komatsu d155axi 8 bull dozer operation and maintenance manual ten01136 00 1

komatsu d155axi 8 bull dozer operation and maintenance manual ten01136 00 2

komatsu d155axi 8 bull dozer operation and maintenance manual ten01136 00 3

komatsu d155axi 8 bull dozer operation and maintenance manual ten01136 00 4

komatsu d155axi 8 bull dozer operation and maintenance manual ten01136 00 5

Komatsu D155AXi-8 Bull Dozer Operation and Maintenance Manual TEN01136-00

$20.00

Type Of Manual: Operation and Maintenance Manual
Manual ID: TEN01136-00
Format: PDF
Size: 14.7MB
Number of Pages: 253

Category: Komatsu Operation and Maintenance Manual PDF

Model List:
- D155AXi-8 Bull Dozer

1. Cover
2. Foreword
2.1. Table of Contents
2.2. Read This Manual
2.3. Safety Information
2.4. Introduction
2.4.1. intelligent Machine Control
2.4.2. Machine Features
2.5. Abbreviation List
3. Safety
3.1. General Precautions Common to Operation and Maintenance
3.1.1. Precautions When You Get on or Off Machine
3.1.1.1. Precautions When You Stand Up from Operators Seat
3.1.1.2. Precautions When You Move Away from Operator Seat
3.1.2. Precautions for Blade Automatic Control
3.2. Precautions for Operation
3.2.1. Start Engine
3.2.1.1. In Cold Weather
3.3. Precautions for Maintenance
3.3.1. Precautions for Check and Maintenance
3.3.1.1. Precautions When You Discard Waste Materials
3.3.1.2. Precautions for GNSS Antenna
3.3.1.3. Handle Component Which Contains Mercury
3.4. Precautions for DEF
3.4.1. General Character and Precautions for Handling
3.4.2. Precautions When You Add
4. Operation
4.1. General View
4.1.1. Names of Machine Equipment
4.1.2. Machine Outside Equipment Name
4.1.3. Control Levers and Pedals
4.1.3.1. Control Box Name
4.2. Explanation of Components
4.2.1. intelligent Machine Control System
4.2.1.1. Control Box
4.2.1.2. Network Modem
4.2.1.3. Auto/Manual Switch
4.2.1.4. Cut/Fill Offsets Switch
4.2.1.5. Back Grade Mode Switch
4.2.1.6. GNSS Antenna
4.2.1.7. GNSS Receiver
4.2.1.8. AutoPitch
4.2.2. Other Equipment
4.2.2.1. Remove and Install Control Box
4.3. Machine Operations and Controls
4.3.1. Checks and Adjustment Before You Start Engine
4.3.2. Operations and Checks After You Start Engine
4.3.2.1. Reset Cylinder Stroke End
4.3.2.2. Set Standard Angle of Blade Edge
4.3.3. How to Stop Engine
4.3.4. How to Use Automatic Blade Control
4.3.4.1. Prepare for Blade Automatic Control
4.3.4.2. Handle Automatic Blade Control
4.3.4.3. Mode Settings
4.3.4.4. Function Related with Machine Monitor Blade Automatic Control
4.3.4.5. Precautions When You Use Blade Automatic Control
4.3.4.6. Recommended Applications and Modes
4.4. Transportation
4.4.1. Handle Cylinders When Blade is Not Installed or Removing and Installing Blade
4.4.2. Remove Radio Device Antenna Cable
4.4.3. How to Remove Bracket for GNSS Antenna
4.5. Precautions for LongTerm Storage
4.5.1. Turn Battery Disconnect Switch to OFF Position Before LongTerm Storage
4.6. Troubles and Procedures
4.6.1. Other Trouble
4.6.1.1. Phenomena and Procedures for Control Box
5. Handle Control Box
5.1. Table of Contents
5.2. Overview
5.2.1. Function of Switches
5.2.1.1. Power ON/OFF and Menu Switch
5.2.1.2. Zoom in Switch
5.2.1.3. Zoom Out Switch
5.2.1.4. Toggle Main View Switch
5.2.2. Brightness and Volume Control
5.2.3. LED Indicator
5.2.4. Keyboard Functions
5.2.4.1. How to Input with Alphanumeric Keyboard
5.2.4.2. How to Input with Numeric Keyboard
5.2.5. How to Show Main Menu
5.3. File Menu
5.3.1. Project Files
5.3.1.1. How to Import and Set Project Files
5.3.1.2. How to Make Project File
5.3.1.3. How to Export Project File
5.3.2. Control Point Files
5.3.2.1. How to Import Control Point Files
5.3.3. Layers
5.3.3.1. How to Import Layers
5.3.4. Point Data
5.3.4.1. How to Register Point Data
5.3.5. Surface File
5.3.5.1. How to Import Surface Files
5.3.5.2. How to Make Flat Surface Files
5.3.5.3. How to Make Sloping Surface Files
5.3.5.4. Make Crown Road Surface File
5.3.5.5. How to Make Triangulated Surfaces from Topo Survey File
5.3.5.6. How to Make Surface Files After You Reflect Raise or Lower Quantity of an Existing Surface
5.3.5.7. How to Make Alignment File of Subgrade of Active Alignment
5.3.6. Active File
5.3.6.1. How to Select Active Surface File
5.3.6.2. Select Alignment File
5.3.6.3. How to Select Active ASBUILT View
5.3.7. Exit 3DMC
5.3.7.1. How to Exit 3DMC
5.4. Control Menu
5.4.1. Machine Setting
5.4.1.1. How to Configure Machine
5.4.2. How to Set ASBUILT Control Options
5.4.2.1. How to Add and Set ASBUILT Surface Display
5.4.2.2. How to Delete ASBUILT Surface Display
5.4.3. Blade Control
5.4.3.1. How to Set Automatic BestFit Blade Control
5.4.3.2. How to Set Single Point Blade Control
5.4.4. Steer Indication Options
5.4.4.1. How to Set Steer Indication Options
5.4.5. Adjust Wear Volume
5.4.6. Dozing Control
5.4.7. Adjust Blade Elevation
5.4.8. Calibrate Blade Position
5.5. Tools Menu
5.5.1. Radio Device Settings
5.5.2. Position Settings
5.5.2.1. How to Examine Blade Elevation
5.5.3. Navigate Points
5.5.3.1. How to Navigate to Points
5.5.4. Topo Shot for Topographic Survey
5.5.4.1. Do Topographic Surveys
5.5.5. Set Sitelink3D
5.5.5.1. Setting Contents by Sitelink3D Menu
5.5.6. Komatsu Options
5.5.6.1. How to Show Komatsu Options Screen
5.5.6.2. Komatsu Options Menu
5.5.7. Supervisor Mode
5.5.7.1. How to Use Supervisor Mode
5.5.7.2. How to Lock Menus, Buttons and Screen Items
5.5.7.3. How to Change Password
5.5.7.4. How to Finish Lock Mode
5.6. View Menu
5.6.1. Main Window Display
5.6.1.1. How to Show Main Window Display
5.6.2. Left Window Display
5.6.2.1. How to Show Left Window Display
5.6.3. Right Window Display
5.6.3.1. How to Show Right Window Display
5.6.4. Lower Window Display
5.6.4.1. How to Show Lower Window Display
5.6.5. Display Options
5.6.5.1. How to Show Display Options
5.6.5.2. How to Set Working Surface Display
5.6.5.3. How to Set Alignment Display
5.6.5.4. How to Set ASBUILT Surface Display
5.6.5.5. How to Set Point Display
5.6.5.6. How to Set Shortcuts Display
5.6.5.7. How to Set Background Color Display
5.6.5.8. How to Set Shown Units
5.6.5.9. How to Select Language
5.6.6.1. How to Show 3DMC Information
5.7. Main Window Display
5.7.1. Elevation Control Key
5.7.2. Slope Control Key
5.7.3. Shortcut on the Main Window
5.7.3.1. Toggle ASBUILT Mode
5.7.3.2. Start/Stop ASBUILT Updates
5.7.3.3. Dozing Mode Selection
5.7.3.4. Blade Load Selection
5.7.3.5. Get Topo Shot
5.7.3.6. Task Detail
5.7.3.7. Sitelink3D Messaging
5.7.3.8. Sitelink3D Work
5.7.3.9. Material Selection
5.7.4. Pan of Main Map View
5.8. Operation on Main Menu
5.8.1. How to Show GNSS Information
5.8.2. How to Adjust Cut/Fill Offsets
5.8.3. How to Change Grade Indicator Display
5.8.3.1. How to Change Slope Display
5.8.3.2. How to Change on Grade
5.8.3.3. How to Change Range
5.8.3.4. How to Change Highlight Color
5.8.4. How to Change Display of Light Bar
5.8.5. Operation by Popup Menu
5.8.5.1. Display Extended Status Text in Plan/Profile/Section
5.8.5.2. How to Adjust Cut/Fill Offsets (Popup Menu)
5.8.5.3. How to Navigate to Points (Popup Menu)
5.8.5.4. How to Use Polyline
5.8.5.5. Move the Steer Point (Pop Up Menu)
5.8.5.6. How to Set Isolate Surface Region
6. Specifications
6.1. Specifications
6.1.1. Specifications D155AXI8
7. INDEX

Rate this product