komatsu fb15sh 6 fb18sh 6 electric lift truck shop manual fb15sh 18sh6 be1 1

komatsu fb15sh 6 fb18sh 6 electric lift truck shop manual fb15sh 18sh6 be1 2

komatsu fb15sh 6 fb18sh 6 electric lift truck shop manual fb15sh 18sh6 be1 3

komatsu fb15sh 6 fb18sh 6 electric lift truck shop manual fb15sh 18sh6 be1 4

komatsu fb15sh 6 fb18sh 6 electric lift truck shop manual fb15sh 18sh6 be1 5

Komatsu FB15SH-6, FB18SH-6 Electric Lift Truck Shop Manual FB15SH_18SH.6-BE1

$40.00

Type Of Manual: Shop Manual
Manual ID: FB15SH_18SH.6-BE1
Format: PDF
Size: 7.7MB
Number of Pages: 256

Category: Komatsu Shop Manual PDF

Model List:
- FB15SH-6 Electric Lift Truck
- FB18SH-6 Electric Lift Truck

1. AHFORE
1.1. FOREWORD
2. AHGEN
2.1. GENERAL AND SPECIFICATIONS
2.1.1. Overall dimensions and specifications
2.1.2. Weight of main components
2.1.3. Standard tightening torque for bolts
2.1.4. Standard tightening torque for pipe joints
2.1.5. Periodical replacement of safetyassuring parts
2.1.6. General locations
2.1.7. Instruments and controls
3. AHCONV
3.1. CONVERSION TABLE
3.1.1. Millimeters to Inches
3.1.2. Inches to millimeters
3.1.3. Cubic meters to Cubic yards
3.1.4. Cubic yards to Cubic meters
3.1.5. Liters to U.S. Gallon
3.1.6. Gallon to Liter
3.1.7. Liter to U.K. Gallon
3.1.8. Gallon to Liter
3.1.9. Kilogram to Pound
3.1.10. Pound to Kilogram
3.1.11. kg/cm to lb/in
3.1.12. Kgm to Ft. lb
3.1.13. Temperature
4. AHDIS
4.1. DISASSEMBLY AND ASSEMBLY OF COMPONENTS
4.1.1. POWER TRAIN
4.1.1.1. Transfer
4.1.1.2. Wheel brake
4.1.1.3. Differential
4.1.1.4. Drive axle
4.1.2. BRAKE SYSTEM
4.1.2.1. Master cylinder
4.1.2.2. Wheel brake
4.1.2.3. Air vent
4.1.3. STEERING SYSTEM
4.1.3.1. Power steering valve
4.1.3.2. Steering axle
4.1.3.3. Power steering cylinder
4.1.4. HYDRAULIC SYSTEM
4.1.4.1. Hydraulic circuit diagram
4.1.4.2. Hydraulic pump
4.1.4.3. Control valve
4.1.4.4. Control valve lever
4.1.4.5. Lift cylinder (For Komatsumade mast)
4.1.4.6. Tilt cylinder
4.1.5. MAST
4.1.5.1. Mast (Komatsumade)
4.1.5.2. Mast (Cascademade)
5. AHELEC
5.1. ELECTRICAL SYSTEM
5.2. ELECTRICAL COMPONENTS
5.3. Digital multimeter
5.4. BATTERY AND CASE
5.5. Battery compartment
5.6. Notes on selecting a battery
5.7. Recommended batteries
5.8. MOTORS
6. AHREMOV
6.1. REMOVAL AND INSTALLATION OF UNITS
6.1.1. Locations of units
6.1.2. How to install units
6.1.3. Removal and installation flowcharts
6.1.4. Removal and installation of units
6.1.4.1. Mast (Komatsumade)
6.1.4.2. Lift cylinder (Komatsumade)
6.1.4.3. Mast (Cascademade)
6.1.4.4. Lift cylinder (Cascademade)
6.1.4.5. Power train (Drive axle, Transfer and Traction motor)
6.1.4.6. Pump motor
6.1.4.7. Power steering motor
6.1.4.8. Steering axle
6.1.4.9. Power steering cylinder
7. AHTEST
7.1. TESTING AND ADJUSTING
7.1.1. Motor
7.1.2. Battery
7.1.3. Controller
7.1.4. Travel system
7.1.5. Steering system
7.1.6. Brake system
7.1.7. Work equipment system
7.1.8. Adjustment of parking brake lever
7.1.9. Adjustment of brake pedal
7.1.10. Adjustment of accelerator pedal
7.1.11. Adjustment of operators seat switch
8. AISM013
8.1. GENERAL MAINTENANCE INSTRUCTIONS
8.2. A COMPARISON OF GE EV100LXT CONTROLLER WITH THE EXISTING CONTROLLER
8.3. HANDSET SETTINGS ON MACHINES SHIPPED FROM FACTORY
8.4. LIST OF FUNCTION, EV100LXT TRACTION CONTROLLER FOR ABX
8.5. MAIN SPECIFICATIONS OF MOTOR AND SERVICE DATA
8.6. BASICS OF CIRCUIT OPERATION
8.7. OUTLINE OF CONTROLLER
8.7.1. Description of Control Functions
8.7.2. Dimensions of Traction SCR Panel
8.7.3. External View of Traction SCR Panel
8.7.4. Wiring of Traction SCR Panel
8.7.5. Contactor Panel
8.7.6. Accelerator
8.8. HYDRAULIC PUMP OPERATION (Contactor Type)
8.9. DEADMAN HORN ALARM CIRCUIT
8.10. GLOSSARY
8.11. ELEMENTARY DIAGRAM SYMBOLS
8.12. PROCDURES FOR REPLACING CONTROLLER COMPONENT PARTS
8.12.1. Control Card
8.12.2. Stud semiconductors
8.12.3. Capacitor
8.12.4. FIL, 23FIL, 24FIL, and 25FIL
8.12.5. Reactor/Choke
8.13. TROUBLESHOOTING
8.13.1. Digital Multifunction Displayer
8.13.2. Troubleshooting Instructions
8.13.3. Status Codes Requiring Troubleshooting by Use of Meter Panel
8.13.4. Procedure for Setting Travel Characteristics with HANDSET
8.14. SEQUENCE OF OPERATION
8.15. List of Status Codes
8.16. Troubleshooting for the Hydraulic Control with Contactor Type
8.16.1. The voltage reading at the terminals of PATD, PBTD and PAD, PBD wire
8.16.2. in normal conditions
8.16.3. Troubleshooting of hydraulic pump motor
8.16.3.1. Contactor closes and the pump motor does not rotate
8.16.3.2. The contactor does not close
8.16.3.3. No time delay after the valve switch open or the contactor tips chatters
8.17. Troubleshooting for the Horn Function
8.17.1. The voltage reading at the terminalsTMM2 normal conditions
8.17.2. Troubleshooting for the horn alarm function
8.17.2.1. The horn does not blow when the button is activated
8.17.2.2. The horn does blow with the condition listed below
8.17.2.3. The horn blows continuously
8.18. Troubleshooting of Power Steering Motor
8.18.1. Troubleshooting
8.18.2. Disassembly
8.18.3. Reassembly
8.19. Troubleshooting of the Brush for Traction and Pump Motors
8.20. Troubleshooting without use of the Meter Panel for Traction SCR Controller
8.20.1. The voltage reading at the terminalsin normal condition
8.20.2. Troubleshooting Instructions
8.21. All Testing should be Done with Truck Jacked Up
8.21.1. Failures that cause reduced or no motor torque with SCR control
8.21.2. Failures that cause full or no motor torque with SCR control
8.21.3. Misoperation of other features
8.22. Others Electrical component Parts
8.22.1. Capacitor 1C
8.22.2. Contactors F, R, 1 A and P
8.22.3. Potentiometer in accelerator
8.22.4. Coil driver module
8.22.5. SCRS (1 REC, 2REC, 5REC)
8.22.6. Rectifiers (3REC,2REC, diode blocks)
8.22.7. Thermal protector(TP)
8.22.8. Filter block (23FIL, etc)
8.22.9. choke and reactor T3T4
8.23. TROUBLESHOOTING (SYMPTOM CHART)
8.23.1. Field Weakening(F/W) Control System
8.24. CIRCUIT DIAGRAM

Rate this product