IMT Model 32027 Crane Parts and Specifications 99901210

Table of Content:

1 ELECTRONIC MANUALS
2 REVISIONS LIST
3 INTRODUCTION
4 SPECIFICATIONS
4.1 GENERAL SPECIFICATIONS
4.2 PERFORMANCE CHARACTERISTICS
4.3 POWER SOURCE
4.4 CYLINDER HOLDING VALVES
4.5 ROTATION SYSTEM
4.6 HYDRAULIC SYSTEM
4.7 SELECTED WEIGHTS OF ANCILLARY EQUIPMENT
4.8 CAPACITY CHART
4.9 GEOMETRIC CONFIGURATION
4.10 CRANE MOUNTED ON CHASSIS
4.11 MINIMUM CHASSIS SPECIFICATIONS
5 CRANE REFERENCE
5.1 MAJOR CRANE ASSEMBLIES
5.2 WELDMENT PART NUMBER LOCATIONS
5.3 GREASE ZERK LOCATIONS & LUBRICANT REQUIREMENTS
5.4 RECOMMENDED SPARE PARTS LIST
5.5 INSTALLATION
5.6 GENERAL
5.7 CRANE MOUNTING
5.8 HYDRAULIC INSTALLATION
6 PARTS
6.1 PARTS INFORMATION
6.2 CRANE IDENTIFICATION
6.3 CYLINDER IDENTIFICATION
6.4 WELDMENT IDENTIFICATION
6.5 ORDERING REPAIR PARTS
6.6 BASE & STABILIZER ASM (41714211-1)
6.7 BASE & STABILIZER ASM (41714211-2)
6.8 PWR OUT STABILIZER CYLINDER (3B144860)
6.9 PWR DN STABILIZER CYLINDER (3C145860)
6.10 AUX STABILIZER ASM (31706397)
6.11 AUX STABILIZER PWR DN CYLINDER (3B020860)
6.12 AUX STABILIZER PWR OUT CYLINDER (3B148860)
6.13 MAST ASM (41714189)
6.14 INNER BOOM ASM (41714190)
6.15 INNER BOOM CYLINDER (3D203970)
6.16 OUTER BOOM ASM (41714214)
6.17 OUTER BOOM CYLINDER (3C204970)
6.18 EXTENSION BOOM ASM (41714215)
6.19 EXTENSION BOOM CYLINDER (3C209970)
6.20 INSTALLATION KIT (93714217-1)
6.21 INSTALLATION KIT (93714217-2)
6.22 DECAL KIT (95714074)
6.23 HYDRAULIC KIT (91714213-1)
6.24 HYDRAULIC KIT (91714213-2)
6.25 HYDRAULIC KIT (91714213-3)
6.26 HYDRAULIC KIT (91714213-4)
6.27 HYDRAULIC KIT (91714213-5)
6.28 REMOTE CONTROL KIT (90714209)
6.29 CABLE ASM-JIC BOX (51712880)
6.30 CAPACITY ALERT KIT-3000 PSI (31711302)
6.31 FLOODLIGHT KIT (51709314)
6.32 ROTATION SPEED REDUCER (70057696)
6.33 OIL RESERVOIR ASM-60 GAL (51714218)
6.34 KIT-CONTROL (73733212)
6.35 CTRL BOX-RADIO (51715077)
7 GENERAL REFERENCE
7.1 INSPECTION CHECKLIST
7.2 DEFICIENCY / RECOMMENDATION / CORRECTIVE ACTION REPORT
7.3 WIRE ROPE INSPECTION

7.4 HOOK INSPECTION

7.5 HOLDING VALVE INSPECTION

7.6 TWO BLOCK PREVENTION DEVICE INSPECTION

7.7 TORQUE DATA CHART – DOMESTIC
7.8 TORQUE DATA CHART – METRIC

7.9 TURNTABLE BEARING FASTENER TIGHTENING SEQUENCE
7.10 TURNTABLE BEARING INSPECTION FOR REPLACEMENT
8 CRANE SAFETY
9 VOLUME 1
10 WARRANTY POLICY
11 Gen Reference section – updated.pdf