komatsu d375a 5 bull dozer operation and maintenance manual seam048900 1

komatsu d375a 5 bull dozer operation and maintenance manual seam048900 2

komatsu d375a 5 bull dozer operation and maintenance manual seam048900 3 1

komatsu d375a 5 bull dozer operation and maintenance manual seam048900 4 1

komatsu d375a 5 bull dozer operation and maintenance manual seam048900 5

Komatsu D375A-5 Bull Dozer Operation and Maintenance Manual SEAM048900

$20.00

Type Of Manual: Operation and Maintenance Manual
Manual ID: SEAM048900
Format: PDF
Size: 1.7MB
Number of Pages: 59

Category: Komatsu Operation and Maintenance Manual PDF

Model List:
- D375A-5 Bull Dozer

1. MAIN MENU
2. D375A5 BASE MANUAL
3. COVER
4. FOREWORD
4.1. FOREWORD
4.2. SAFETY INFORMATION
4.3. INTRODUCTION
4.4. PRODUCT INFORMATION
4.4.1. LOCATION OF NAMEPLATE FOR TRANSMITTER (TX. UNIT)
4.4.2. LOCATION OF NAMEPLATE FOR RECEIVER (RX. UNIT)
4.4.3. LOCATION OF NAMEPLATE FOR CONTROLLER
4.4.4. YOUR MACHINE SERIAL NUMBERS AND DISTRIBUTOR
4.5. CONTENTS
5. SAFETY
5.1. GENERAL PRECAUTIONS
5.1.1. SAFETY RULES
5.1.2. IF ABNORMALITIES ARE FOUND
5.1.3. FIRE EXTINGUISHER AND FIRST AID KIT
5.1.4. SAFETY FEATURES
5.1.5. KEEP MACHINE CLEAN
5.1.6. INSIDE OPERATORS COMPARTMENT
5.1.7. ALWAYS APPLY LOCK WHEN LEAVING OPERATORS SEAT
5.1.8. HANDRAILS AND STEPS
5.1.9. MOUNTING AND DISMOUNTING
5.1.10. NO PEOPLE ON ATTACHMENTS
5.1.11. PREVENTION OF BURNS
5.1.12. FIRE PREVENTION
5.1.13. ACTION IF FIRE OCCURS
5.1.14. WINDOW WASHER LIQUID
5.1.15. PRECAUTIONS WHEN USING ROPS (Roll Over Protective Structure)
5.1.16. PRECAUTIONS FOR ATTACHMENTS
5.1.17. CAB WINDOW GLASSES
5.1.18. UNAUTHORIZED MODIFICATION
5.1.19. SAFETY AT WORKSITE
5.1.20. WORKING ON LOOSE GROUND
5.1.21. DO NOT GO CLOSE TO HIGHVOLTAGE CABLES
5.1.22. ENSURE GOOD VISIBILITY
5.1.23. VENTILATION FOR ENCLOSED AREAS
5.1.24. CHECKING SIGNALMANS SIGNALS AND SIGNS
5.1.25. BE CAREFUL ABOUT ASBESTOS DUST
5.2. PRECAUTIONS FOR OPERATION
5.2.1. BEFORE STARTING ENGINE
5.2.2. CHECKS BEFORE STARTING ENGINE
5.2.3. ENSURING SAFETY AT THE JOBSITE
5.2.4. INSTALLATION, INSPECTION OF RADIO CONTROL BOX
5.2.5. PRECAUTIONS WHEN STARTING ENGINE
5.2.6. PRECAUTIONS WHEN USING RADIO CONTROL FOR TRAVEL
6. OPERATION
6.1. GENERAL VIEW
6.1.1. GENERAL VIEW OF MACHINE
6.2. EXPLANATION OF COMPONENTS
6.2.1. TRANSMITTER (TX. UNIT)
6.2.1.1. CONTROL LEVERS
6.2.1.2. OPERATION METHOD FOR BLADE, DUAL TILT, AND PITCH USING RADIO CONTROL
6.2.1.3. OPERATION METHOD FOR PINPULLER USING RADIO CONTROL
6.2.1.4. OPERATION METHOD FOR SSC MODE SELECTION USING RADIO CONTROL
6.2.1.5. SWITCHES
6.2.1.6. OTHERS
6.2.2. RECEIVER UNIT (RX. UNIT)
6.2.3. CONTROLLERS
6.2.4. CHARGER
6.2.5. ROTATING LAMPS
6.2.5.1. STANDARD INSTALLATION
6.2.5.2. OPTION
6.3. HANDLING RADIO CONTROL
6.3.1. FLOW CHART FOR STARTING, OPERATING USING RADIO CONTROl
6.3.2. FLOW CHART FOR STOPPING OPERATION USING RADIO CONTROL
6.3.3. DETAILS OF PROCEDURE FOR RADIO CONTROL OPERATION
6.3.3.1. CHECKS BEFORE STARTING
6.3.3.2. Tilt angle
6.4. PRECAUTIONS WHEN OPERATING RADIO CONTROL
6.5. Operation using radio control
6.5.1. Moving off
6.5.2. Steering (changing direction of travel)
6.5.3. Work equipment (blade RAISE/LOWER/FLOAT, tilt left/right, ripper UP/DOWN, ripper tilt in/back)
6.5.4. Acceleration/deceleration
6.5.5. Stopping (braking)
6.6. PRECAUTIONS WHEN HANDLING RADIO CONTROL
6.6.1. TRANSMITTER
6.6.2. RECEIVER UNIT, CONTROLLER
6.6.3. CHARGER FOR AC, DC
6.6.4. PRECAUTIONS WHEN OPERATING FROM OPERATORS SEAT
6.7. CHECKS AROUND MACHINE
6.7.1. HYDRAULIC UNIT
6.7.2. RECEIVER UNIT, CONTROLLER
6.7.3. ANTENNA
6.7.4. ROTATING LAMPS
6.8. IF ANY FAILURE IS SUSPECTED
6.8.1. Radio control operation
6.8.2. Onboard operation (only problems related to radio control)
6.8.3. REPORTING FAILURE

Rate this product