komatsu ae50 am50 series electric lift truck shop manual bba12e1 01 1 1

komatsu ae50 am50 series electric lift truck shop manual bba12e1 01 2

komatsu ae50 am50 series electric lift truck shop manual bba12e1 01 3

komatsu ae50 am50 series electric lift truck shop manual bba12e1 01 4

komatsu ae50 am50 series electric lift truck shop manual bba12e1 01 5 1

Komatsu AE50, AM50 Series Electric Lift Truck Shop Manual BBA12E1-01

$40.00

Type Of Manual: Shop Manual
Manual ID: BBA12E1-01
Format: PDF
Size: 24.2MB
Number of Pages: 361

Category: Komatsu Shop Manual PDF

Model List:
- AE50 Series Electric Lift Truck
- AM50 Series Electric Lift Truck

1. Cover
2. DESCRIPTION OF THE SYMBOLS
3. SECTION INDEX
4. GENERAL AND SPECIFICATIONS
4.1. OUTSIDE VIEW
4.2. SPECIFICATIONS
4.3. PERIODIC REPLACEMENT OF CONSUMABLE PARTS
4.4. SAFETY ITEMS FOR MAINTENANCE
4.5. STANDARD TIGHTENING TORQUE FOR BOLTS
4.6. STANDARD TIGHTENING TORQUE FOR PIPE JOINTS
4.7. HOW TO USE LOCTITE
5. TESTING AND ADJUSTING
5.1. SERVICE DATA
5.2. METHOD OF RELEASING THE PRESSURE IN THE HYDRAULIC PIPING
5.3. LIFT INTERRUPT FUNCTION
5.4. HOW TO START UP THE HOUR METER
5.5. METER PANEL
5.6. OPERATION OF METER PANEL
5.7. BATTERY
5.8. FUSE
5.9. TRANSFER CASE
5.10. VEHICLE MOUNTED TYPE CHARGER
5.11. INSTALLATION TYPE CHARGER
5.12. ADJUSTMENT OF WET TYPE BRAKE AND PARKING BRAKE
5.13. WET TYPE BRAKE
5.14. HYDRAULIC OIL TANK
5.15. MAST
5.16. FINGER BAR
5.17. NATURALLY DESCENDING AMOUNT OF HYDRAULIC OIL CYLINDER,MEASUREMENT OF NATURALLY FORWARD TILTING AMOUNT
5.18. AIR BLEEDING
5.19. LIST OF LUBRICANT AND GREASE
6. REMOVAL AND INSTALLATION
6.1. UNIT LOCATION DIAGRAM
6.2. UNIT MASS
6.3. DRAWING OF DISASSEMBLY/ASSEMBLY
6.4. HYDRAULIC PUMP AND PUMP MOTOR
6.5. VEHICLE MOUNTED CHARGER
7. DISASSEMBLY AND ASSEMBLY
7.1. DRIVE AXLE
7.2. TRANSFER (BRAKE)
7.3. TRANSFER (HUB BEARING)
7.4. TRANSFER (TRANSFER)
7.5. BRAKE WHEEL CYLINDER
7.6. BRAKE MASTER CYLINDER
7.7. STEERING GEAR BOX
7.8. ORBITROL
7.9. POWER STEERING CYLINDER
8. MAINTENANCE STANDARD
8.1. DRIVE AXLE
8.2. BRAKE MASTER CYLINDER
8.3. MAST, FINGER BAR, FORK
8.4. DRIVE MOTOR
8.5. PUMP MOTOR
9. STRUCTURE AND FUNCTION
9.1. BRAKE
9.2. HYDRAULIC CIRCUIT DIAGRAM
9.3. CONTROL VALVE
10. TROUBLESHOOTING
10.1. DIAGNOSIS TOOL
10.2. CONFIGURATION PARTS, SENSOR, UNIT LOCATION DRAWING
10.3. LOCATION DRAWING
10.4. HARNESS LIST
10.5. LOCATION OF CPU BOARD CONNECTOR
10.6. OVERVIEW OF ABNORMAL CODE
10.7. PREPARATION FOR VOLTAGE CHECK AND CURRENT CHECK
10.8. INPUT / OUTPUT SIGNAL OF CONTROLLER
10.9. ABNORMAL CODE LIST
10.10. DIAGNOSTIC PROCEDURE BY ABNORMAL CODE
10.11. DIAGNOSTIC PROCEDURE BY METER DISPLAY TROUBLE CODE
10.12. TROUBLE WITHOUT ABNORMAL DISPLAY
10.13. PROPORTIONAL SOLENOID VALVE CONTROLLER
10.14. METER PANEL
11. YEARLY INSPECTION CRITERIA
11.1. MOTOR
11.2. CONTROL EQUIPMENT
11.3. CHARGE CONTROL UNIT
11.4. BATTERY
11.5. POWER TRANSFER EQUIPMENT
11.6. TRAVELING EQUIPMENT
11.7. STEERING EQUIPMENT
11.8. BRAKING EQUIPMENT
11.9. CARGO HANDLING EQUIPMENT
11.10. HYDRAULIC EQUIPMENT
11.11. BODY, SAFETY EQUIPMENT, ETC
11.12. TOTAL TEST
12. CONVERSION TABLE
12.1. MILLIMETERS TO INCHES
12.2. INCHES TO MILLIMETERS
12.3. CUBIC METERS TO CUBIC YARDS
12.4. CUBIC YARDS TO CUBIC METERS
12.5. LITER TO U.S GALLON
12.6. GALLON TO LITER
12.7. LITER TO U.K GALLON
12.8. GALLON TO LITER
12.9. KILOGRAM TI POUND
12.10. POUND TO KILOGRAM
12.11. Kg/cm2 to Ib /in2
12.12. kgm to ft. Ib
12.13. TEMPERATURE
13. APPENDIX
13.1. A9799710 (INPUT GEAR/BEARING PRESSFITTING JIG)
13.2. A9799720 (MULTIPLE DISC ALIGNMENT JIG)
13.3. A9799730 (MULTIPLE HOLDER CLEARANCE ALIGNING JIG)
13.4. A9799740 (3 WHEEL REAR AXLE PRESSFITTING JIG)
13.5. A9799760 (3 WHEEL REAR AXLE SENSOR ALIGNMENT JIG)
13.6. SERVICE TOOL CONFIGURATION
13.7. ELECTRIC CIRCUIT DIAGRAM

Rate this product