table
Reel adjustment function description
21 Feeder unit
2140 Intake auger
Centre intake auger raise / lower
Measured values table
Functional description of intake auger adjustment
Position of components
Hydraulic system
2000 Pump / motor
3000 Hydraulic cylinders
4000 Restrictor / orifice plate
Electric system
A Terminal / modules
B Sensors
E Lighting
U Switches – External operation
X Connectors
Y Solenoid coils

CLAAS HARNESS PARTS.pdf:

CLAAS HARNESS PARTS
Table of contents
10 Electrical / Electronic equipment
1081 Overview of connectors
CLAAS HARNESS PARTS (CHP)